Induztr
Résumé technique Visionneuse de documents Modèles associés

Agilent 6200 Series TOF and 6500 Series Q-TOF LC/MS Quick Start Guide

Technical Reference Summary

Covered Models & Document Scope

Abarca los sistemas Agilent 6200 Series TOF LC/MS (6224, 6230) y 6500 Series Q-TOF LC/MS (6520B, 6530A/B, 6538A, 6540A/B, 6545, 6545XT, 6546, 6550, 6560 Ion Mobility) con MassHunter Workstation Software versiones B.09.00 y 10.0; módulos LC compatibles 1200, 1260, 1260 Infinity II, 1290 Infinity, 1290 Infinity II y fuentes de iones ESI, Dual ESI, AJS ESI, Dual AJS ESI, APCI, APPI, Multimode, nanospray, dual nanospray, MALDI, GC-APCI.

Section-by-Section Technical Breakdown

pp. 23
Fuentes compatibles para todos los Autotunes

Enumera qué fuentes de iones son compatibles con todos los procedimientos de ajuste automatizado en cada modelo TOF y Q-TOF. Las fuentes NanoESI, Dual nanoESI, MALDI y GC-QTOF no se pueden utilizar para ningún ajuste automatizado. La fuente Dual ESI es compatible con todos los Autotunes en todos los instrumentos.

  • 6224 TOF: ESI, Dual ESI
  • 6230 TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
  • 6520B Q-TOF: ESI, Dual ESI
  • 6530A/B Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
  • 6538 Q-TOF: ESI, Dual ESI
  • 6540A/B Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
  • 6545, 6545XT, 6546 Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
  • 6550: ESI, Dual ESI, AJS ESI, Dual AJS ESI
  • 6560: Dual ESI, Dual AJS ESI
  • 6545XT ships with dielectric capillary; resistive capillary required for Fast Polarity Switching
pp. 21-28
SWARM Autotune

Describe el algoritmo de autotune SWARM utilizado en los instrumentos 6224/6230 TOF y 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF. Combina Particle Swarm Optimization y un algoritmo simplex, intercambiándolos entre ajuste grueso y fino, con parámetros limitados por la física de iones. System Tune es el SWARM Initial Auto Tune que incluye el ajuste del detector y requiere el rango de masas Standard (3200 m/z).

  • System Tune requires Standard (3200 m/z) Mass Range
  • Transmission Tune does not include detector tune; run as frequently as needed
  • Low (1700 m/z) Mass Range disables System Tune
  • High Resolution Slicer Mode must be selected before System Tune
  • Set Detector Gain and System Tune only with mass range 3200 m/z
  • Fragile Ions checkbox reduces Fragmentor Voltage to minimize fragmentation
pp. 29-34
Classic Autotune

Cubre el flujo de trabajo de autotune clásico para instrumentos TOF y Q-TOF distintos de los modelos SWARM. Initial Tune, Standard Tune y Set Detector Gain requieren el modo de instrumento Extended Dynamic Range y el rango de masas Standard (3200 m/z). Después de cambiar el rango de masas o el modo de instrumento, se requiere recalibración.

  • Instrument Mode must be Extended Dynamic Range for Set Detector Gain, Standard Tune, Initial Tune
  • Mass Range must be Standard (3200 m/z) for Set Detector Gain and Initial Auto Tune
  • High Resolution Slicer Mode required before Initial Auto Tune
  • For 6530 with Dual AJS ESI, 6538 or 6540, do not click Both; tune TOF then Quadrupole with tuning mix change
  • Software B.05.01 SP1 or later: additional Quad Tune in 1700 m/z range after Initial Tune improves molecules < 300 m/z
pp. 24, 33
Dilución del ESI-L Tune Mix

Especifica las relaciones de dilución del tune mix por modelo de instrumento, fuente y polaridad. El autotune puede fallar en 6530A, 6540A, 6545A, 6545XT, 6546, 6550A y 6560A con AJS ESI o Dual AJS ESI a menos que se diluya el tuning mix. La polaridad de iones negativos generalmente requiere dilución para una calibración adecuada.

  • 6545, 6545XT, 6550A, 6560A with Dual AJS ESI: 1:10 dilution both polarities
  • 6530 with Dual AJS ESI: 1:10 positive, 1:40 negative
  • 6538A: undiluted tune mix
  • 6230 TOF with AJS/Dual AJS ESI: 1:10 positive, 1:40 negative
  • 6224 TOF with Dual ESI: do not dilute for positive ion
  • 6550 Q-TOF always uses 1:10 dilution
pp. 28-29, 33
Calibrar el eje de masas

Explica la calibración del eje de masas: se infunde una muestra con masas conocidas y se miden los tiempos de vuelo para calcular los coeficientes de calibración actualizados. Se requiere recalibración y verificación del ajuste después de cambiar Instrument Mode, Mass Range o Slicer Mode. Mass Calibration se activa mediante Mass Calibration/Check, Quick Tune, Standard Tune o Initial Auto Tune (Classic) o mediante Mass Calibration/Check, Transmission Tune o System Tune (SWARM).

  • Recalibrate after changing Instrument Mode, Mass Range or Slicer Mode
  • 6545 with 50-250 m/z option uses calibrant ions below 100 m/z
  • Repeat Mass Calibration/Check if calibrant abundances exceed 480,000 (6538/6540) or ~650,000 (other TOF/Q-TOF)
  • Agilent recommends regular mass-axis calibration
pp. 17-19
Paso 2. Preparar los módulos LC

Describe la preparación del LC antes de la adquisición MS: desviar el flujo del LC a residuos mientras se acondiciona/equilibra la columna, purgar la bomba del LC, acondicionar la columna, configurar la monitorización de valores reales en tiempo real con límites mín./máx. y configurar las visualizaciones de gráficos en tiempo real.

  • Switch LC Stream to Waste in Method Editor General tab before conditioning column
  • Apply Now sends only the current LC eluent value; Apply sends all method parameters
  • Purge the LC pump per the pump User Guide
  • Actuals window: set min/max values; out-of-range values shown with red background
  • Monitor baseline to confirm column equilibration
pp. 21-36
Paso 3. Preparar el instrumento TOF y Q-TOF

Cubre el ajuste del instrumento TOF o Q-TOF: cuándo se requiere el ajuste, selección de autotune SWARM vs Classic, fuentes compatibles, dilución del tune mix, calibración del eje de masas y cambio del flujo del LC de Waste a MS después del ajuste. También cubre la monitorización de la línea base del MS y el uso del System Logbook Viewer.

  • Tune first use or after maintenance, service or pump-down and restart
  • Switch LC stream to MS after conditioning column and tuning
  • Monitor TOF/Q-TOF baseline stability and absence of interfering spectra
  • System Logbook Viewer: click Log on Data Acquisition toolbar or enable task bar notification
  • Manual tune recommended only for ion source and optics 1; not after collision cell
pp. 12-14
Ventanas de Data Acquisition

Describe las siete ventanas de Data Acquisition: Instrument Status, Actuals, Chromatogram Plot, Spectrum Pane, Method Editor, Sample Run y Worklist. Instrument Status muestra el estado del dispositivo mediante texto y codificación por colores; Method Editor contiene los parámetros de adquisición y, para el 6560, la sección Acquisition Mode.

  • Instrument Status window shows each device status as text and color-coded
  • Actuals window shows current values of selected parameters with conditional formatting
  • Spectrum Pane shows spectra from different devices on different tabs
  • Sample Run window supports Override DA Method and Method Type Both Acquisition and DA or DA Only
  • Worklist window runs samples in listed order; Part of method to run options Acquisition Only, Both Acquisition and DA, DA only
pp. 15
Ventana Tune

La ventana Tune se utiliza para ajustar el espectrómetro de masas con algoritmos automatizados o manualmente, seleccionar el modo de instrumento y calibrar. Para el 6560 Ion Mobility Q-TOF contiene la sección Acquisition Mode (IM-QTOF o QTOF-Only). Existen opciones adicionales de autotune para moléculas pequeñas para 6545, 6545XT, 6550 y 6560; el 6545XT también admite autotune para moléculas grandes.

  • Manual tuning recommended only for ion source and optics 1
  • 6560: select IM-QTOF or QTOF-Only in Acquisition Mode
  • 6545, 6545XT, 6550, 6560: additional small molecule autotune options
  • 6545XT: large molecule autotune available
  • Cannot do small molecule tune after large molecule autotune; upload older system tune file or do system tune first

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
System Tune (SWARM Initial Auto Tune) solo se puede realizar con Mass Range establecido en Standard (3200 m/z). p.25 ↗ Select Standard mass range before System Tune; Low (1700 m/z) disables System Tune. 6224/6230 TOF and 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF
Se debe seleccionar High Resolution Slicer Mode antes de realizar un System Tune o Initial Auto Tune. p.22 ↗ Set Slicer Mode to High Resolution before these tunes to obtain best tuning results. Instruments with Slicer Mode option
Set Detector Gain y System Tune (TOF o Quadrupole) requieren un rango de masas de 3200 m/z. p.22 ↗ These buttons are grayed out or missing with other mass ranges or unsupported sources. SWARM and Classic autotune instruments
Classic Initial Tune, Standard Tune y Set Detector Gain requieren Instrument Mode Extended Dynamic Range. p.22 ↗ Select Extended Dynamic Range before running these autotunes; buttons gray out otherwise. Classic autotune TOF/Q-TOF instruments
Después de cambiar Instrument Mode, Mass Range o Slicer Mode, se debe recalibrar el TOF o Q-TOF. p.22 ↗ Plan a Mass Calibration/Check after any such change before acquiring data. All TOF and Q-TOF models
Repita Mass Calibration/Check si las abundancias de los iones calibradores superan 480,000 para 6538/6540 Q-TOF o aproximadamente 650,000 para otros instrumentos TOF/Q-TOF. p.33 ↗ Dilute the calibration solution and repeat the check when abundances exceed these limits. 6538/6540 Q-TOF and other TOF/Q-TOF
El 6550 Q-TOF siempre utiliza solución de calibración diluida 1:10. p.33 ↗ Do not repeat Quick Tune for dilution on the 6550; dilution is always applied. 6550 Q-TOF
Para aplicaciones de moléculas pequeñas en 6550 Q-TOF, establezca Quad AMU en 100 en polaridad positiva y 90 en polaridad negativa antes del autotune. p.31 ↗ Click Apply after each polarity change to save the Quad AMU value. 6550 Q-TOF
Para 6530 con Dual AJS ESI, 6538 o 6540 en autotune clásico, no haga clic en Both; ajuste primero TOF y luego Quadrupole con un cambio de tuning mix. p.32 ↗ Tuning mix must be changed between TOF and Quadrupole tunes on these models. 6530 with Dual AJS ESI, 6538, 6540
Fast Polarity Switching Enabled restringe el autotune a Mass Calibration/Check o FPS System Tune (SWARM) o Mass Calibration/Check o FPS Initial Auto Tune (Classic). p.23 ↗ Polarity and Quadrupole/TOF/Both selections are unavailable when FPS is enabled. 6224/6230 TOF and 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF
El 6545XT se suministra con un capilar dieléctrico; se debe pedir a Agilent un capilar resistivo para utilizar Fast Polarity Switching. p.23 ↗ Order the resistive capillary if FPS is required on a 6545XT. 6545XT Q-TOF
Las fuentes NanoESI, Dual nanoESI, MALDI y GC-QTOF no se pueden utilizar para ningún ajuste automatizado. p.23 ↗ Only Mass Calibration/Check and Quick Tune (if available) are possible with these sources. 6200 Series TOF and 6500 Series Q-TOF
La fuente Dual ESI es compatible con todos los Autotunes en todos los instrumentos. p.34 ↗ Use Dual ESI when a source must support every autotune procedure. All TOF and Q-TOF models
Transmission Tune tarda aproximadamente de seis a diez minutos y no incluye el ajuste del detector. p.28 ↗ Run Transmission Tune regularly, e.g. when a different sample class is analyzed. SWARM autotune instruments
La verificación del ajuste tarda aproximadamente 30 segundos. p.27 ↗ A quick check can be used to decide whether further tuning is needed. SWARM autotune instruments
Quick Tune tarda de 7 a 10 minutos y no se puede ejecutar si se selecciona Quadrupole o Both como parte a ajustar. p.33 ↗ Select TOF only when running Quick Tune. Classic autotune instruments
Standard Tune tarda de 10 a 15 minutos para la parte TOF y de 10 a 15 minutos para la parte Quadrupole. p.34 ↗ Allow sufficient time when running a Standard Tune on both parts. Classic autotune instruments
Si la casilla Fragile Ions está marcada, Fragmentor Voltage se reduce para minimizar la fragmentación. p.28 ↗ Expect lower calibrant ion signal but increased transmission of fragile ions such as metabolites and glycans. SWARM autotune instruments
Para 6545XT con High (10K - 30K m/z) Mass Range, se realiza un ajuste de transmisión para moléculas grandes durante un transmission tune. p.21 ↗ Select the specific mass range with the slider in the Instrument State tab. 6545XT Q-TOF
El ajuste manual se recomienda solo para la parte frontal del instrumento: fuente de iones y optics 1. p.15 ↗ Do not manually tune parameters after the collision cell; manual tuning may give less than optimal results. All TOF and Q-TOF models
MassHunter 10.0 solo admite el Agilent 6546; no se admiten otros espectrómetros de masas TOF o Q-TOF en esa versión. p.5 ↗ Use MassHunter B.09.00 for other TOF/Q-TOF models. MassHunter Workstation 10.0

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
Autotune can fail p.24 ↗ Tuning mix not diluted on 6530A, 6540A, 6545A, 6545XT, 6546, 6550A or 6560A with Agilent Jet Stream ESI or Dual AJS ESI source Dilute the tuning mix as specified (e.g. 1:10 for 6545/6545XT/6550A/6560A with Dual AJS ESI) Diluting the ESI-L Tune Mix
Calibration not proper in negative ion polarity p.24 ↗ Tuning mix not diluted Dilute the tuning mix to calibrate properly Diluting the ESI-L Tune Mix
Not getting proper calibration in positive ion polarity p.24 ↗ Tuning mix not diluted Dilute the tuning mix Diluting the ESI-L Tune Mix
Problems occur if you dilute the tune mix and tune for positive ion p.24 ↗ Tune mix diluted on 6224 TOF with Dual ESI source Do not dilute the tune mix for the Dual ESI source on the 6224 TOF Diluting the ESI-L Tune Mix
Calibration masses detected out of the 50 to 650K range p.30 ↗ Calibrant ion abundance too high; fragmentor voltage cannot be adjusted low enough System tells you to dilute the calibrant and then try the calibration or autotune again Adjust abundances for optimal calibration (6530A/B)
Check tune results are not acceptable p.27 ↗ Mass calibration/optimization not within acceptance Continue with Transmission Tune; if still unacceptable, run System Tune; if System Tune results are not acceptable, contact your local field service engineer SWARM autotune steps 15-18
Transmission tune results are not acceptable p.28 ↗ Tune not within acceptance Click System Tune (select Standard (3200 m/z) Mass Range and Apply if option not available); if System Tune results are not acceptable, contact your local field service engineer SWARM autotune step 17
Quick Tune results are not acceptable p.33 ↗ Limited parameter set tune not within acceptance Continue with Standard Tune Classic autotune step 19-20
Standard Tune produces unacceptable results p.34 ↗ Standard Tune not within acceptance Run an Initial Auto Tune; after performing an Initial Auto Tune, adjust the Collision Cell Gas Pressure; if this also fails, contact Agilent Field Support Classic autotune step 20
FPS Initial Auto Tune results not acceptable p.33 ↗ Fast Polarity Switching tune not within acceptance Contact Agilent Field Support Classic autotune step 18
Cannot do a small molecule tune after a large molecule autotune p.15 ↗ Large molecule autotune performed on 6545XT Upload an older system tune file first, or do a system tune Tune window NOTE
Error you want to troubleshoot during instrument preparation p.36 ↗ Instrument or software event/error View the System Logbook Viewer: click Log on the Data Acquisition toolbar, or right-click the system task bar, click Enable Notification, then right-click LOG and click Configure View the system logbook for events and errors

Technical Data

Parameter Value Condition
Mass Range (Standard) 3200 m/z p.22 ↗ System Tune / Initial Tune / Set Detector Gain
Mass Range (Low) 1700 m/z p.21 ↗ 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF small molecule autotune
Mass Range (High) 10K - 30K m/z p.21 ↗ 6545XT large molecule transmission tune
Mass Range (High) 10000 m/z p.27 ↗ 6546
Low mass autotune range 50 - 1700 m/z p.27 ↗ Low (1700 m/z) Mass Range, Quadrupole or Both
Calibrant abundance limit 480,000 counts p.33 ↗ 6538/6540 Q-TOF; repeat Mass Calibration/Check above this
Calibrant abundance limit approximately 650,000 counts p.33 ↗ other Q-TOF and TOF instruments
Calibrant abundance range 50 to 650K counts p.30 ↗ 6530A/B Adjust abundances for optimal calibration
Check tune duration approximately 30 seconds p.27 ↗ SWARM Check tune
Transmission Tune duration approximately six to ten minutes p.28 ↗ SWARM Transmission Tune
Mass Calibration / Check duration (TOF) a few minutes p.33 ↗ Classic autotune
Mass Calibration / Check duration (Quadrupole) 2 to 5 minutes p.33 ↗ Classic autotune
Quick Tune duration 7 to 10 minutes p.33 ↗ Classic autotune
Standard Tune duration (TOF part) 10 to 15 minutes p.34 ↗ Classic autotune
Standard Tune duration (Quadrupole part) 10 to 15 minutes p.34 ↗ Classic autotune
Quad AMU (Positive polarity) 100 p.31 ↗ 6550 Q-TOF small molecule applications
Quad AMU (Negative polarity) 90 p.31 ↗ 6550 Q-TOF small molecule applications
Tune mix dilution (positive ion TOF tune) 1:10 diluted tune mix p.24 ↗ 6530A with Dual AJS ESI or 6540
Tune mix dilution (negative ion TOF tune) 1:40 diluted tune mix p.24 ↗ 6530A with Dual AJS ESI or 6540
Tune mix dilution (positive ion TOF tune) Undiluted tune mix p.24 ↗ 6520B or 6530 with Dual ESI
Tune mix dilution (negative ion TOF tune) Undiluted tune mix p.24 ↗ 6520B or 6530 with Dual ESI
Tune mix dilution (polarity switching tunes) Undiluted tune mix p.24 ↗ 6530A with Dual AJS ESI or 6540; 6520B or 6530 with Dual ESI
Tune mix dilution (Quad tunes) Undiluted tune mix p.24 ↗ 6530A with Dual AJS ESI or 6540; 6520B or 6530 with Dual ESI
Tune mix dilution (SWARM, both polarities) 1:10 diluted tune mix p.24 ↗ 6545, 6545XT, 6550A, 6560A with Dual AJS ESI
Tune mix dilution (positive mode) 1:10 diluted tune mix p.24 ↗ 6530 with Dual AJS ESI
Tune mix dilution (negative mode) 1:40 diluted tune mix p.24 ↗ 6530 with Dual AJS ESI
Tune mix dilution undiluted tune mix p.24 ↗ 6538A
Tune mix dilution (positive ion) 1:10 dilution p.24 ↗ 6230 TOF with AJS ESI or Dual AJS ESI
Tune mix dilution (negative ion) 1:40 dilution p.24 ↗ 6230 TOF with AJS ESI or Dual AJS ESI
Tune mix dilution do not dilute p.24 ↗ 6224 TOF with Dual ESI, positive ion
Tune mix dilution 1:10 dilution p.33 ↗ 6550 Q-TOF (always)
LC driver version A.02.19 SR2 p.5 ↗ MassHunter 10.0
LC driver version A.02.19 p.5 ↗ MassHunter B.09.00
Supported operating systems Windows 7 and Windows 10 p.5 ↗ MassHunter B.09.00