Operating Instructions — vacuum pump (BA 159-EN, ed. 2.1 24.07.2023, EN)
Technical Reference Summary
Covered Models & Document Scope
Couvre les pompes à vide à palettes lubrifiées V-VCB 20 et V-VCB 25 (série V), y compris la variante avec clapet de ballast à gaz et raccordement par fiche en option pour le moteur. Document BA 159-EN, édition 2.1, 24.07.2023.
Section-by-Section Technical Breakdown
Identifie les principaux composants de la pompe V-VCB (raccordement vide, sortie d'air d'échappement, bride d'aspiration, entrée/sortie d'air de refroidissement, point de remplissage d'huile, regard d'huile, point de vidange d'huile, plaque de recommandation d'huile, plaque signalétique, flèche de sens de rotation, moteur d'entraînement, plaque signalétique du moteur, surfaces chaudes >70 °C, carter du séparateur d'huile). La plaque signalétique encode le modèle/la taille, le numéro de série, l'année de construction, le code-barres matriciel, le numéro d'article, la vitesse, la puissance du moteur, le mode de fonctionnement, la capacité de pompage et la pression finale pour 50 Hz et 60 Hz.
- Data plate fields: 1 model/size, 2 serial number, 3 year of construction, 4 data matrix barcode, 5 article number, 6 speed 50/60 Hz, 7 motor output 50/60 Hz, 8 operating mode, 9 pumping capacity 50/60 Hz, 10 final pressure (abs.) 50/60 Hz.
- Barcode encodes material number (MA), production order (PR) and serial number (SC).
- Hot surfaces >70 °C are marked (Q).
La V-VCB dispose d'un microfiltre fin côté aspiration et d'un séparateur huile/brouillard d'huile côté refoulement renvoyant l'huile dans la circulation. Un ventilateur entre le carter de pompe et le moteur assure un refroidissement intensif par air. Un clapet anti-retour intégré empêche la ventilation du système évacué après l'arrêt. La pompe est entraînée via un accouplement par un moteur standard monophasé ou triphasé bridé. Une variante avec clapet de ballast à gaz empêche la condensation de vapeur d'eau à l'intérieur de la pompe à température de service.
- Nominal pumping capacity with free intake: 20 m³/h (VCB 20) and 23 m³/h (VCB 25) at 50 Hz.
- Continuous vacuum intake pressure ranges: 50 Hz: 2 to 200 mbar (abs.); 60 Hz: 2 to 150 mbar (abs.).
- When evacuating closed systems, the volume to be evacuated must be no more than 2 % of the nominal pumping capacity.
- Frequent switching (approx. 10 times per hour) or high ambient/inlet temperatures may exceed the excess-temperature limit of motor winding and bearings; contact manufacturer.
- If installed in the open air, protect the unit from environmental influences (e.g. protective roof).
Spécifie les conditions d'installation : accès libre de tous les côtés, grilles de ventilation non obstruées, espace suffisant pour les tuyaux et la maintenance (au moins 30 cm autour de la machine), absence de vibrations externes, pas d'air d'échappement chaud d'autres machines dans le système de refroidissement, bonne ventilation de la pièce et accessibilité de la bride d'aspiration, du point de remplissage d'huile, du regard d'huile, de la vidange d'huile et du carter du séparateur d'huile. La machine doit être installée horizontalement avec une inclinaison max. de 1° dans toutes les directions, sécurisée contre le basculement/la chute, sur un sol plan capable de supporter son poids.
- Maintain at least 30 cm free space around the machine for maintenance.
- Max. inclination: 1° in all directions.
- Cooling air inlets and outlets must be at least 15 cm from adjacent walls; cooling air must not be recirculated.
- Ambient temperature: min. +5 °C, max. +40 °C.
- Output reduction is noticeable when installed at more than 1000 m above sea level; contact manufacturer.
- The non-return valve must not be removed.
Couvre le raccordement de la tuyauterie d'aspiration et d'échappement. L'orifice d'air d'échappement ne doit pas être fermé ni restreint ; aucun filtre ne doit être installé côté air d'échappement ; les contre-pressions côté échappement ne sont admissibles que jusqu'à +100 mbar ; éviter l'accumulation de liquides dans la conduite d'échappement. Retirer le bouchon factice à la sortie d'air d'échappement avant le raccordement. Visser les tuyaux uniquement à la main et utiliser des raccords flexibles si nécessaire.
- Maximum permissible back pressure: +100 mbar.
- No filter on the exhaust air side.
- Remove blind plug on vacuum connection and dummy plug at exhaust air outlet before connecting.
- Pumping capacity is reduced if the inlet pipe is too narrow and/or too long.
L'installation électrique doit être réalisée par un électricien qualifié conformément à EN 60204. L'exploitant doit installer un interrupteur principal et un interrupteur de protection du moteur. Les données du moteur doivent correspondre au réseau (type de courant, tension, fréquence, courant admissible). Les moteurs sont conformes à DIN EN 60034, classe de protection IP 55 et classe d'isolation F. Le schéma de raccordement se trouve dans la boîte à bornes du moteur (absent pour la version avec raccordement par fiche).
- Voltage tolerance: ±5 % of nominal value unless otherwise stated on motor data plate.
- Frequency tolerance: ±2 % unless otherwise stated on motor data plate.
- Direction of rotation must match the arrow on the motor flange.
- Recommended: motor protection circuit breakers with delayed switch off to accommodate temporary excess current at cold start.
Avant la mise en service, vérifier l'absence de dommages de transport/montage, une position horizontale sûre, des raccordements de tuyaux corrects et étanches, des raccords vissés et bridés serrés, une installation électrique conforme au schéma, une ventilation de pièce adéquate, un remplissage d'huile et un niveau vérifié, une pompe et des conduites nettoyées, et le fonctionnement des accessoires en option. Contrôler le sens de rotation avec un indicateur de séquence de phases (champ tournant horaire) ; démarrage bref max. deux secondes ; en regardant le ventilateur du moteur, il doit tourner dans le sens antihoraire. Après correction du sens, faire fonctionner 2 minutes et compléter l'huile jusqu'au bord supérieur du regard, en répétant jusqu'à ce que toutes les conduites d'huile soient remplies.
- Brief start for rotation check: max. two seconds.
- Correct rotation: anti-clockwise when looking at the motor fan.
- Keep a distance of 1 m from outlet and inlet connections during rotation check.
- Filling point must not be open when the pump is running.
- Top up oil after 2 minutes of running until all oil pipes are filled.
Pendant le fonctionnement, le niveau d'huile doit être contrôlé quotidiennement dans le regard. Les fuites ou le brouillard d'huile visible dans l'air d'échappement nécessitent une détermination immédiate de la cause ; l'élément séparateur d'huile doit être remplacé en temps utile et l'huile complétée en temps utile.
- Check oil level daily.
- If leaks occur or exhaust air contains visible oil mist, determine cause immediately.
- Replace oil separator element in good time.
La mise hors service nécessite la déconnexion de l'alimentation, la sécurisation contre le redémarrage, la fermeture des dispositifs d'arrêt si disponibles, la mise à pression atmosphérique par ouverture lente des conduites d'aspiration et de pression, le retrait des tuyaux et flexibles, et l'obturation des tubulures d'entrée/sortie avec des bouchons aveugles ou une feuille adhésive. Pour la remise en service, vérifier l'état de la machine (propreté, câblage) et vidanger les agents de conservation.
- Disconnect and secure against unexpected restart before decommissioning.
- Depressurise slowly by opening suction and pressure lines.
- Seal inlet and outlet stubs with blind plugs or adhesive foil.
- Drain preserving agents before recommissioning.
Couvre la garantie de la sécurité de fonctionnement, le tableau de maintenance, la préparation à la maintenance, le nettoyage de la pompe à vide, le nettoyage du filtre à air, l'huile de lubrification (remplissage et vidange), l'évacuation de l'huile, le moteur et l'accouplement, la réparation/service et les pièces de rechange. La viscosité de l'huile doit être conforme à ISO VG 46 selon DIN ISO 3448. L'élément séparateur d'huile doit être changé lorsqu'il est sale. Les caoutchoucs d'accouplement doivent être remplacés lorsqu'ils sont usés.
- Oil viscosity: ISO VG 46 as per DIN ISO 3448.
- Clean ventilation slots to maintain cooling.
- Change oil separator element when dirty.
- Replace worn coupling rubbers.
- Repairs only by authorised workshops using original spare parts.
Section des données techniques référencée pour le poids, le niveau de pression acoustique et d'autres données de performance. Les valeurs spécifiques sont fournies dans la fiche technique D 159 et sur la plaque signalétique.
- Refer to chapter 10 for weight and sound pressure level.
- Data sheet D 159 contains technical data and characteristic curves.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| La température ambiante et d'aspiration doit être comprise entre 5 et 40 °C. p.8 ↗ | Operation outside this range requires consultation with the manufacturer; otherwise overheating or oil viscosity issues may occur. | V-VCB 20 | 25 |
| La contre-pression maximale admissible côté échappement est de +100 mbar. p.8 ↗ | Exceeding this limit can cause impermissible pressure, component damage or injury; exhaust lines must be sized accordingly. | V-VCB 20 | 25 |
| Plages de pression d'aspiration en vide continu : 50 Hz : 2 à 200 mbar (abs.) ; 60 Hz : 2 à 150 mbar (abs.). p.16 ↗ | Continuous operation outside these ranges risks oil leaking through the outlet opening. | V-VCB 20 | 25 |
| Capacité de pompage nominale avec aspiration libre : 20 m³/h (VCB 20) et 23 m³/h (VCB 25) à 50 Hz. p.16 ↗ | Used for sizing; actual capacity depends on intake pressure per data sheet D 159. | V-VCB 20 and V-VCB 25 respectively |
| Lors de l'évacuation de systèmes fermés, le volume à évacuer ne doit pas dépasser 2 % de la capacité de pompage nominale. p.16 ↗ | Larger volumes require a different pump or method to avoid oil leakage and overheating. | V-VCB 20 | 25 |
| Inclinaison max. en fonctionnement : 1° dans toutes les directions. p.17 ↗ | The machine must be set up horizontally; otherwise lubrication and operation may be impaired. | V-VCB 20 | 25 |
| Les entrées et sorties d'air de refroidissement doivent être à au moins 15 cm des parois adjacentes. p.17 ↗ | Ensures sufficient cooling air flow; otherwise overheating and reduced performance may occur. | V-VCB 20 | 25 |
| Pour la maintenance, prévoir un espace d'au moins 30 cm autour de la machine. p.17 ↗ | Allows access to oil filling point, sight glass, oil drain and separator housing. | V-VCB 20 | 25 |
| Tolérance de tension du moteur : ±5 % de la valeur nominale ; tolérance de fréquence : ±2 % sauf indication contraire sur la plaque signalétique du moteur. p.19 ↗ | Mains conditions must be within these tolerances to avoid loss of power or damage. | V-VCB 20 | 25 |
| Les moteurs sont conformes à DIN EN 60034, classe de protection IP 55 et classe d'isolation F. p.19 ↗ | Suitable for indoor industrial environments; for outdoor installation, additional protection (e.g. protective roof) is required. | V-VCB 20 | 25 |
| Sens de rotation correct : antihoraire en regardant le ventilateur du moteur ; vérifier avec un indicateur de séquence de phases (champ tournant horaire). p.21 ↗ | Wrong rotation can cause injury and machine damage; brief start max. two seconds for check. | V-VCB 20 | 25 |
| La viscosité de l'huile doit être conforme à ISO VG 46 selon DIN ISO 3448. p.26 ↗ | Using incorrect oil viscosity can cause overheating, insufficient pumping capacity or final pressure issues. | V-VCB 20 | 25 |
| Contrôler le niveau d'huile quotidiennement dans le regard. p.21 ↗ | Low oil level can damage the pump; leaks or visible oil mist require immediate action. | V-VCB 20 | 25 |
| Température de stockage : -10 °C à +60 °C ; humidité relative de l'air max. 80 % ; stockage dans un endroit sec, sans poussière, sans vibrations et protégé du rayonnement solaire ; fermer les ouvertures de manière étanche à l'air. p.13 ↗ | Improper storage can damage the machine; for long-term storage (>3 months) use preservation oil. | V-VCB 20 | 25 |
| La machine ne doit pas être stockée plus de 6 mois. p.13 ↗ | Longer storage requires special measures; see Info I 150. | V-VCB 20 | 25 |
| Une réduction de puissance est perceptible en cas d'installation à plus de 1000 m au-dessus du niveau de la mer. p.17 ↗ | Contact manufacturer for high-altitude installations. | V-VCB 20 | 25 |
| Aucun filtre ne doit être installé côté air d'échappement. p.18 ↗ | A filter would increase back pressure and may cause impermissible pressure or damage. | V-VCB 20 | 25 |
| Le clapet anti-retour ne doit pas être retiré. p.17 ↗ | Removing it would allow the evacuated system to ventilate after shutdown. | V-VCB 20 | 25 |
| Si la machine est restée inactive plus de deux minutes, la conduite raccordée doit être mise à la pression atmosphérique. p.15 ↗ | Prevents oil backflow or other issues after shutdown. | V-VCB 20 | 25 |
| Une commutation fréquente à environ 10 fois par heure ou des températures ambiantes/d'aspiration plus élevées peuvent dépasser la limite de surchauffe de l'enroulement du moteur et des roulements. p.16 ↗ | Contact manufacturer for such operating conditions. | V-VCB 20 | 25 |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.32 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.32 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.32 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.32 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC 60947-4-1) | |
| Machine is switched off by the motor protection switch p.32 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the inlet temperature | Chapter 2.4 |
| Machine is switched off by the motor protection switch p.32 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 46 as per DIN ISO 3448 | Chapter 7.6 |
| Machine is switched off by the motor protection switch p.32 ↗ | The oil separator element is dirty. | Change the oil separator element | Chapter 7.7 |
| Machine is switched off by the motor protection switch p.32 ↗ | The back pressure in the exhaust line is too high | Check the hose and/or the pipe | Chapter 5.3 |
| Pumping capacity is insufficient p.32 ↗ | The inlet pipe is too long or too narrow | Check the hose and/or the pipe | Chapter 5.3 |
| Pumping capacity is insufficient p.32 ↗ | Leak on the inlet side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Pumping capacity is insufficient p.32 ↗ | The intake filter is dirty | Clean or replace the intake filter | Chapter 7.5 |
| Final pressure (max. vacuum) is not reached p.33 ↗ | Leak on the inlet side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Final pressure (max. vacuum) is not reached p.33 ↗ | Incorrect oil viscosity | The oil viscosity must comply with ISO VG 46 as per DIN ISO 3448 | Chapter 7.6 |
| Machine gets too hot p.33 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.4 |
| Machine gets too hot p.33 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Machine gets too hot p.33 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.4 |
| Machine gets too hot p.33 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 46 as per DIN ISO 3448 | Chapter 7.6 |
| Machine gets too hot p.33 ↗ | The oil separator element is dirty. | Change the oil separator element | Chapter 7.7 |
| Machine gets too hot p.33 ↗ | The back pressure in the exhaust line is too high | Check the hose and/or the pipe | Chapter 5.3 |
| Exhaust air contains visible oil mist p.33 ↗ | The oil separator element is not inserted correctly. | Check that it is correctly seated | Chapter 7.7 |
| Exhaust air contains visible oil mist p.33 ↗ | Unsuitable oil is being used | Use suitable types | Chapter 7.6 |
| Exhaust air contains visible oil mist p.33 ↗ | The oil separator element is dirty | Change the oil separator element | Chapter 7.7 |
| Exhaust air contains visible oil mist p.33 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.4 |
| Exhaust air contains visible oil mist p.33 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Exhaust air contains visible oil mist p.33 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.2 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | The coupling rubbers worn out | Replace the coupling rubbers | Chapter 7.8.2 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | The pump housing is worn (chatter marks) | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | The vacuum adjustment valve (if available) is vibrating | Replace the valve | Chapter 7.10 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | The blades are damaged | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the inlet temperature | Chapter 2.4 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.33 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 46 as per DIN ISO 3448 | Chapter 7.6 |
| Water in lubricating oil p.34 ↗ | Pump sucks in water | Install water interceptor upstream of the pump | — |
| Water in lubricating oil p.34 ↗ | The pump sucks in more water vapour than is suitable for its water vapour compatibility | Contact the manufacturer for increased gas ballast | Elmo Rietschle Service |
| Water in lubricating oil p.34 ↗ | Pump only works for a short time and therefore does not reach its normal operating temperature | Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil | — |