Induztr
Résumé technique Visionneuse de documents Modèles associés

Controlling Contamination in LC/MS Systems

Technical Reference Summary

Covered Models & Document Scope

El documento 715001307 Versión 09 cubre las mejores prácticas para el control de la contaminación en UPLC/MS, HPLC/MS y sistemas MaxPeak Premier (tanto clínicos como no clínicos). Se aplica a los sistemas LC/MS de Waters, incluidos ACQUITY UPLC, ACQUITY Premier, nanoACQUITY, M-Class, Alliance HPLC y sistemas MaxPeak Premier, y hace referencia a componentes con etiqueta HPS.

Section-by-Section Technical Breakdown

pp. 3-10
Prevención de la contaminación

La prevención es el factor más importante en el control de la contaminación. La sección cubre la selección y manipulación de disolventes, la limpieza del material de vidrio, la preparación de muestras, los racores y la tubulación, los guantes, las columnas y el aire del laboratorio. Proporciona procedimientos detallados para evitar introducir contaminantes en el sistema LC/MS.

  • Use UPLC-grade or application-suitable solvents; use freshest solvents and prevent microbial growth.
  • Use ultra-pure water with >18 MOhm.cm resistivity, no particles >0.2 microns, and low UV absorbance.
  • Prepare, filter, and degas aqueous mobile phase daily; flush with water then at least 10% organic during shutdown.
  • Store mobile phases in clean amber or brown-stained borosilicate glass reservoirs (type 1, class A, or type 3.3).
  • Do not top off solvents; discard old solvent, rinse bottles and inlet filters, refill with fresh solvent, and prime.
  • Clean glassware with organic solvent then water; aggressive cleaning uses sonication with 10% formic or nitric acid, water, methanol or acetonitrile, then water, repeated three times.
  • Use Waters-brand vials and wellplates; avoid paper-lined caps, self-sealing septa containing silicone, and adhesive cap mats.
  • Use clean inert fittings and tubing; avoid PVC tubing and labels contacting solvents.
  • Wear particulate-free, powder-free, non-latex gloves (Waters sterile nitrile gloves, part numbers 700002964 size 7 and 700002965 size 9).
  • Store columns in original solvent (e.g., 100% acetonitrile) and flush buffers/additives before storage.
pp. 11-15
Solución de problemas de contaminación

Esta sección proporciona un enfoque sistemático para aislar la contaminación en el sistema LC o MS. Incluye un diagrama de flujo y procedimientos paso a paso para comprobar la fase móvil, el gestor de disolventes/bomba, el gestor de muestras/autosampler, los componentes del inyector y los componentes del front-end del MS.

  • Use the flowchart on page 11 to determine if contamination is continuous background or chromatographic peaks.
  • Flush ESI probe with clean solvent and infuse directly to isolate LC vs MS contamination.
  • Check mobile phase by infusing a 50:50 A/B mixture; if contaminated, problem is in bottles or mobile phase.
  • Make a zero-volume injection to distinguish solvent manager/pump from sample manager/autosampler contamination.
  • Check sample manager/autosampler by pumping wash solution, injecting large volumes, and checking diluent, sample, infusion device, and container.
  • Change injection volume by a factor of 2 or more; if contamination scales with volume, sample is contaminated.
  • Change injection mode; PLNO mode can cause more carryover than partial loop or full loop.
  • Check needle wash solutions, injector tubing and fittings (especially injector outlet to column inlet), and replace needle if hydrophobic compounds adsorb to PEEK.
  • For MS contamination, check front-end components: ESI probe, sample cone, LockSpray baffle, ion source block, source enclosure, PEEK tubing, integral flow divert/injection valve, throttle valve, PEEK support block, LC tubing, nitrogen gas tubing and source.
  • Remove, clean or replace, and test components one at a time; if contamination persists, clean and replace all suspected parts simultaneously.
pp. 16-22
Limpieza para eliminar la contaminación

Esta sección proporciona directrices generales y mezclas de limpieza específicas para entradas LC y sistemas MS. Cubre la limpieza de columnas, gestor de disolventes/bomba, gestor de muestras/autosampler, fluidics, fuente API y sondas, con advertencias para componentes HPS y compatibilidad de materiales.

  • Remove column and detector before cleaning; use highest-purity solvents and acid or base.
  • Flush with high-organic solvent such as 80% organic/20% water and repeat until background is acceptable.
  • Bypass HPS components when cleaning MaxPeak Premier Systems and before flushing with phosphoric acid.
  • Recommended cleaning mixtures for LC inlets: (1) 80% IPA/10% water/10% formic acid for HPLC/UPLC or 1% formic acid for HPS/MaxPeak Premier; (2) 80% IPA/10% water/10% ammonium hydroxide for HPLC/UPLC or 0.1% ammonium hydroxide for HPS/MaxPeak Premier; (3) 30% phosphoric acid/70% water; (4) 100% IPA.
  • After any wash, rinse with 50% acetonitrile or mobile phase; after phosphoric acid, pump ultra-pure water until pH near 7.
  • Clean reversed-phase columns at end of run with high-percentage organic mobile phase (e.g., 80%).
  • For MS components, wipe with clean swab or lint-free wipe, sonicate 15 minutes to 1 hour in solvent, rinse with fresh solvent, and dry with clean dry nitrogen.
  • Replace contaminated API probes and LC tubing rather than cleaning.
  • Do not sonicate PEEK components and T-Wave assemblies in chlorinated solvents, hexane, acetone, or acids.
  • Fluidics: pay attention to rotor seal wear (circular grooves) and replace if necessary.
pp. 23-32
Información de referencia

Esta sección proporciona consideraciones sobre disolventes, posibles efectos de disolventes de baja calidad, recomendaciones de pureza de disolventes, proceso de purificación de agua, información para pedir guantes y una lista de los principales contaminantes y sus fuentes.

  • Low-quality solvents can cause increased back pressure, clogged tubing/columns, pump/injector damage, noisy baselines, ghost peaks, loss of sensitivity, and shifting retention times.
  • LC/MS solvent purity recommendations: assay ≥99.9%, filtered ≤0.2 microns, metal ion limits (e.g., Fe ≤20 ppb for acetonitrile/methanol/isopropanol, ≤10 ppb for water), residue after evaporation ≤25 ppb.
  • Ultra-pure water purification must include reverse osmosis, UV sterilization, ion exchange, carbon filtration, and 0.2-µm membrane filter.
  • Flush water outlet lines if without flow >24 hours; do not store purified water >24 hours without measures to prevent microbial growth.
  • Nitrile gloves: part number 700002964 (size 7, 3 pairs) and 700002965 (size 9, 3 pairs).
  • Major contaminants include PEG (peaks separated by 44 Da), metal ions (Fe-acetate clusters), and phthalates (plasticizers).

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
No utilice sistemas MaxPeak Premier fuera del intervalo de pH 1.0 a 12.5; no utilice componentes con etiqueta HPS con fases móviles de pH >10.0 ni con disolventes clorados o bromados. p.1 ↗ Operating outside specified pH range can increase wear on components not in maintenance kits and require more frequent maintenance. MaxPeak Premier Systems and HPS components
El agua ultrapura se define como estéril, sin partículas >0.2 micras, sin compuestos ionizables detectables (resistividad >18 MOhm.cm) y con baja absorbancia UV. p.4 ↗ Use of ultra-pure water reduces impurities that can collect on the column during equilibration. All LC/MS systems
Prepare, filtre y desgasifique la fase móvil acuosa a diario; durante paradas o periodos prolongados, lave el sistema completamente con agua y luego con al menos 10% de disolvente orgánico (p. ej., acetonitrilo o metanol). p.4 ↗ Prevents microbial growth that can cause peaks, high back pressure, and system shutdown. All LC/MS systems
No almacene el sistema en agua ni en fase móvil acuosa >90%. p.4 ↗ Prevents microbial contamination. All LC/MS systems
Para lavar el sistema después de usar fase móvil con aditivos, lave durante al menos 5 minutos (al menos 50 mL de agua) y luego continúe con al menos 10% de disolvente orgánico. p.5 ↗ Removes additives and prevents contamination. All LC/MS systems
Evite disolventes con pH >10 si el sistema contiene componentes de sílice fundida y vidrio (p. ej., nanoACQUITY o M-Class UPLC); lave y almacene en metanol o en al menos 10% de orgánico sin aditivos ni tampones. p.5 ↗ High pH dissolves silica; prevents damage to fused silica and glass components. nanoACQUITY, M-Class UPLC, and systems with fused silica/glass
Almacene las fases móviles en depósitos de vidrio borosilicato ámbar o teñido de marrón limpios de tipo 1, clase A, o tipo 3.3; cúbralos con papel de aluminio o con las tapas suministradas con el sistema. p.6 ↗ Prevents airborne contamination and leaching. All LC/MS systems
No utilice las botellas marrones en las que el fabricante envía los disolventes para almacenar disoluciones acuosas; no son de borosilicato. p.6 ↗ Prevents contamination from non-borosilicate glass. All LC/MS systems
Nunca lave el material de vidrio con detergentes ni en lavavajillas; limpie siempre el material de vidrio con la misma fase móvil/disolvente utilizada para la cromatografía. p.6 ↗ Detergents can introduce PEG and other contaminants. All LC/MS systems
Utilice guantes de nitrilo estériles de Waters (números de pieza 700002964 talla 7, 700002965 talla 9) al manipular piezas que contactan con la fase móvil o la muestra, y al sustituir piezas 'Critical Clean'. p.8 ↗ Prevents contamination from skin oils and hand creams. All LC/MS systems
Almacene las columnas en el disolvente con el que vinieron originalmente (p. ej., 100% acetonitrilo) y lávelas para eliminar tampones y aditivos antes de almacenarlas. p.9 ↗ Prevents column contamination and damage. All columns
Al infundir fase móvil en el MS para comprobar la contaminación, utilice la fase móvil usada en el sistema (p. ej., 50:50 A/B a 0.3 mL/min) y puentee todo el LC y el sistema de gestión de disolventes. p.12 ↗ Correctly isolates contamination source. All LC/MS systems
El modo de inyección partial loop needle overfill (PLNO) puede causar más carryover que el modo partial loop o full loop porque la muestra se aspira a través del VDD, que no se lava con lavado fuerte de aguja. p.14 ↗ Consider changing injection mode if carryover persists. Sample managers with PLNO mode
Para la limpieza de la entrada LC, las mezclas recomendadas incluyen: 80% IPA/10% agua/10% ácido fórmico (HPLC/UPLC) o 1% ácido fórmico (HPS/MaxPeak Premier); 80% IPA/10% agua/10% hidróxido de amonio (HPLC/UPLC) o 0.1% hidróxido de amonio (HPS/MaxPeak Premier); 30% ácido fosfórico/70% agua; 100% IPA. p.19 ↗ Select appropriate cleaning mixture based on contaminant and system compatibility. LC inlets of UPLC, HPLC, MaxPeak Premier, HPS components
Nunca utilice la mezcla de limpieza con hidróxido de amonio (lavado básico) en ACQUITY M-Class, nanoACQUITY ni en ningún sistema que contenga tubulación capilar de sílice que se disuelva a >pH 10. p.19 ↗ Prevents damage to silica capillary tubing. ACQUITY M-Class, nanoACQUITY, systems with silica capillary tubing
Después del lavado con ácido fosfórico, bombee agua ultrapura a través del sistema hasta que el pH esté próximo a neutro (pH=7). p.17 ↗ Prevents retention time problems and phosphate precipitation. All LC/MS systems
Sonicar los componentes del MS en disolvente durante 15 minutos a 1 hora; pueden requerirse tiempos más largos si los caudales son bajos (p. ej., M-Class). p.21 ↗ Effective removal of contamination may require several sonication steps with fresh solvent. MS components
No sonique componentes PEEK ni conjuntos T-Wave en disolventes clorados, hexano, acetona o ácidos. p.22 ↗ Prevents damage to PEEK and T-Wave assemblies. PEEK components and T-Wave assemblies
Recomendaciones de pureza de disolventes LC/MS: ensayo ≥99.9%, filtrado ≤0.2 micras, hierro ≤20 ppb (acetonitrilo/metanol/isopropanol) o ≤10 ppb (agua), residuo después de evaporación ≤25 ppb. p.28 ↗ Use these criteria when selecting solvents for high sensitivity. All LC/MS systems
La purificación de agua ultrapura debe incluir ósmosis inversa, esterilización UV, intercambio iónico, filtración de carbón y un filtro de membrana de 0.2 µm de grado farmacéutico. p.29 ↗ Ensures water meets purity requirements for LC/MS. Water purification systems

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
Continuous background noise p.11 ↗ Contamination in LC or MS system; use flowchart to isolate. Follow troubleshooting flowchart on page 11 to isolate problem to LC or MS. Troubleshooting Contamination flowchart
Chromatographic peaks p.11 ↗ Contamination in LC or MS system; use flowchart to isolate. Follow troubleshooting flowchart on page 11 to isolate problem to LC or MS. Troubleshooting Contamination flowchart
Peaks found in gradient blank without injecting p.11 ↗ Contamination in mobile phase or LC system. Check mobile phase and solvent manager/pump; see Troubleshoot the LC system. Flowchart step
Peaks found after removing column and running blank p.11 ↗ Contamination in LC system before column. Check solvent manager/pump and sample manager/autosampler. Flowchart step
Contamination levels decrease when flushing ESI probe with clean solvent and infusing directly p.12 ↗ Contaminants primarily located in LC system. Troubleshoot the LC system, page 12. Isolate the problem to the LC or MS system
Contamination spectra do not decrease in intensity when infusing directly p.12 ↗ Source of contamination probably in MS system (source, inlet tubing, fluidics unit, etc.). Troubleshoot the MS system, page 15. Isolate the problem to the LC or MS system
Contamination exists when infusing 50:50 A/B mixture p.12 ↗ Problem is in the bottles or mobile phase. See guidelines on using clean solvents and containers in Preventing contamination, page 3. Check the mobile phase
Contamination exists when pumping 50:50 A/B through clean probe into MS p.12 ↗ Contamination located in solvent manager/chromatographic pump or sample manager/autosampler (or both). Make a zero-volume injection to determine which component. Check the mobile phase
Contaminants present on zero-volume injection p.12 ↗ Solvent manager/chromatographic pump is source. Check the solvent manager/chromatographic pump. Make a zero-volume injection
No contaminants present on zero-volume injection p.12 ↗ Sample manager/autosampler is source. Check the sample manager/autosampler. Make a zero-volume injection
Contamination exists when pumping directly from solvent manager/pump into MS p.13 ↗ Solvent manager/chromatographic pump is source of contamination. Reconnect sample manager/autosampler and follow General guidelines, page 16. Check the solvent manager/chromatographic pump
No contamination when pumping directly from solvent manager/pump into MS p.13 ↗ Sample manager/autosampler is source. Check the sample manager/autosampler. Check the solvent manager/chromatographic pump
Contamination persists after checking sample diluent p.13 ↗ Contamination came with original sample. Check the sample; new sample or further sample clean-up may be required. Check the sample manager/autosampler, step 3
Contamination increases or decreases in proportion to injection volume change p.13 ↗ Sample is contaminated. New sample or further sample clean-up may be required. Change the injection volume
Sample volume change has no effect on size of carryover peak p.13 ↗ Carryover not from sample volume. Change the injection mode. Change the injection volume
Contamination persists after changing injection mode p.14 ↗ Needle wash solutions may be incorrect. Check the needle wash solutions; use correct wash solutions. Change the injection mode
Contamination persists after checking needle wash solutions p.14 ↗ Tubing and fittings on injector may have dead volume. Check tubing and fittings on injector, especially injector outlet to column inlet; replace tubing and fittings. Check the needle wash solutions
Contamination persists after replacing tubing and fittings p.14 ↗ Hydrophobic compounds adsorb to PEEK needle. Replace needle; if persists, try stainless steel needle. Check the tubing and fittings on the injector
Contamination persists after replacing needle p.14 ↗ Other injector parts contaminated. Replace other injector parts (e.g., needle wash port, injector valve pod). Replace the needle
High background noise after testing MS component p.15 ↗ Last component added is contaminated or MS components recontaminated after cleaning. Clean or replace the last component added; clean and replace all suspected parts simultaneously. Clean or replace the contaminated component