Agilent 6475 Triple Quad LC/MS System User Guide
Technical Reference Summary
Covered Models & Document Scope
Cubre el sistema Agilent 6475A Triple Quad LC/MS con las fuentes de iones compatibles: Agilent Jet Stream (AJS) ESI, Electrospray Ionization (ESI), Atmospheric Pressure Chemical Ionization (APCI), Multimode Ionization (MMI) y Nanospray ESI. Válido para MassHunter 12.0 hasta que sea reemplazado.
Section-by-Section Technical Breakdown
Describe la vista frontal del 6475A LC/TQ e identifica la fuente de iones, el panel de servicio, el interruptor de alimentación, la cubierta frontal, el indicador de estado, la botella CDS y el número de serie. También enumera las fuentes de iones compatibles y su referencia de mantenimiento.
- Front panel includes ion source, service panel, power switch, front cover, status indicator, CDS bottle, and serial number.
- Supported sources: AJS, ESI, APCI, MMI, and Nanospray ESI.
Define los estados del instrumento y los colores/patrones de parpadeo correspondientes del LED de estado y del LED del interruptor de alimentación, y explica la ventana Instrument Status codificada por colores en el programa Acquisition. También detalla qué ocurre en el modo Standby con los calentadores de la fuente, los caudales de gas y los voltajes.
- Status LED and Power Switch LED states are mapped for BOOTING, ACQUISITION, FAULT, PUMPING DOWN, VENTING, STANDBY, Vented, IDLE, POWERING DOWN, BACKGROUND SCAN, and Off.
- In Standby, source and ion optics voltages are off, spectra are not sent, and AJS sheath gas temperature, drying gas flow, and drying gas temperature are reduced.
- Instrument Status window colors: Gray Offline, Yellow Unknown, Dark Yellow Not Ready, Green Idle, Teal Standby, Purple Pre-run/Injecting, Blue Running/Post Run, Orange Tuning, Light Orange Not Ready, Red Instrument Error, Blank Disconnected.
Explica el propósito y la duración de Checktune y Autotune, la mezcla de sintonización correcta para cada tipo de fuente y cómo programar sintonizaciones automáticas semanales o mensuales. Checktune verifica el ancho de pico y el eje de masas; Autotune se ejecuta después del mantenimiento preventivo o si Checktune falla.
- Checktune takes approximately 3 minutes per polarity.
- Autotune takes approximately 15 to 20 minutes per polarity.
- Tuning mixes: ESI-L for ESI and AJS ESI, MMI-L for MMI, APCI-L for APCI.
- Scheduling supports Weekly or Monthly recurrence.
Cubre el arranque y la parada, el venteo, el inicio del software Acquisition, el uso de las ventanas de Acquisition, la preparación de los módulos LC y del Triple Quad LC/MS, la configuración de métodos de adquisición, la ejecución de muestras individuales y listas de trabajo, y la revisión de resultados. Incluye el System Activity Log para la resolución de errores.
- Vent sequence turns off spray chamber high voltages, drying gas heater, nebulization flow, detector, and lens voltages; drying gas flow is set to Standby; rough pump turns off when turbo speed is below 20 percent.
- Wait until the instrument completely vents (760 Torr) before shutting down.
- Switch LC stream to Waste when not acquiring data; switch to MS after column conditioning and tuning.
- Method Optimizer can automate MRM product ion selection, collision energies, fragmentor voltages, and source parameters.
- dMRM Method Split window splits methods with many dMRM transitions into separate methods with fewer transitions.
Proporciona procedimientos de mantenimiento rutinario y periódico para el sistema de suministro de calibrador y la válvula de desvío, las fuentes de iones, el nebulizador, la aguja de corona, el inyector de iones y la bomba rough, además de la desinfección. Especifica intervalos, herramientas, piezas y precauciones para cada tarea.
- Check calibrant levels monthly, or weekly if tuning frequently; refill if the tuning mix level is within a few millimeters of the intake tube end.
- Clean the spray chamber daily or at the end of each shift; perform weekly cleaning if contamination persists or if the spray shield or capillary cap show significant discoloration.
- Flush the nebulizer daily for 3 minutes and monthly overnight using 30% to 70% methanol in water.
- Tuning mixes are not interchangeable; changing source or inlet assembly without changing the tuning mix can cause miscalibration and mass assignment errors.
- After changing to a source that uses a different tuning mix, run calibrant for 5 minutes, perform Checktune, and run Autotune if Checktune results are not acceptable.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| El rango de temperatura de operación es de 15°C a 35°C; el rango de temperatura de almacenamiento es de -40°C a 70°C. p.2 ↗ | Ensure the laboratory ambient temperature stays within 15–35°C during operation to maintain instrument performance and avoid condensation or overheating. | 6475A LC/TQ system |
| Checktune tarda aproximadamente 3 minutos por polaridad y verifica el ancho de pico y el eje de masas. p.27 ↗ | Schedule Checktune before acquisitions to confirm mass assignment and sensitivity are within expectations without a long interruption. | 6475A LC/TQ system |
| Autotune tarda aproximadamente 15 a 20 minutos por polaridad y solo es necesario después del mantenimiento preventivo o si Checktune muestra un problema. p.27 ↗ | Plan maintenance windows of at least 30–40 minutes for a full two-polarity Autotune. | 6475A LC/TQ system |
| Selección de mezcla de sintonización: ESI-L Low Concentration Tuning Mix para ESI y AJS ESI; MMI-L Low Concentration Tuning Mix para MMI; APCI-L Low Concentration Tuning Mix para APCI. p.27 ↗ | Use the correct tuning mix for the installed source; using the wrong mix can cause miscalibration and mass assignment errors. | 6475A LC/TQ with ESI, AJS, MMI, or APCI source |
| Al ventear, la bomba rough se apaga cuando la velocidad del turbo está por debajo del 20 por ciento, y el sistema debe alcanzar 760 Torr antes del apagado. p.37 ↗ | Do not power off or unplug the instrument until venting is complete at 760 Torr to avoid turbo pump damage. | 6475A LC/TQ system |
| Después del venteo y el apagado, desenchufe el cable de alimentación principal detrás del panel de servicio para evitar el sobrecalentamiento de los componentes de la bomba turbo. p.37 ↗ | Include unplugging the main power cable in the shutdown procedure for extended idle periods. | 6475A LC/TQ system |
| En el modo Standby, la interfaz de la fuente permanece encendida, el gas de secado permanece caliente y se mantienen los caudales del nebulizador, pero los voltajes de la fuente y de la óptica de iones están apagados y el espectrómetro de masas deja de enviar espectros. p.19 ↗ | Use Standby when changing the ion source or when the instrument is not in use to keep the source warm while safely removing high voltage. | 6475A LC/TQ system |
| Para la fuente AJS en Standby, se reducen la temperatura del gas de envoltura, el caudal de gas de secado y la temperatura del gas de secado; para las fuentes APCI y multimodo, se reducen los calentadores del gas del vaporizador. p.19 ↗ | Expect longer equilibration times after returning from Standby, especially for APCI/MMI vaporizer and AJS sheath gas temperatures. | 6475A LC/TQ with AJS, APCI, or MMI source |
| Verifique los niveles de calibrador mensualmente, o semanalmente si sintoniza con frecuencia; rellene cuando el nivel de la mezcla de sintonización esté a pocos milímetros del extremo del tubo de admisión. p.64 ↗ | Low calibrant can cause failed tunes; maintain sufficient volume to keep the intake tube immersed. | 6475A LC/TQ calibrant delivery system |
| Limpie la cámara de pulverización diariamente o al final de cada turno usando una mezcla 50:50 de isopropanol de grado LC/MS y agua de grado LC/MS. p.65 ↗ | Daily cleaning reduces carryover contamination between samples and analyses. | 6475A LC/TQ ion source |
| La limpieza semanal de la cámara de pulverización usa papel abrasivo de grano 4000 y sonicación durante 5 minutos en 50:50 isopropanol/agua. p.66 ↗ | Perform weekly cleaning when daily cleaning does not resolve contamination or when the spray shield or capillary cap show significant discoloration. | 6475A LC/TQ ion source |
| Enjuague el nebulizador diariamente durante 3 minutos y mensualmente durante la noche usando 30% a 70% de metanol en agua. p.68 ↗ | Regular flushing removes traces of samples and buffers from tubing, valves, and nebulizer, reducing back pressure and spray instability. | 6475A LC/TQ nebulizer |
| Después de cambiar a una fuente que usa una mezcla de sintonización diferente, ejecute el calibrador durante 5 minutos, realice Checktune y ejecute Autotune si los resultados de Checktune no son aceptables. p.70 ↗ | This sequence ensures the instrument is correctly calibrated for the new source before acquiring data. | 6475A LC/TQ when changing source type |
| Antes de retirar una fuente ESI o AJS, ponga el sistema en Standby, ajuste la temperatura del gas lo más baja posible y deje el flujo de gas encendido durante 30 minutos para enfriar la fuente. p.70 ↗ | Cooling prevents burns from hot source components and protects the source from thermal stress during removal. | 6475A LC/TQ with ESI or AJS source |
| Para la instalación del escudo de pulverización ESI, el orificio pequeño debe estar en la parte superior (posición de las 12 en punto); use un destornillador Torx T10 para aflojar los dos tornillos de la placa extrema y girar el escudo en sentido horario. p.72 ↗ | Correct spray shield orientation is required for proper nebulization and spray stability. | 6475A LC/TQ with ESI source |
| Para la instalación de la fuente Multimode, los pasadores deben estar en las posiciones de las 6 y las 9 en punto. p.73 ↗ | Incorrect dowel orientation can prevent proper seating of the spray chamber and cause leaks or poor performance. | 6475A LC/TQ with Multimode source |
| El procedimiento de ajuste del nebulizador requiere el G1960-67470 Nebulizer Adjustment Kit y se indica por un aumento de la contrapresión del LC, pulverización fuera de eje, goteo desde el nebulizador, o cuando la aguja del nebulizador de referencia no está pulverizando. p.75 ↗ | Use the adjustment kit to inspect and correct nebulizer needle position when these symptoms appear. | 6475A LC/TQ nebulizer |
| El System Activity Log en el programa Acquisition proporciona información sobre errores para ayudar en la resolución de problemas. p.51 ↗ | Check the System Activity Log first when diagnosing instrument errors or unexpected behavior. | 6475A LC/TQ system with MassHunter Acquisition |
| El Method Optimizer puede automatizar la selección de iones producto MRM, las energías de colisión, los voltajes del fragmentador y los parámetros de la fuente. p.43 ↗ | Use Method Optimizer to reduce manual method development time for MRM transitions. | 6475A LC/TQ system with MassHunter Workstation or Networked Workstation |
| La ventana dMRM Method Split facilita la división de métodos con muchas transiciones dMRM en métodos separados con menos transiciones dMRM. p.44 ↗ | Use this window to manage method complexity and improve acquisition method performance when many transitions are required. | 6475A LC/TQ system with MassHunter Workstation or Networked Workstation |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Status LED = Red; Power Switch LED = Green p.18 ↗ | Instrument state = FAULT | Check the System Activity Log for errors and troubleshoot accordingly. | Table 1 Status indicator lights on instrument |
| Status LED = Blinking Red; Power Switch LED = Yellow p.18 ↗ | Instrument state = VENTING | Wait until the instrument completely vents (reaching 760 Torr) before proceeding. | Table 1 Status indicator lights on instrument |
| Status LED = Red; Power Switch LED = Yellow p.18 ↗ | Instrument state = Vented | The instrument is vented; proceed with maintenance or restart as needed. | Table 1 Status indicator lights on instrument |
| Status LED = Blinking Yellow; Power Switch LED = Yellow p.18 ↗ | Instrument state = BOOTING (FPGA Loaded) | Wait for boot to complete. | Table 1 Status indicator lights on instrument |
| Status LED = Yellow; Power Switch LED = Green p.18 ↗ | Instrument state = BOOTING (LINUX Loaded), STANDBY, or IDLE | Wait for the instrument to reach the expected state; if IDLE, the instrument is ready. | Table 1 Status indicator lights on instrument |
| Status LED = Blinking Green; Power Switch LED = Green p.18 ↗ | Instrument state = ACQUISITION | No action; the instrument is acquiring data. | Table 1 Status indicator lights on instrument |
| Status LED = Green; Power Switch LED = Green p.18 ↗ | Instrument state = BACKGROUND SCAN | No action; the instrument is in background scan. | Table 1 Status indicator lights on instrument |
| Status LED = Off; Power Switch LED = Blinking Yellow p.18 ↗ | Instrument state = POWERING DOWN | Wait for power-down to complete. | Table 1 Status indicator lights on instrument |
| Status LED = Off; Power Switch LED = Off p.18 ↗ | Instrument state = Off | Turn on the instrument power switch to start. | Table 1 Status indicator lights on instrument |
| Red - Instrument Error p.19 ↗ | The instrument has an error and cannot process samples. | View the System Activity Log for events and errors to identify the cause. | Instrument Status Indicators in Acquisition |
| Dark Yellow - Not Ready p.19 ↗ | The instrument is connected but is not ready to run (for example, not reaching the correct temperature or pressure required by the method). | Wait for the instrument to reach the required temperature or pressure setpoints. | Instrument Status Indicators in Acquisition |
| Light Orange - Not Ready p.19 ↗ | The device is not ready. | Check device status and method requirements. | Instrument Status Indicators in Acquisition |
| Yellow - Unknown p.19 ↗ | The device is in an unknown run state. | Check the System Activity Log and device connection. | Instrument Status Indicators in Acquisition |
| Blank - Disconnected p.19 ↗ | The connection to the instrument has been closed. | Reconnect the instrument in the Acquisition software. | Instrument Status Indicators in Acquisition |
| Increased LC back pressure, off-axis spraying, dripping from the nebulizer, or reference nebulizer needle not spraying p.75 ↗ | Nebulizer needle requires inspection/adjustment. | Perform nebulizer inspection using the G1960-67470 Nebulizer Adjustment Kit. | Inspecting the nebulizer |
Technical Data
| Parameter | Value | Condition |
|---|---|---|
| Operating temperature | 15 to 35 °C p.2 ↗ | |
| Storage temperature | -40 to 70 °C p.2 ↗ |