Induztr
Résumé technique Visionneuse de documents Modèles associés

Rev g paramount ductless enclosures

Technical Reference Summary

Covered Models & Document Scope

Cubre la serie Labconco Paramount® Ductless Enclosure (campana de gases sin conducto), manual pieza n.º 6968600 Rev. G. Modelos: anchos de 2', 3', 4', 5', 6' en variantes de 100-115 V y 208-230 V, incluidas las configuraciones de marco estándar de 22.7"/9.4", marco de 32"/12", marco de 32" x 360° y marco de 35"/12" (p. ej. 6963200, 6963220, 6963300-6963302, 6963320-6963322, 6963400-6963403, 6963420-6963423, 6963501/6963503/6963521/6963523, 6963601/6963603/6963621/6963623). Se envía sin filtros; siete tipos de filtro (HEPA y carbón) se piden por separado.

Section-by-Section Technical Breakdown

pp. 9-12
Requisitos del sitio: soporte, ubicación, extracción y electricidad

Define la estructura de soporte, la ubicación y la evitación de corrientes de aire, la disposición de extracción/soplador, el suministro eléctrico y los requisitos de espacio antes de la instalación. La cabina utiliza un impulsor ECM con 95% de eficiencia energética y normalmente recircula el aire filtrado a la sala; la extracción al exterior requiere el accesorio Canopy Exhaust Connection y un soplador remoto.

  • Supporting structure: base cabinet or stand plus chemically resistant, thick rigid work surface; floor-mounted bench or mobile bench with locking casters acceptable.
  • Avoid high-traffic areas, HVAC diffusers, fans, radiators, doorways and operable windows.
  • All models shipped to operate at 75-80 fpm; can be reset by Safety Officer/certification technician via password-protected menu.
  • If connected to a house exhaust system, an adjustable damper or valve must be installed to control airflow.
  • Standard duplex receptacles should be nearby; iris pass-through ports allow cords through the back.
  • No provision for remote blower control; a wall-mounted switch receptacle may be wired by a qualified electrician.
pp. 11
Datos de caudal de aire, volumen de extracción y ruido por modelo

Tabla de velocidad frontal (60, 80, 100 fpm) frente a volumen de extracción (CFM) y presión sonora (dbA) para cada modelo, con ancho de la cabina, altura de trabajo interna, apertura del marco, profundidad y altura exteriores.

  • 2' models: 85/115/145 CFM at 60/80/100 fpm; 50/54/59 dbA.
  • 3' models (22.7" sash): 130/175/220 CFM; 46/52/56 dbA.
  • 3' models (32" sash): 170/230/285 CFM; 52/57/62 dbA.
  • 4' models (22.7" sash): 175/235/295 CFM; 53/57/62 dbA.
  • 4' models (32" sash): 230/305/380 CFM; 57/62/67 dbA.
  • 5' models: 220/295/370 CFM; 57/62/67 dbA.
  • 6' models: 350/465/580 CFM; 57/61/66 dbA.
pp. 13-15
Desembalaje, superficie de trabajo y montaje de la cabina

Describe el traslado de la cabina sobre su patín, la inspección de daños de transporte y la fijación a una superficie de trabajo nivelada mediante cuatro tornillos de montaje. La parte frontal de la cabina debe alinearse dentro de 0.3" del frente de la superficie de trabajo.

  • Enclosure weight 125-350 lbs (55-152 kg); use mechanical lift truck or floor jack; do not lift by front air foil.
  • Do not move by tilting onto a hand truck.
  • Work surface must be at least as wide as the enclosure, smooth, rigid, non-porous and chemical resistant.
  • Insert four mounting screws leaving minimum 1/8" clearance under the head; stainless surfaces use #10-24 x 3/8" hex washer head screw (Labconco P/N 1885806).
  • Slide rear flange and front air foil flanges under screw heads and tighten.
  • Optional RTV silicone bead seals enclosure to work surface.
pp. 16-18
Instalación de filtros de carbón y HEPA

Enumera los siete tipos de filtro y números de pieza, capacidades de vapor orgánico, reglas de apilamiento y el número de filtros por tamaño de modelo. Los filtros siempre se cargan con la junta hacia arriba y se apilan dos en altura por compartimento.

  • HEPA 6938100: 15" x 18" x 1.5", 99.99% efficient on 0.3 micron.
  • Carbon filters: 6938200 organic vapor 7.5 lbs; 6938201 acid-sulfur 10 lbs; 6938202 ammonia-amine 11 lbs; 6938203 formaldehyde-formalin 10 lbs; 6938204 mixed bed 10 lbs; 6938205 radioisotope 10 lbs.
  • Impregnated carbon filters have 25% organic vapor capacity; mixed bed has 50%.
  • Any combination of two filter types may be used; in clean rooms place HEPA above carbon.
  • 2' = 1 compartment/2 filters/15 lbs; 3' = 2/4/30 lbs; 4' = 3/6/45 lbs; 5' = 3/6/45 lbs; 6' = 4/8/60 lbs.
  • Push stacked filters to the rear stop and close gas-spring cylinders to compress gaskets.
pp. 18-19
Conexión eléctrica, temporizadores de filtro y calentamiento del sensor de vapores

Cubre la conexión del cable de alimentación de 115 V a la entrada IEC, la instalación de un enchufe en unidades de 230 V, el ajuste de los temporizadores de vida/verificación de filtro y el calentamiento inicial de 10-30 minutos del Safety-First Vapor Sensor.

  • 115V units use supplied cord to IEC inlet on rear; 230V units ship without a plug—install per local codes.
  • Set Filter Life Timers in Filter Setup menus using the Paramount Chemical Guide, Appendix E and/or Labconco Specialist.
  • Vapor sensor has a 5V, 0.28W integrated heater; warm up 10-30 minutes with blower running.
  • With new filters, Organic Sensor should read 1300-1500 mV after warm-up.
  • Change all filters when Organic Sensor rises 400-500 mV and display shows 'Replace Filters.'
pp. 19-20
Calibración y validación de la velocidad frontal

Explica el valor preajustado de fábrica de 75-80 fpm, la recalibración mediante el menú de calibración protegido por contraseña, el ajuste del punto de consigna de alarma y el método de medición de la velocidad frontal media.

  • Factory preset face velocity 75-80 fpm; 100 fpm available for special requirements.
  • Airflow alarm preset at 60 fpm; adjust to 10-20 fpm below actual face velocity.
  • Measure with calibrated thermal anemometer at 5" directly below sash handle; readings 6" from ends and every 12".
  • Recalibrate at altitudes above or below 900 feet.
  • Smart-Flow automatically compensates motor speed for filter loading, barometric pressure and temperature.
  • ASHRAE 110-1995 containment rating <0.05 ppm at 4 lpm.
pp. 20
Conexión a un sistema de extracción

Describe la extracción opcional al exterior mediante el Canopy Exhaust Connection que admite conductos de 6", con soporte independiente de los conductos e instalación por un contratista de HVAC.

  • Normal operation recirculates filtered air into the room; canopy not required.
  • Canopy Exhaust Connection accepts 6" diameter ductwork.
  • Exhaust ductwork weight must be supported independently of the enclosure superstructure.
  • Installation by qualified HVAC contractor; consult Labconco for blower sizing.
  • Duct material must match enclosure, procedures and chemical applications.
pp. 21-26
Características de rendimiento y sistemas de seguridad

Describe los perfiles aerodinámicos de contención, el rango de detección del Safety-First Vapor Sensor y la tabla de sensibilidad química, el monitor de caudal Smart-Flow, el impulsor ECM, las alarmas y la pantalla LCD.

  • Safety-First Vapor Sensor optimal detection range 1-10 ppm; primary and secondary sensors.
  • Detects organic solvents, smoke particulates, ammonia, formaldehyde and hydrogen sulfide; does NOT detect mineral acids (HCl, nitric, sulfuric).
  • Early warning at 5-10% remaining filter life: intermittent beep; final warning: constant alarm.
  • ECM impeller 95% energy efficient, located after filters; all Paramounts ≤62 dbA at 80 fpm, most ≤59 dbA.
  • LCD 3" x 1.5" displays filter status, face velocity and alarms.
  • Smart-Flow uses pitot tube and pressure sensor on control board for constant velocity.
pp. 39-50
Mantenimiento rutinario y sustitución de filtros

Proporciona el programa de mantenimiento rutinario, los criterios para sustituir filtros de carbón y HEPA, la prueba de fugas de HEPA, el cambio de velocidad frontal y los procedimientos de sustitución de lámpara, impulsor, placa de control principal y placa del sensor orgánico.

  • Carbon filter replacement determined by vapor sensor alarm, elapsed timer, or chemical guide calculation.
  • HEPA filter replaced when clogged/low airflow or per schedule.
  • HEPA filter leak test procedure included.
  • Fluorescent light, motorized impeller, main control board and organic sensor board replacement procedures.
  • Re-certification and initial certification guidance.
pp. 51-59
Accesorios y pedidos

Enumera superficies de trabajo, soportes, armarios de almacenamiento, transiciones de extracción, sopladores remotos, compuertas de extracción, kits de estante de servicios, kit de bomba de jeringa, tubos detectores y cierres de marco.

  • Work surfaces with deck-mounted valves, gooseneck and cupsink.
  • Base stands, accessory shelves, seismic supports, hydraulic lift base stands.
  • Storage cabinets, exhaust transitions, remote blowers, exhaust dampers.
  • Utility shelf kits and holders, syringe pump kit and detector tubes, sash closures.
pp. 60-62
Solución de problemas

Tabla de problemas, causas y acciones correctivas para alarmas de filtro, alarmas de caudal de aire, fallos de soplador/lámpara y mal funcionamiento del monitor de caudal de aire.

  • Covers 'Replace Filters' continuous and intermittent alarms.
  • Covers 'Check Filters' intermittent alarm.
  • Covers blower will not operate, low face velocity, lights do not work.
  • Covers airflow monitor malfunction (no audible alarm, constant alarm, low airflow).

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
Todos los modelos se envían para funcionar a una velocidad frontal de 75-80 fpm; se puede reajustar mediante un menú protegido por contraseña. p.10 ↗ Default commissioning setpoint; verify with thermal anemometer before use. whole series
Alarma de caudal de aire preajustada a 60 fpm; ajustar a 10-20 fpm por debajo de la velocidad frontal real. p.19 ↗ Set alarm after calibration to avoid nuisance alarms while maintaining protection. whole series
Medición de velocidad frontal: anemómetro térmico calibrado, 5" directamente por debajo del tirador del marco, lecturas a 6" de los extremos y cada 12". p.19 ↗ Standardized validation method for certification. whole series
Se requiere recalibración a altitudes superiores o inferiores a 900 pies. p.19 ↗ Site altitude affects pressure sensor and face velocity; recalibrate after installation. whole series
El sensor orgánico debe leer 1300-1500 mV con filtros nuevos tras un calentamiento de 10-30 minutos con el soplador en marcha. p.18 ↗ Baseline for sensor health; replace filters when reading rises 400-500 mV and 'Replace Filters' appears. whole series
Rango de detección óptimo del Safety-First Vapor Sensor: 1-10 ppm; no detecta ácidos minerales (HCl, nítrico, sulfúrico). p.24 ↗ Use alternative detection (mineral acid sensor or sampling tubes) for acid applications. whole series
Los filtros de carbón impregnado tienen 25% de capacidad de vapor orgánico; el lecho mixto tiene 50%. p.17 ↗ For solvent+acid service, use one organic vapor filter plus one impregnated acid filter. filter selection
Recuento de filtros: 2'=2 filtros/15 lbs; 3'=4/30 lbs; 4'=6/45 lbs; 5'=6/45 lbs; 6'=8/60 lbs de peso total de vapor orgánico. p.17 ↗ Determines spare filter inventory and filter life calculation. model sizes
El filtro HEPA 6938100 es 99.99% eficiente en 0.3 micras; dimensiones 15" x 18" x 1.5". p.17 ↗ Particulate containment specification for powder work. HEPA option
Peso de la cabina 125-350 lbs (55-152 kg); no levantar por el perfil aerodinámico frontal. p.13 ↗ Rigging and installation planning; use mechanical lift or floor jack. whole series
El frente de la cabina debe alinearse dentro de 0.3" del frente de la superficie de trabajo; los tornillos de montaje dejan un espacio mínimo de 1/8" bajo la cabeza. p.14 ↗ Ensures proper air foil function and secure mounting. whole series
Las superficies de trabajo de acero inoxidable utilizan tornillo de cabeza hexagonal con arandela n.º 10-24 x 3/8", P/N de Labconco 1885806. p.15 ↗ Correct fastener for mounting enclosure to stainless surface. stainless work surfaces
El Canopy Exhaust Connection admite conductos de 6" de diámetro; el peso de los conductos debe soportarse de forma independiente. p.20 ↗ Outside exhaust installation requires separate duct supports and HVAC contractor. exhaust option
El impulsor ECM tiene 95% de eficiencia energética y está situado después de los filtros; todos los Paramount son ≤62 dbA a 80 fpm, la mayoría ≤59 dbA. p.25 ↗ Noise planning and intrinsically safe design (contaminated air filtered before impeller). whole series
Clasificación de contención ASHRAE 110-1995 <0.05 ppm a 4 lpm. p.20 ↗ Validated containment performance for operator protection. whole series
Calentamiento del sensor de vapores: calentador integrado de 5V, 0.28W; 10-30 minutos con el soplador activado. p.18 ↗ Allow warm-up before relying on sensor readings after shipment or filter change. whole series
Carga de filtros: siempre con la junta hacia arriba; apilar dos en altura por compartimento; en salas limpias, HEPA por encima del carbón. p.17 ↗ Correct orientation prevents bypass and contamination. filter installation
Las unidades de 230 V se envían sin enchufe; instalar el enchufe adecuado según los códigos locales. p.18 ↗ Electrical contractor must supply plug for 208-230V models. 208-230V models

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
"Replace Filters" continuous alarm occurs p.66 ↗ Improper final time programmed and display reads "Replace Filters-t", (t = time) See Chapters 3 and 5 to properly set the Filter Final Life Timer. Chapter 8
Organic sensor alarms and display reads "Replace Filters-s", (s = organic sensor) p.66 ↗ Organic sensor has detected filter breakthrough. Replace filters immediately. A spare set of filters should always be on hand. Consult Chapters 3, 4, and 5, the Labconco Specialist, and the Chemical Guide for estimated filter life based on specific chemical use. Always limit chemical use, cover up chemicals when not in use and turn off blower to preserve filter life. Chapter 8
"Mute" will not stay operational p.66 ↗ The "Mute" alarm can only be off for 5 minutes and must be pushed every 5 minutes until the filters have been replaced. See Chapters 3, 5 & 6. Chapter 8
"Check Filters" intermittent alarm occurs frequently p.66 ↗ Improper check time programmed and display reads "Check Filters-t", (t = time) See Chapters 3 and 5 to properly set the Filter Check Life Timer. Chapter 8
Replace filters intermittent alarm occurs p.67 ↗ Organic sensor alarms intermittently and display reads "Replace Filters-s", s = organic sensor; organic sensor has detected filter breakthrough and only 5-10% of filter life remains. Replace filters with a spare set of filters stored. Consult Chapters 3, 4, and 5, Filter Specialist, and Chemical Guide for filter life based on specific chemical use. Always limit chemical use, cover up chemicals and turn off blower when not in use to preserve life. Chapter 8
Replace filters intermittent alarm occurs p.67 ↗ Carbon filter loaded with chemicals. Replace carbon filter. Chapter 8
Contaminants outside of enclosure p.67 ↗ Improper user techniques for the enclosure. See "Validate the Enclosure" Chapter 3 and "Safety Precautions" Chapter 4 sections in the manual. Chapter 8
Contaminants outside of enclosure p.67 ↗ Restriction of the baffle air slots or blockage of the exhaust outlet. Remove obstruction to ensure that all air slots and the exhaust outlet are unobstructed. Chapter 8
Contaminants outside of enclosure p.67 ↗ External factors are disrupting the enclosure airflow patterns or acting as a source of contamination. See "Location Requirements" Chapter 2, "Validate the Enclosure" Chapter 3, and "Safety Precautions" Chapter 4 sections of this manual. Chapter 8
Contaminants outside of enclosure p.67 ↗ Enclosure has improper face velocity. Have enclosure certified per Chapter 6 and check exhaust system. Check carbon filters and replace if necessary. Enclosure should have an average face velocity of 60-100 fpm. Chapter 8
Blower will not operate p.67 ↗ Unit not plugged into outlet. Plug the enclosure into appropriate electrical service. Chapter 8
Blower will not operate p.67 ↗ Circuit breaker(s) or Ground Fault Interrupter. Reset circuit breaker. Chapter 8
Blower will not operate p.67 ↗ Blower wiring is disconnected. Inspect blower wiring. Chapter 8
Blower will not operate p.67 ↗ Blower switch is defective. Replace membrane switch on control panel. Chapter 8
Blower will not operate p.67 ↗ Motorized impeller is defective. Replace motorized impeller. See Chapter 6. Chapter 8
Low face velocity p.67 ↗ Enclosure sash not closed. Close sash to the lowest position. Chapter 8
Low face velocity p.67 ↗ HEPA filter clogged. Replace HEPA filter. Chapter 8
Blower and lights will not operate p.67 ↗ Unit not plugged into outlet. Plug enclosure into appropriate electrical service. Chapter 8
Blower and lights will not operate p.67 ↗ Circuit breaker(s) tripped. Reset or replace circuit breaker. Chapter 8
Lights do not work p.68 ↗ Lamp not installed properly. Inspect lamp installation. Chapter 8
Lights do not work p.68 ↗ Lamp wiring disconnected. Inspect lamp wiring. Chapter 8
Lights do not work p.68 ↗ Defective lamp. Replace lamp. Chapter 8
Lights do not work p.68 ↗ Light switch is defective. Replace membrane switch on control panel. Chapter 8
Lights do not work p.68 ↗ Defective electronic ballast. Replace ballast. Chapter 8
Airflow monitor malfunction - No audible alarm. p.68 ↗ Alarm has been temporarily silenced using "mute" button. Wrong alarm set point. Airflow monitor alarm is preset at 60 fpm. Repeat calibration steps outlined in this manual in Chapter 3, Chapter 5 and Chapter 6. Chapter 8
Airflow monitor malfunction - Constant audible alarm. p.68 ↗ Check airflow and calibration of airflow monitor. See Chapter 5 & 6. Chapter 8
Airflow monitor malfunction - Continuous alarm. p.68 ↗ Check the face velocity of the enclosure as the airflow of the system may have changed. If incorrect, follow the calibration steps in Chapters 3, 5 and 6. The carbon filter pre-filter or HEPA filter may have become loaded. Check the face velocity of the enclosure as the airflow of the system may have changed. If incorrect, follow the calibration steps in Chapters 3, 5 and 6. The carbon filter pre-filter or HEPA filter may have become loaded. Chapter 8
Airflow monitor malfunction - Low airflow. p.68 ↗ Check airflow and reset airflow monitor. See Chapter 5 & 6. Look for filter blockage or paper debris. Chapter 8