No photo available yet

Agilent Technologies ·Made in USA · In Active Production

Agilent Technologies Feedthroughs for High & Ultra-high vacuum

Agilent Technologies Feedthroughs for High & Ultra-high vacuum — Vacuum technologies.

Agilent feedthroughs for high and ultra-high vacuum are component-level interfaces that pass electrical, motion, or fluid services through a vacuum chamber wall while preserving the pressure boundary. The supplied reference material is a general vacuum formulas and tables booklet, not a model-specific datasheet, so no flange size, leak rate, voltage, or current rating can be stated for this item. Selection must therefore be driven by the chamber flange standard, the service to be passed, and the required base pressure of the system.

Full specifications

Core Performance & Functional Specifications
Electron Charge 1.602 coulomb
Molar Volume 22.41 liters
Acceleration due to gravity mfr 9.8066
Angstrom unit mfr 10 m
Avogadro's number mfr 6.02214076
Boltzmann's constant mfr 1.38064852
Equivalent of heat mfr 4.185
Natural log base mfr 2.7183
Velocity of light mfr 2.9979
Velocity of sound mfr 343
Magnetic flux density mfr 1
Pressure conversion mfr 1 Torr
Pumping speed conversion mfr 1 L/s
Throughput conversion mfr 1 cc/sec
Outgassing rate mfr 2
Dimensions, Weight & Mechanical Design
Atomic Mass Unit 1.6605 grams
Standards, Safety & General Data
Standard pressure mfr 101325 Pa

Description

Construction and positioning

Behaviour under vacuum

Installation and operation

Integration & Operating Notes

Mounting
Flange standard and size must be confirmed before order

The verified record contains no flange designation for this feedthrough, so the mating chamber port cannot be checked from the card. Confirm the flange family and nominal size against the chamber drawing and the feedthrough's own datasheet before mounting; an unmatched flange cannot be sealed and will prevent the system from reaching base pressure.

Factory Specification Sheet (no model-specific flange data returned
Electrical
Electrical ratings are not available in the verified facts

No voltage, current, or conductor count is recorded for this feedthrough. Do not size cabling, feedthrough wiring, or power-supply insulation from this card; use the conductor rating from the feedthrough's own datasheet and keep the external wiring rated for the highest voltage present on the pins.

Factory Specification Sheet (no electrical data returned
Maintenance
Leak-check the feedthrough after every re-mounting

The reference booklet describes leak-detection practice but gives no service interval for this component. After any installation or re-sealing, perform a helium leak check on the feedthrough joint before running the process, since a disturbed elastomer or metal seal is the most common source of a new virtual leak.

Agilent Vacuum Leak Detection Reference Formulas, Properties and Glossary, 5994-5366EN

Selection & Integration Q&A

When should this feedthrough be chosen instead of another variant in the Agilent vacuum components range?

The verified facts list no sibling models, so no variant comparison can be made. Choose by the service to be passed (electrical, motion, or fluid), the chamber flange standard, and the required base pressure; confirm these three against the feedthrough datasheet before ordering.

What must be checked on the chamber side before this feedthrough is integrated?

The mating flange family and nominal size, the available port orientation, and the chamber's base-pressure target. The verified record gives no flange or leak-rate value, so these must be read from the feedthrough datasheet and matched to the chamber drawing before installation.

Are there mounting or duty-cycle limits documented for this feedthrough?

No mounting torque, temperature limit, or bakeout cycle is present in the verified facts; the attached document is a general formulas and tables booklet with no installation section. Obtain the feedthrough instruction sheet for torque and thermal limits before bakeout or repeated cycling.

What is supplied with the feedthrough and what must be ordered separately?

The verified facts contain no delivery scope, cable, connector, or accessory list. Cables, mating connectors, and flange hardware must be confirmed against the feedthrough's ordering information; none of these can be assumed to be included from this record.

Dimensional Drawings & Technical Documentation

Technical documentation