Agilent 6400 Series Triple Quadrupole LC/MS System Quick Start Guide
Technical Reference Summary
Covered Models & Document Scope
Couvre le système Agilent 6400 Series Triple Quadrupole LC/MS. Modèles pris en charge dans Data Acquisition B.07.00 : 6420A, 6430A, 6460A, 6460C, 6490A, 6495A. Modèles LC pris en charge : 1100, 1200, 1260, 1290, HTS, HTC. Les 6490 et 6495 incluent la technologie iFunnel ; le 6495 prend en charge les résolutions Unit, Wide et Widest et ne prend pas en charge l'autotune Fast Scan.
Section-by-Section Technical Breakdown
Décrit le démarrage du programme MassHunter Data Acquisition, les huit fenêtres principales et comment afficher/masquer et ancrer/détacher les fenêtres. Explique le code couleur de la fenêtre Instrument Status et les rôles des fenêtres Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist et Tune.
- Double-click the Data Acquisition icon on the Desktop to start the program; software engines start automatically and can be restarted via Acq System Launcher > Start Engines.
- Up to seven windows can be shown at once; windows can be floated by double-clicking the title bar and docked again.
- Instrument Status window shows device status as Error, Not ready, Pre-run, Post-run, Running, Injecting, Idle, Offline, or Standby with color coding.
- Tune window is only visible in the Tune context; Checktune and Autotune reports can be printed via Create Tune Report.
Couvre le passage du flux LC vers les déchets, la purge de la pompe LC, le conditionnement/équilibrage de la colonne, la configuration de la surveillance des actuals en temps réel et la configuration des affichages de tracés en temps réel. Inclut comment définir des plages de paramètres pour que les valeurs hors limites deviennent rouges.
- When not acquiring data, switch the LC stream away from the MS ion source to waste via right-click QQQ device > LC > Waste.
- Purge the LC pump according to the pump User Guide.
- Type LC parameters and click Apply to download them to the LC; monitor baseline to confirm column equilibration.
- Actuals can be configured via right-click Actuals list > Setup; numeric parameters can have limits that turn the background red when exceeded.
Décrit l'exécution de Checktune, Autotune ou Manual Tune, y compris les durées attendues, les sources d'ions prises en charge et les actions correctives si Checktune échoue. Couvre également les limitations de Fast Scan Autotune et le passage du flux LC vers le MS.
- Checktune takes approximately 3 minutes per polarity and evaluates mass accuracy and resolution; run it regularly.
- Checktune can be run with ESI, AJS ESI, MMI and HPLC-Chip sources.
- If Checktune fails, use Manual Tune: select Peak Width (Unit, Wide, Widest) on MS1 or MS2 tab and click Adjust Gain & Offset, then save the autotune file.
- Autotune takes approximately 30 minutes per ionization mode (25 minutes for 6490/6495); 6490/6495 Autotune only with AJS ESI source.
- Fast Scan acquisition is only supported on the 6490 for MS2 Scan and Product Ion scan; not supported on 6495.
Guide la configuration d'une méthode d'acquisition, y compris les valeurs des modules LC, les types de scan et segments du Triple Quad, les signaux chromatographiques, les courbes d'instrument stockées, les paramètres DA, les propriétés de méthode, et l'exécution d'échantillons interactifs et de worklists. Inclut les modes d'exécution verrouillé/déverrouillé et le comportement de Override DA Method.
- Scan segments table is cleared when Scan Type changes; transitions can be copied and pasted when changing from MRM to Dynamic MRM or Triggered MRM.
- Fragmentor voltage cannot be set in Acquisition for 6490 or 6495; the tune file value is always used.
- A Data Analysis method contains acquisition parameters with Qual Automation and/or Quant Automation check boxes marked.
- Locked mode prevents changing method or sample parameters during a run and prevents overwriting the data file.
- Worklist can run Acquisition Only, Both Acquisition and DA, or DA Only; Override DA Method column can specify a different DA method.
Décrit l'utilisation du programme Qualitative Analysis pour examiner les résultats, sélectionner les ions précurseur/produit pour MRM, trouver et identifier les composés, et effectuer l'extraction de caractéristiques moléculaires. Décrit l'utilisation du programme Quantitative Analysis pour configurer des lots et des méthodes, examiner les résultats Batch-at-a-Glance et requantifier à l'aide de meilleurs ajustements de calibration.
- Qualitative Analysis supports acquisition method development, MRM ion selection, compound finding/identification, and molecular feature extraction.
- Quantitative Analysis supports batch and method setup for automatic quantitation, Batch-at-a-Glance review, and outlier-based requantitation.
- Familiarization Guides and online Help provide exercises for both programs.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| Dynamic MRM peut surveiller jusqu'à 4000 transitions MRM. p.1 ↗ | Method design must stay within this transition limit when using Dynamic MRM. | 6400 Series Triple Quadrupole LC/MS |
| Checktune prend environ 3 minutes par polarité. p.3 ↗ | Schedule regular Checktune runs; budget about 6 minutes for both polarities. | 6400 Series |
| Autotune prend environ 30 minutes par mode d'ionisation pour tous les modèles sauf 6490 et 6495 ; les 6490 et 6495 prennent environ 25 minutes par mode d'ionisation. p.3 ↗ | Plan instrument downtime accordingly; Autotune should only be run when necessary. | 6400 Series; 6490/6495 exception |
| Autotune à partir des valeurs par défaut d'usine prend environ 30 minutes par polarité (tous les modèles sauf 6490/6495) ou environ 25 minutes par mode d'ionisation (6490/6495). p.3 ↗ | Use Start from Factory Defaults only if normal Autotune fails; allow extra time. | 6400 Series; 6490/6495 exception |
| Checktune peut être exécuté avec les sources ESI, AJS ESI, MMI et HPLC-Chip. p.3 ↗ | Source selection must match the installed ion source before Checktune. | 6400 Series |
| Pour tous les instruments sauf 6490 et 6495, Autotune peut être exécuté avec les sources AJS ESI, MMI et HPLC-Chip ; avec 6490 et 6495, Autotune uniquement avec la source AJS ESI. p.3 ↗ | 6490/6495 users must use AJS ESI for Autotune; other sources are not supported for Autotune on these models. | 6400 Series; 6490/6495 |
| Si Checktune échoue, sélectionnez Peak Width (Unit, Wide ou Widest) dans l'onglet MS1 ou MS2 et cliquez sur Adjust Gain & Offset ; si cela réussit, enregistrez le fichier d'autotune. p.3 ↗ | This is the first corrective action before running a full Autotune. | 6400 Series |
| L'acquisition Fast Scan n'est prise en charge que sur le 6490 avec MS2 Scan et Product Ion scan ; l'autotune Fast Scan utilise la résolution Wide (1.2), Samples = 1 et un pas de 0.2. p.3 ↗ | Do not attempt Fast Scan on other models; for 6495 increase step size to 0.3 m/z for faster scan rate. | 6490; 6495 |
| La tension Fragmentor ne peut pas être définie dans Acquisition pour 6490 ou 6495 ; elle utilise toujours la valeur du fichier de tune. p.4 ↗ | Method development for 6490/6495 must manage fragmentor via the tune file, not acquisition parameters. | 6490, 6495 |
| Le tableau Scan segments est effacé lorsque le Scan Type est modifié ; les transitions peuvent être copiées et collées de MRM vers Dynamic MRM ou Triggered MRM. p.4 ↗ | Save or copy transitions before changing scan type to avoid losing method data. | 6400 Series |
| Le mode verrouillé empêche quiconque de modifier la méthode ou les paramètres d'échantillon pendant une exécution et empêche l'écrasement du fichier de données dans Data Acquisition. p.4 ↗ | Use locked mode for regulated or unattended runs to protect data integrity. | 6400 Series |
| La rétention du System Logbook peut être définie de 1 semaine à 1 an via Tools > Purge Settings. p.3 ↗ | Configure retention to meet laboratory record-keeping requirements. | 6400 Series Data Acquisition |
| Lorsqu'aucune acquisition de données n'est en cours, passez le flux LC vers les déchets via clic droit sur l'appareil QQQ > LC > Waste. p.2 ↗ | Prevents unnecessary contamination of the MS ion source during column conditioning. | 6400 Series with LC |
| Les paramètres Actuals peuvent se voir attribuer des limites numériques ; si la valeur est hors limites, l'arrière-plan est défini sur rouge. p.2 ↗ | Use Actuals limits for at-a-glance monitoring of critical MS and LC parameters such as heater and vacuum pressure. | 6400 Series Data Acquisition |
| Le 6495 prend en charge les résolutions Unit, Wide et Widest ; l'autotune Fast scan n'est pas pris en charge pour le 6495. p.2 ↗ | 6495 method development can use all three resolution modes but must not rely on Fast Scan autotune. | 6495 |
| Les 6490 et 6495 contiennent la technologie iFunnel incluant Dual Offset Ion Funnel, Agilent Jet Stream Technology et un ensemble de désolvatation plus court avec Hexabore Capillary. p.1 ↗ | These models provide more efficient ion sampling; method sensitivity expectations differ from other 6400 models. | 6490, 6495 |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Checktune fails p.17 ↗ | MS parameters outside limits for specified mass accuracy and resolution | Use Manual Tune tab: select Peak Width (Unit, Wide, or Widest) on MS1 or MS2 tab based on which resolution failed, click Adjust Gain & Offset; if successful, save autotune file. If Checktune fails again, run Autotune. | Step 3, page 17 |
| Autotune fails p.18 ↗ | Tune parameters could not be optimized automatically | Mark Start from Factory Defaults check box and click Autotune; check progress box for reasons; if still unsuccessful, manually tune or call Agilent service engineer. | Step 3, page 18 |
| No reports printed after Autotune p.18 ↗ | Autotune did not complete successfully | Check progress box in lower right side of Autotune tab for reasons why tune failed; fix problem or call Agilent service engineer with this information. | Step 3, page 18 |
| Instrument Status window shows Red p.8 ↗ | Error status | View System Logbook for logged events and errors via Log icon, Tools > System Logbook Viewer, or taskbar LOG icon. | Table 1, page 8; page 19 |
| Instrument Status window shows Yellow p.8 ↗ | Not ready status | Wait for instrument to become ready; check device status and logbook if persists. | Table 1, page 8 |
| Instrument Status window shows Dark gray p.8 ↗ | Offline status | Check device connection and configuration; reconfigure instrument if LC modules changed. | Table 1, page 8 |
Technical Data
| Parameter | Value | Condition |
|---|---|---|
| Maximum MRM transitions (Dynamic MRM) | 4000 transitions p.1 ↗ | Dynamic MRM |
| Checktune duration | approximately 3 minutes p.16 ↗ | per polarity |
| Autotune duration | approximately 30 minutes p.17 ↗ | per ionization mode; all models except 6490 and 6495 |
| Autotune duration | approximately 25 minutes p.17 ↗ | per ionization mode; 6490 and 6495 |
| Autotune from factory defaults duration | approximately 30 minutes p.17 ↗ | per polarity; all models except 6490 and 6495 |
| Autotune from factory defaults duration | approximately 25 minutes p.17 ↗ | per ionization mode; 6490 and 6495 |
| Fast Scan step size | 0.2 m/z p.18 ↗ | 6490 Fast Scan Autotune; Wide (1.2) resolution, Samples = 1 |
| Fast Scan step size | 0.3 m/z p.18 ↗ | 6495 (Fast Scan not supported; increased step size for faster scan rate) |
| System Logbook retention period | 1 week to 1 year p.19 ↗ | Tools > Purge Settings |