Induztr
Résumé technique Visionneuse de documents Modèles associés

Rev j xpert nano enclosures user manual

Technical Reference Summary

Covered Models & Document Scope

Couvre la série Labconco XPert® Nano Enclosure en largeurs 2', 3', 4', 5' et 6'. Les modèles 2'/3'/4' utilisent une ouverture de guillotine de 9,4" et un conduit d'évacuation nominal de 6" ; les modèles 5'/6' utilisent une ouverture de guillotine de 12" et un conduit d'évacuation nominal de 10". Les options comprennent un ioniseur installé en usine, un Guardian Airflow Monitor ou un Guardian 1000 Digital Airflow Monitor, un raccordement d'évacuation à hotte, des ventilateurs déportés, des registres d'évacuation, des filtres accessoires et des tablettes utilitaires. Variantes électriques : 115 V avec cordon d'alimentation et 230 V expédié sans fiche.

Section-by-Section Technical Breakdown

pp. 7-9
Exigences relatives au site, au support, aux vibrations, à la température et à l'humidité

Définit les prérequis pour le site d'installation : niveau, construction solide, alimentation électrique dédiée à proximité, et un banc ou support minimisant les vibrations. Une dérive de température de 1–2 °C est généralement tolérable selon les fabricants de balances. L'humidité doit être maintenue entre 45 et 60 % pour contrôler l'électricité statique, et l'enceinte évite les plastiques pour réduire les surfaces isolantes.

  • Avoid tubular stands or mobile benches that can move when touched.
  • A bench rigidly mounted to floor or wall (not both) may be appropriate.
  • Building corners typically have less vibration than the center.
  • Do not place vibration-producing equipment such as shakers or pumps on the bench.
  • Marble slabs with dampening pads inside the enclosure are an effective low-cost vibration control.
  • Calibrate and verify the balance at least annually; best results when calibrated inside the enclosure at the desired face velocity.
  • Never install balances near radiators or hot plates; avoid direct sunlight on the bench.
  • Maintain humidity between 45 and 60%; a factory-installed ionizer is available to neutralize surface charges.
pp. 9
Exigences relatives à l'emplacement et aux courants d'air

L'enceinte doit être placée de manière à éviter les courants d'air croisés et les turbulences qui perturbent le confinement et les lectures de la balance. Les zones de fort passage, les diffuseurs CVC, les ventilateurs, les radiateurs et les portes ou fenêtres ouvrables doivent être évités. Le dispositif de sectionnement principal doit rester accessible.

  • Avoid high-traffic areas where walking causes air disturbance.
  • Avoid overhead or wall HVAC diffusers, fans, radiators or other air-current-producing lab equipment.
  • Avoid locations next to doorways or windows that may be opened.
  • Do not position the unit so that the main disconnect device is difficult to operate.
pp. 10
Exigences relatives à l'évacuation et au ventilateur

La turbine motorisée intégrée aspire l'air ambiant à travers le filtre ULPA et évacue l'air filtré par le haut. L'évacuation peut être recirculée dans le laboratoire ou canalisée vers l'extérieur via le raccordement d'évacuation à hotte en option et un ventilateur déporté. Des tableaux indiquent le volume d'évacuation, la perte de pression statique, le bruit et la pression statique externe maximale pour chaque largeur à 60, 80 et 100 fpm.

  • 2' model at 60/80/100 fpm: 85/115/145 CFM; initial static pressure loss 0.35–0.41 / 0.48–0.57 / 0.62–0.72 in w.g.; noise 48–53 / 50–56 / 53–58 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • 3' model at 60/80/100 fpm: 130/175/220 CFM; static pressure loss 0.37–0.43 / 0.53–0.62 / 0.68–0.79 in w.g.; noise 48–53 / 53–57 / 58–61 dB(A); max external static pressure 0.15 / 0.11 / 0.08 in w.g.
  • 4' model at 60/80/100 fpm: 175/235/295 CFM; static pressure loss 0.40–0.46 / 0.57–0.66 / 0.76–0.87 in w.g.; noise 49–54 / 58–61 / 62–66 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • 5' model at 60/80/100 fpm: 290/385/480 CFM; static pressure loss 0.38–0.46 / 0.55–0.67 / 0.72–0.85 in w.g.; noise 52–56 / 58–63 / 63–67 dB(A); max external static pressure 0.22 / 0.20 / 0.15 in w.g.
  • 6' model at 60/80/100 fpm: 350/465/580 CFM; static pressure loss 0.46–0.56 / 0.67–0.81 / 0.87–1.03 in w.g.; noise 55–57 / 61–63 / 67–69 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • Weighing and handling nano materials is best done at lower flow rates of 60–70 fpm (0.31–0.36 m/s).
  • If connected directly to a house exhaust system, an adjustable damper or valve must be installed to control airflow, especially when one house system serves multiple filtered enclosures.
pp. 11, 18
Exigences électriques et raccordement

Des prises duplex standard doivent être à proximité. Le modèle 115 V utilise un cordon d'alimentation fourni connecté à l'entrée CEI à l'arrière ; le modèle 230 V est expédié sans fiche et nécessite une fiche appropriée selon les codes locaux. Tous les modèles consomment moins de 5 A. À 50 Hz, le débit d'air maximal du ventilateur est réduit de 17 %.

  • 115 V: connect supplied power cord to IEC electrical supply plug on back of enclosure.
  • 230 V: shipped without plug; install appropriate plug per local electrical specifications and codes.
  • All models use less than 5 amps.
  • At 50 Hz operation, blower maximum airflow is reduced by 17%.
  • All wiring should be performed by a licensed electrician and conform to local codes.
  • Do not use any detachable power cord that is not adequately rated for the unit.
pp. 12-14
Déballage et installation du support/meuble

Les enceintes pèsent de 173 à 443 lbs (78,47 à 200,94 kg) et doivent être déplacées avec un chariot élévateur mécanique, un cric de plancher ou un chariot bas sous le patin d'expédition ; ne pas incliner sur un diable ni soulever par le déflecteur d'air avant. La surface supérieure du support de base se règle de 27,5 à 34,50 pouces (698 à 876 mm) par incréments de 1 pouce (25 mm). La surface de travail intégrale en acier inoxydable se fixe au support avec quatre boulons 1/4"-20 x 2,5".

  • Enclosure weight range: 173 to 443 lbs (78.47 to 200.94 kg).
  • Do not move the enclosure by tilting it onto a hand truck.
  • Do not lift by the front air foil.
  • Base stand height adjustable 27.5 to 34.50 inches (698 to 876 mm) in 1-inch (25 mm) increments.
  • Leg extensions attach with 5/16"-18 x 2-1/4 inch (57 mm) bolts, flatwasher, lockwasher and acorn nut; select the same height hole for each leg.
  • Work surface mounts with four 1/4"-20 x 2.5 inch (63 mm) hex head bolts, nuts and washers; front edge flush with stand front edge.
  • Use a carpenter level to adjust leveling feet in both planes.
pp. 15-17
Raccordement au système d'évacuation (en option)

Les modèles 2', 3' et 4' acceptent un conduit nominal de 6" (6,06" DI) et les modèles 5' et 6' acceptent un conduit nominal de 10" (10,06" DI). Sur les tailles 2'/3'/4', le raccordement d'évacuation est expédié non installé sur le dessus et se fixe avec les vis fournies. Le poids de la gaine doit être supporté indépendamment de la superstructure de l'enceinte.

  • 2', 3', 4' models: 6" nominal exhaust duct, 6.06" ID.
  • 5', 6' models: 10" nominal exhaust duct, 10.06" ID.
  • Exhaust connection on 2'/3'/4' ships uninstalled on top; fasten with screws provided.
  • The weight of the exhaust ductwork system must be supported independently of the enclosure superstructure or damage may occur.
  • Exhaust system should be installed by a qualified HVAC contractor.
  • Selected exhaust duct material should match the enclosure, procedures and chemical applications.
pp. 18-19
Réglage de la vitesse frontale par ajustement du contrôle de vitesse

Le contrôle de vitesse derrière le panneau avant ajuste la vitesse frontale de 60 à 100 fpm. La vitesse frontale moyenne se mesure avec un anémomètre sur deux rangées à travers l'ouverture de la guillotine : lectures à 6" des extrémités et tous les 12", première rangée à 3" sous le déflecteur supérieur de guillotine et seconde rangée à 3" au-dessus de la surface de travail. Les tests de débit d'air Labconco selon ASHRAE 110-1995 ont obtenu une cote de fabrication inférieure à 0,05 ppm à 4 lpm.

  • Face velocity adjustable from 60 to 100 fpm via speed control behind front panel.
  • Containment is maximized within this range; lowest permissible velocity gives least turbulent, quietest operation.
  • Average face velocity readings: two rows, 6" from ends, evenly spaced every 12"; first row 3" down from upper sash foil, second row 3" up from work surface.
  • As-manufactured ASHRAE 110-1995 rating: less than 0.05 ppm at 4 lpm.
  • Face velocity profiles and smoke testing should be performed frequently per the organization's quality system.
pp. 20-24
Caractéristiques de haute performance

Décrit les éléments de conception aérodynamique : déflecteur d'air Clean-Sweep, déflecteur supérieur de guillotine, alimentation supérieure en air de dilution, chicane perforée arrière zonée, déflecteurs d'air à entrée latérale, guillotine en verre de sécurité, ports utilitaires, plénum en dépression, turbine motorisée isolée des vibrations, contrôle de vitesse, manomètre du système de filtration, port d'accès au filtre ULPA, panneau de commande, filtre ULPA, collier d'évacuation en option, raccordement d'évacuation à hotte, ioniseur et tablettes utilitaires.

  • Upper dilution air supply introduces 5 to 7 percent of required air volume through the upper dilution air supply.
  • Zoned rear perforated baffle has three zones with increasingly more open area at the bottom to form laminar airflow.
  • Safety glass sash has a wiping seal and spring-loaded latch; 5' and 6' units use a gas spring assist instead of the latch.
  • ULPA filter rated to remove 99.999% of all particles 0.12 micron in size.
  • Plenum and ULPA filter are jacketed by negative pressure; leaks are recaptured and refiltered.
  • True bag-in/bag-out ULPA filter disposal system protects worker from hazardous powders and particulates.
  • Optional ionizer cannot be installed after manufacture.
  • Filter system pressure gauge indicates total system pressure across filter and pressurized plenum to help predict filter loading.
pp. 27-28
Procédures de travail quotidiennes de routine

Couvre la planification, le démarrage, le chargement, les techniques de travail, la purge finale, le déchargement et l'arrêt. Laisser l'enceinte fonctionner sans obstruction pendant 1 minute au démarrage et après le chargement ; après le travail, laisser 2 à 3 minutes de purge sans perturbation avant d'arrêter le ventilateur.

  • Turn on exhaust system and light; only raise sash for loading and cleaning.
  • Check baffle air slots for obstructions.
  • Allow enclosure to operate unobstructed for 1 minute before work.
  • After loading, wait one minute to purge airborne contaminants.
  • Upon completion, allow enclosure to operate for two to three minutes undisturbed before shutting down blower.
  • Surface decontaminate objects in contact with contaminated material before removal; cover open trays, weigh vessels or containers before removal.
pp. 28
Applications, adéquation et directives du filtre ULPA

Le filtre ULPA convient pour la pesée et la manipulation de poudres, de particules non volatiles, de poudres dangereuses et de matériaux biologiquement dangereux. Il assure la protection du personnel et de l'environnement mais pas la protection du produit contre la contamination environnementale. Les gaz ou vapeurs nécessitent une ventilation vers l'extérieur. La surface du filtre est fragile et ne doit pas être touchée ni percée.

  • Suitable for weighing and handling of powders and release of nonvolatile particulates.
  • Provides personal and environmental protection from particulate matter, hazardous powders and biohazardous materials.
  • Not for operations requiring sample protection from environmental contamination.
  • ULPA filters are only effective for entrapment of particulate matter; gases or vapors require outside ventilation.
  • If a ULPA filter is suspected damaged, do not use the enclosure; contact a certification agency or Labconco.
  • For powders and particulates follow the ULPA Filter Bag-In/Bag-Out procedure in Chapter 6; for biohazardous materials follow the Decontamination Procedure.
pp. 25, 43
Ioniseur en option

L'ioniseur installé en usine contrôle la charge statique sur les surfaces à l'intérieur de l'enceinte. Sa décharge est située à la face avant de la surface de travail, à l'abri des contaminants et du nettoyage. Les émetteurs ont une durée de vie finie et peuvent nécessiter un remplacement.

  • Ionizer floods the work area with positive and negative ions to neutralize static charges on non-conductive items.
  • Discharge located at the front face of the work surface.
  • Ionizer cannot be installed after manufacture.
  • Emitters have a finite life and may require replacement.
pp. 27-44
Calendrier de maintenance de routine

Fournit un calendrier pour la maintenance de routine incluant la décontamination, la détermination du moment de remplacer les filtres ULPA, l'installation de filtre en sac/en sac, les tests d'étanchéité des filtres, le réglage de la vitesse frontale d'entrée et l'étalonnage et l'utilisation des moniteurs de débit d'air.

  • Routine maintenance schedule covers decontamination, filter replacement determination, bag-in/bag-out filter installation, filter leak test, face velocity setting and airflow monitor calibration.
  • Initial certification and re-certification are required.
  • Fluorescent and LED light replacement, motorized impeller replacement, speed control replacement, ionizer maintenance and trace odor carbon filter installation are covered.
pp. 28-31
Remplacement du filtre ULPA, installation en sac/en sac et test d'étanchéité

Décrit la détermination du moment de remplacer les filtres ULPA, l'installation d'un nouveau filtre ULPA selon la procédure en sac/en sac, et les tests d'étanchéité des filtres. Le boulon de serrage du filtre scelle uniformément le filtre au cadre. Les filtres ULPA d'évacuation sont éliminés comme déchets dangereux à l'aide du sac d'élimination.

  • Replace ULPA filter when face velocity falls below acceptable limits established by Safety Officer.
  • Use true bag-in/bag-out procedure for harmful powders and particulates.
  • Filter clamping bolt evenly seals filter to enclosure frame.
  • Exhaust ULPA filters are disposed as hazardous waste; user is responsible for recording material and disposing properly.
  • Filter leak test is part of maintenance.
pp. 33-40
Étalonner et utiliser les moniteurs de débit d'air

Couvre le Guardian Digital 1000 Airflow Monitor et le Guardian Airflow Monitor, y compris la programmation de l'alarme numérique Guardian 1000. Le Guardian 1000 affiche la vitesse frontale, fournit une sortie RS232, un mode de réduction nocturne et des ports de relais auxiliaires. Les étapes d'étalonnage sont décrites au chapitre 6 ou dans le manuel du Digital 1000 Monitor fourni.

  • Guardian 1000 Digital Airflow Monitor displays face velocity value, provides RS232 output, night setback mode and several auxiliary relay ports.
  • Guardian Airflow Monitor continuously monitors airflow with audio/visual alarm for low airflow.
  • Programming the Guardian 1000 Digital Alarm is covered.
  • Calibration steps are in Chapter 6 or the supplied Digital 1000 Monitor Manual.
pp. 40-44
Maintenance de l'éclairage, de la turbine motorisée, du contrôle de vitesse et de l'ioniseur

Couvre le remplacement des lampes fluorescentes et LED, le remplacement de la turbine motorisée, le remplacement du contrôle de vitesse, la maintenance de l'ioniseur en option et l'installation du filtre à charbon pour les odeurs à l'état de traces.

  • Fluorescent light replacement and LED light replacement procedures.
  • Motorized impeller replacement procedure.
  • Speed control replacement procedure.
  • Maintenance on the optional ionizer.
  • Trace odor carbon filter installation.
pp. 45-48
Accessoires pour l'enceinte Nano

Liste les options d'accessoires : Guardian Airflow Monitors, raccordement d'évacuation à hotte, ventilateurs déportés, registres d'évacuation et filtres accessoires. Le raccordement d'évacuation à hotte comprend un adaptateur de transition d'évacuation en acier revêtu d'époxy pour conduit nominal de 6" sur les tailles 2'/3'/4' et de 10" sur les tailles 5'/6'.

  • Guardian Airflow Monitors available as accessories.
  • Canopy Exhaust Connection includes epoxy-coated steel exhaust transition adapter.
  • 2', 3', 4' sizes use 6" nominal duct; 5', 6' sizes use 10" nominal duct.
  • Remote blowers and exhaust dampers available.
  • Accessory filters available.
pp. 53-64
Pièces de rechange, dimensions et spécifications

L'annexe A liste les pièces de rechange, l'annexe B fournit les dimensions pour tous les modèles, l'annexe C fournit les spécifications électriques et environnementales, et l'annexe D est un tableau récapitulatif.

  • Appendix A: Replacement Parts.
  • Appendix B: Dimensions for different models.
  • Appendix C: Specifications for electrical and environmental conditions.
  • Appendix D: Quick Chart.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
Filtre ULPA certifié au moins 99,999 % efficace pour les particules de 0,12 micron. p.5 ↗ Suitable for containment of hazardous powders and biohazardous particulates; not for gases or vapors. whole series
Vitesse frontale réglable de 60 à 100 fpm via le contrôle de vitesse derrière le panneau avant. p.18 ↗ Set within this range for containment; lowest permissible velocity gives least turbulent, quietest operation. whole series
Pour les procédures de pesée, la vitesse frontale doit être de 60–100 fpm ; pour les procédures biologiquement dangereuses, de 75–105 fpm. p.54 ↗ Select face velocity according to application; verify with anemometer. whole series
La pesée et la manipulation de nanomatériaux se font de préférence à des débits plus faibles de 60–70 fpm (0,31–0,36 m/s). p.10 ↗ Use lower face velocity for nanoparticle work to optimize containment. whole series
Les modèles 2', 3', 4' acceptent un conduit d'évacuation nominal de 6" (6,06" DI) ; les modèles 5', 6' acceptent un conduit nominal de 10" (10,06" DI). p.15 ↗ Ductwork and canopy exhaust connection must match model width. 2'/3'/4' vs 5'/6' models
Modèle 2' à 60 fpm : 85 CFM, perte de pression statique initiale 0,35–0,41 in w.g., bruit 48–53 dB(A), pression statique externe max 0,20 in w.g. p.10 ↗ Use for blower sizing and exhaust system design. 2' model
Modèle 6' à 100 fpm : 580 CFM, perte de pression statique initiale 0,87–1,03 in w.g., bruit 67–69 dB(A), pression statique externe max 0,13 in w.g. p.10 ↗ Highest airflow and pressure loss of the series; blower must be sized accordingly. 6' model
Tous les modèles utilisent moins de 5 ampères. p.18 ↗ Standard duplex receptacle circuit is adequate; verify local codes. whole series
À 50 Hz, le débit d'air maximal du ventilateur est réduit de 17 %. p.18 ↗ Account for reduced airflow when sizing blower and setting face velocity in 50 Hz regions. whole series
Plage de poids de l'enceinte : 173 à 443 lbs (78,47 à 200,94 kg). p.12 ↗ Use mechanical lift truck, floor jack or low dolly under shipping skid; do not tilt onto hand truck or lift by front air foil. whole series
Surface supérieure du support de base réglable de 27,5 à 34,50 pouces (698 à 876 mm) par incréments de 1 pouce (25 mm). p.14 ↗ Select optimum working height; use same height hole for each leg. models with base stand
La surface de travail se fixe avec quatre boulons à tête hexagonale 1/4"-20 x 2,5 pouces (63 mm), écrous et rondelles ; les extensions de pied utilisent des boulons 5/16"-18 x 2-1/4 pouces (57 mm). p.14 ↗ Use specified hardware for assembly; tighten after all four bolts started. models with base stand
L'alimentation supérieure en air de dilution introduit 5 à 7 pour cent du volume d'air requis. p.23 ↗ Part of total airflow; account for when measuring face velocity. whole series
Mesure de la vitesse frontale moyenne : deux rangées, lectures à 6" des extrémités et tous les 12", première rangée à 3" sous le déflecteur supérieur de guillotine, seconde rangée à 3" au-dessus de la surface de travail. p.18 ↗ Standardized method for certifying face velocity. whole series
Cote ASHRAE 110-1995 de fabrication : inférieure à 0,05 ppm à 4 lpm. p.18 ↗ Baseline containment performance; field testing available through Labconco certified contractor. whole series
Maintenir l'humidité entre 45 et 60 % pour contrôler l'électricité statique. p.8 ↗ Static charges can cause weighing errors and particulate attraction; ionizer available as factory option. whole series
Une dérive de température de 1–2 °C est généralement tolérable selon les fabricants de balances. p.8 ↗ Avoid heating sources and direct sunlight; validate through Operational Qualification protocol. whole series
Laisser le ventilateur en marche au moins une minute après le travail ; laisser 2 à 3 minutes de purge sans perturbation avant l'arrêt. p.26 ↗ Ensures airborne contaminants are purged before blower is turned off. whole series
L'enceinte doit être recertifiée à chaque intervention ou au moins annuellement par la suite. p.25 ↗ Maintain certification schedule for continued safe operation. whole series
En cas de raccordement direct à un système d'évacuation du bâtiment, un registre ou une vanne réglable doit être installé pour contrôler le débit d'air. p.10 ↗ Required especially when one house system serves multiple filtered enclosures. models with house exhaust connection

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
Contaminants outside of enclosure. p.54 ↗ Improper user techniques for the enclosure. See "Certifying the Enclosure" Chapter 3 and "Safety Precautions" Chapter 4 sections in the manual. (Ref. Appendix D). Chapter 8
Contaminants outside of enclosure. p.54 ↗ Restriction of the baffle air slots or blockage of the exhaust outlet. Remove obstruction to ensure that all air slots and the exhaust outlet are unobstructed. Chapter 8
Contaminants outside of enclosure. p.54 ↗ External factors are disrupting the enclosure airflow patterns or acting as a source of contamination. See "Location Requirements" Chapter 2, "Certifying the Enclosure" Chapter 3, and "Safety Precautions" Chapter 4 sections of this manual. (Ref. Appendix D). Chapter 8
Contaminants outside of enclosure. p.54 ↗ Enclosure has improper face velocity. Have enclosure certified and check exhaust system. Check filters for loading. Adjust enclosure speed control. Enclosure should have an average face velocity of 60-100 fpm for weighing procedures and 75-105 fpm for biohazardous procedures. Chapter 8
Blower won't operate. p.54 ↗ Unit not plugged into outlet. Plug the enclosure into appropriate electrical service. Chapter 8
Blower won't operate. p.54 ↗ Circuit breaker(s) or Ground Fault Interrupter. Reset circuit breaker. Chapter 8
Blower won't operate. p.54 ↗ Blower wiring is disconnected. Inspect blower wiring. Chapter 8
Blower won't operate. p.54 ↗ Blower switch is defective. Replace switch. Chapter 8
Blower won't operate. p.54 ↗ Motorized impeller or blower is defective. Replace motorized impeller or blower. See Chapter 6. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ Enclosure sash not closed. Close sash to the lowest position. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ ULPA filter clogged. Replace ULPA filter or increase speed. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ Carbon filter loaded with chemicals. Replace carbon filter. Chapter 8
Blower and lights won't operate. p.54 ↗ Unit not plugged into outlet. Plug enclosure into appropriate electrical service. Chapter 8
Blower and lights won't operate. p.54 ↗ Circuit breaker(s) tripped. Reset or replace circuit breaker. Chapter 8
Lights do not work. p.55 ↗ Lamp not installed properly. Inspect lamp installation. Chapter 8
Lights do not work. p.55 ↗ Lamp wiring disconnected. Inspect lamp wiring. Chapter 8
Lights do not work. p.55 ↗ Defective lamp. Replace lamp. Chapter 8
Lights do not work. p.55 ↗ Light switch is defective. Replace light switch. Chapter 8
Lights do not work. p.55 ↗ Defective electronic ballast. Replace ballast. Chapter 8
Airflow monitor malfunction. No power. No lights. No display. p.55 ↗ Power cable to circuit board is disconnected and needs to be connected. Sensor cable needs to be connected. Power supply is not plugged into proper voltage; plug in power supply. Verify that all airflow monitor interface cables are connected. Check fuses on enclosure. Connect power cable to circuit board; connect sensor cable; plug power supply into proper voltage; verify all airflow monitor interface cables are connected; check fuses on enclosure. Chapter 8
No audible alarm. p.55 ↗ Alarm has been temporarily silenced using "SILENCE ALARM" or "enter" buttons. Check alarm status; refer to Chapter 6 or Digital 1000 Monitor Manual. Chapter 8
Wrong alarm set point. p.55 ↗ Airflow monitor was not properly adjusted. Repeat calibration steps outlined in this manual in Chapter 6 or in the supplied Digital 1000 Monitor Manual. Chapter 8
Constant audible alarm. p.55 ↗ Airflow monitor calibration or airflow issue. Check airflow and calibration of airflow monitor. See Chapter 6. Chapter 8
Continuous alarm. p.55 ↗ Face velocity of the enclosure may have changed; airflow of the system may have changed; ULPA filter may have become loaded. Check the face velocity of the enclosure. If incorrect, adjust the speed control to increase face velocity. If face velocity is correct, calibrate the airflow monitor outlined in this manual in Chapter 6. Chapter 8
Monitor alarms; air way to airflow monitor sensor is blocked by insects, dust or debris. p.55 ↗ Airway to airflow monitor sensor is blocked by insects, dust or debris. Lightly clean the airway with clean air. Be careful not to touch sensitive electrical components. Chapter 8
Audible disable will not stay operational. p.55 ↗ An alarm condition must be continuously present before the audible alarm can be silenced. If flow conditions fluctuate near the alarm set point, the airflow monitor will automatically reset it. Action should be taken to bring the enclosure airflow into proper operating parameters or adjust the alarm set point lower. Chapter 8