Agilent Technologies 280FS AA
Agilent Technologies 280FS AA — Atomic spectroscopy.
The Agilent 280FS AA is a Fast Sequential flame atomic absorption spectrometer with transverse Zeeman background correction and an 8-position lamp turret. It measures up to 10 elements per sample in about 2 minutes, with 1% RSD precision and 10 mL sample consumption. It is used for multi-element trace metal analysis in flame AA workflows.
Agilent Technologies Flame Atomic Absorption Instruments Series — Model Comparison & Selection
Full specifications
| Analysis Time (8 Elements) | 95 minutes |
| Dilution Error | -1 % |
| Precision | 1 %RSD |
| Sample Consumption | 10 mL |
| Sensitivity Increase | 40 % |
| Lamps mfr | four four |
| Background correction mfr | Transverse Zeeman Zeeman |
| Dilution factor mfr | 1 |
| Number of determinations mfr | 53 |
| Reproducibility mfr | 1 |
| Elements measured per sample mfr | 10 elements |
| Analysis time per sample mfr | 2 minutes |
| Lamp positions mfr | 8 positions |
| Default operating mode mfr | Fast Sequential Sequential |
| Lamp count mfr | 4 lamps |
| lamp capacity (240 FS) mfr | four lamps lamps |
| lamp capacity (240Z) mfr | four lamps lamps |
| lamp capacity (280FS) mfr | eight lamps lamps |
| lamp capacity (280Z) mfr | eight lamps lamps |
| elements per sample in Fast Sequential mode mfr | 10 minutes |
| gas and time reduction (PROMT + FS) mfr | 60 |
| background correction accuracy improvement mfr | 11 improvement |
| PSD120 autosampler capacity mfr | 130 solutions |
| UltrAA lamp lifetime mfr | 8000 hours |
| SIPS over-range dilution factor mfr | 200 x |
| Standard concentration mfr | 5 mg/L |
Description
Construction and series positioning
- The 280FS AA is a flame AA spectrometer built around a Fast Sequential (FS) optical and sample-handling architecture; it is the higher-tier FS model alongside the 240FS AA, while the 55B AA is a single-element flame AA with 0.9 Abs sensitivity.
- It carries an 8-position lamp turret (four lamps installed in the verified configuration) and transverse Zeeman background correction, distinguishing it from the 240FS AA and from graphite-furnace siblings (240Z/280Z AA) that use Zeeman GFAA rather than flame FS operation.
- Default operating mode is Fast Sequential, which sequences element measurements without operator intervention between lamps.
Behavior under load and in different modes
- In FS mode the instrument measures 10 elements per sample in about 2 minutes; an 8-element analysis is quoted at 95 minutes, reflecting the sequential nature of the measurement rather than simultaneous detection.
- Precision is 1 %RSD, dilution error is -1 %, and sample consumption is 10 mL per measurement cycle; a 40 % sensitivity increase is specified relative to the reference configuration.
- Standard concentration for the verified calibration point is 5 mg/L with a dilution factor of 1 and 53 determinations, indicating the calibration/validation basis rather than an operating range.
Installation, connection and control
- The 280FS AA is part of the Agilent AA range controlled by a single computer; Duo configurations pair one flame AA and one graphite furnace AA under one computer, but the 280FS AA itself is a flame-only FS instrument.
- SIPS 10 (single pump) and SIPS 20 (dual pump) sample introduction pump systems are separate accessories for SpectrAA FAAS instruments and are not part of the base spectrometer delivery.
- VGA 77 vapor generation is listed as an accessory in the range documentation, not as built-in hardware.
Integration & Operating Notes
Because the 280FS AA measures elements sequentially rather than simultaneously, the order and number of elements in a method determine cycle time; the verified 10-element, ~2-minute cycle and 95-minute 8-element run are consequences of that sequencing, so method design must account for lamp turret position and element order.
The Agilent AA range documentation states that flame and furnace instruments, including Duo combinations, are controlled by one computer; the 280FS AA therefore integrates into a single-PC control architecture, and accessory systems such as SIPS are managed through the same host rather than standalone controllers.
SIPS 10 and SIPS 20 are sample introduction pump systems supplied as accessories for SpectrAA FAAS instruments, not part of the 280FS AA base delivery; their peristaltic pump tubing is a consumable that must be scheduled and replaced independently of the spectrometer's own maintenance.
Selection & Integration Q&A
Pick the 280FS AA for multi-element flame work needing transverse Zeeman background correction and an 8-position lamp turret with Fast Sequential operation. The 240FS AA is the other FS flame model; the 55B AA is a single-element flame instrument (0.9 Abs sensitivity) without the FS multi-element workflow.
SIPS 10 (single pump) or SIPS 20 (dual pump) sample introduction pump systems and the VGA 77 vapor generation accessory are separate items for SpectrAA FAAS instruments; they are not part of the 280FS AA base delivery and must be ordered and integrated separately.
The 280FS AA runs under a single controlling computer. In Fast Sequential mode, 10 elements take about 2 minutes per sample, while an 8-element run is quoted at 95 minutes; plan method sequences and lamp turret positions around this sequential timing rather than assuming simultaneous detection.
SIPS pump tubing and VGA 77 vapor generation components are accessory consumables serviced separately from the spectrometer. The base 280FS AA delivery does not include SIPS 10/20 pumps or VGA 77; schedule their tubing replacement independently of the instrument's own lamp and burner maintenance.