Agilent Technologies IDP 15 Dry Scroll Pump
Agilent Technologies IDP 15 Dry Scroll Pump — Liquid chromatography with Motor power 0.559 kW, Noise level 50 dB, Ultimate pressure 1.33 mbar.
The IDP-15 is a single-hermetic dry scroll pump with a 0.75 HP (550 W) motor, delivering 257 L/m at 60 Hz (213 L/m at 50 Hz) and an ultimate pressure of 1 × 10⁻² Torr. It is distinguished within the series by its 300 Torr maximum continuous inlet pressure and 20.7 g/hr water-vapor handling at gas ballast position 1. It serves as a roughing/backing pump for turbo or diffusion stages and for oil-free vacuum processes.
Full specifications
| Motor power | 0.75 HP |
| Noise level | 50 dBA |
| Ultimate pressure | 1 Torr |
| Coverslip type | No corrosive, explosive or particulate forming gases |
| Inlet Pressure | 1.0 atmosphere |
| Operating Speed | 1725 RPM |
| Water Vapor Handling Per Pneurop 6602 | 20.7 g/hr |
| Peak pumping speed mfr | 60 hr |
| Maximum outlet pressure mfr | 6.5 psig |
| Maximum recommended continuous inlet pressure mfr | 300 Torr |
| Exhaust connection mfr | 16 |
| Gas ballast mfr | 1 NPTF |
| Motor thermal protection mfr | Automatic thermal protection protection |
| Leak rate (with exhaust and gas ballast sealed) mfr | 1 helium |
| Vibration level at inlet, per mfr | 9 rms |
| Installation Category mfr | II II |
| Pollution mfr | 2 |
| Installation mfr | Category II II |
| Europe mfr | 10 m |
| Denmark mfr | 10 m |
| Switzerland mfr | 10 m |
| UK/Ireland mfr | 13 m |
| India mfr | 10 m |
| Israel mfr | 10 m |
| Japan mfr | 12 m |
| North America mfr | 15 m |
| NORTH AMERICA mfr | 1 agilent.com |
| PACIFIC RIM mfr | please visit our website for individual office i |
| Danemark mfr | 10 m |
| Suisse mfr | 10 m |
| Royaume-Uni/Irlande mfr | 13 m |
| Inde mfr | 10 m |
| Israël mfr | 10 m |
| Japon mfr | 12 m |
| Amérique du Nord mfr | 15 m |
| Will not start mfr | Motor thermal protector open open |
| Poor ultimate pressure mfr | System leak leak |
| Pump runs intermittently mfr | Motor thermal protector is cycling open and clos |
| X3815-67000 mfr | Replacement Tip Seal Set Set |
| X3815-69000 mfr | -15 Standard |
| X3815-69010 mfr | -15 Valve |
| Peak pumping speed at 60 Hz mfr | 257 L/m |
| Peak pumping speed at 50 Hz mfr | 213 L/m |
| Water vapor handling, position 2 mfr | 235 g/hr |
| Vibration level at inlet mfr | 9 rms |
| Shipping Weight | 54 kg |
| Weight | 30 kg |
| Weight, pump only mfr | 30 kg |
| Maximum Starting Current | 22.6 A |
| Typical Full Load Run Current | 8.05 A |
| Fuse type mfr | 215 D |
| Maximum starting current duration mfr | 1 sec. |
| Operating voltage, low range mfr | 100 VAC |
| Operating voltage, high range mfr | 200 VAC |
| Inlet flange | 25 |
| Interface dimensions mfr | 1 |
| Cooling System | Air-cooled |
| Storage temperature | -20...60 °C |
| Pollution Degree mfr | 2 |
| Altitude mfr | 2000 m |
| Hammering noise mfr | Pump overheated overheated |
| Vibration level at inlet, per ISO 10816-1 mfr | 9 rms |
| Noise level, per ISO 11201 mfr | 50 dBA |
Description
Construction and series positioning
- Single-hermetic dry scroll design with no lubricating oil in the vacuum path; leak rate <1 × 10⁻⁶ sccs helium with exhaust and gas ballast sealed.
- Factory-installed Integrated Isolation Valve (VPI) is an option; EC-stamped pumps engage the valve on both power loss and motor thermal shutdown, pre-EC pumps only on power loss.
- Service variants: X3815-69000 (Exchange IDP-15 Standard) and X3815-69010 (Exchange IDP-15 with VPI Valve).
- No sibling models are listed for this series; the IDP-15 is the sole configuration described.
Behavior under load and media
- Peak pumping speed is 257 L/m (15.4 m³/hr) at 60 Hz and 213 L/m (12.8 m³/hr) at 50 Hz; size foreline connections for the 50 Hz value on 50 Hz mains.
- Ultimate pressure 1 × 10⁻² Torr (1.3 × 10⁻² mbar) makes it a backing/roughing pump, not a standalone high-vacuum source.
- Maximum recommended continuous inlet pressure is 300 Torr; continuous operation above this risks overload and overheating.
- Water-vapor handling is 20.7 g/hr at gas ballast position 1 and 235 g/hr at position 2; select the port according to vapor load.
- Not for corrosive, explosive or particulate-forming gases.
Installation, connection and control
- Motor: 0.75 HP (550 W), 1-phase 100–120 VAC or 200–240 VAC, 50/60 Hz, ±10%; set the mains voltage selector switch before power-up.
- For 100/120 V service, connect to a 15 A circuit; maximum starting current is 25 A at 120 V/50 Hz and 23.5 A at 100 V/60 Hz for <1 sec.
- Inlet: NW25 or larger clean vacuum hardware; exhaust: short lengths of 16 mm ID or larger tubing; gas ballast inlet 1/4 NPTF.
- Insert a bellows between pump and chamber for vibration isolation and strain relief.
- Auto-reset thermal motor protector shuts down on overload and restarts when cooled.
- Integrated Isolation Valve (if fitted) has a ~30 s delay before opening after startup and a typical burst pressure around 50 mTorr; verify burst pressure on the specific system.
- Ambient operating temperature 5–40 °C; storage −20–60 °C; install indoors, protected from rain, steam and excessive humidity, with unobstructed air intakes and a minimum 2" gap front and back.
- Shipping locks must be engaged for shipping, long-distance moving or long-term storage, and disengaged before operation.
Integration & Operating Notes
The pump accepts 1-phase 100–120 VAC or 200–240 VAC, 50/60 Hz, ±10%. The voltage selector switch must be set to the actual mains voltage; incorrect setting can damage the motor or control electronics and is not covered by the auto-reset thermal protector.
Starting current reaches 25 A at 120 V/50 Hz and 23.5 A at 100 V/60 Hz for less than 1 second. A 15 A circuit with motor-start-rated breaker prevents nuisance trips; smaller circuits may trip at start, especially below 100 V.
Continuous operation above 300 Torr inlet pressure overloads the scroll mechanism and motor, causing overheating and potential damage. Use the pump only within this rough-vacuum range and transition to a backing stage for higher-vacuum work.
Water-vapor handling is 20.7 g/hr at gas ballast position 1 and 235 g/hr at position 2. For high vapor loads, use position 2; for dry nitrogen purge, supply approximately 5 l/min via the 1/4 NPTF gas ballast inlet.
Shipping locks must be engaged for shipping, long-distance moving or long-term storage, and disengaged before operation. Operating with locks engaged can damage the pump. Also raise the L-brackets so the pump rests on its rubber feet and leave a minimum 2" gap front and back for airflow.
Insert a bellows between the pump and vacuum chamber to reduce transmission of pump vibration to sensitive vacuum systems and to provide strain relief. Vibration level at the inlet is specified per the manual; rigid connection may couple vibration into the process.
On pumps fitted with the factory-installed Integrated Isolation Valve, the valve opens approximately 30 seconds after startup and has a typical burst pressure around 50 mTorr. EC-stamped pumps engage the valve on both power loss and motor thermal shutdown; pre-EC pumps only on power loss. Verify burst pressure on the specific system through testing.
Newly installed tip seals may require several hours of run time to seat properly. Do not judge pump performance immediately after tip seal replacement; ultimate pressure and pumping speed may improve over the first hours of operation.
The specified fuse is Littelfuse Series 215, 10 A, 250 V, 20 L × 5.2 mm D. Using any other fuse may compromise protection and certification. Investigate the cause of fuse failure before replacement.
The IDP-15 has an auto-reset thermal motor protector that shuts down on overload and automatically restarts when cooled. Intermittent running may indicate an overload condition that must be identified and corrected; do not rely on the protector as a process control.
Selection & Integration Q&A
The IDP-15 is the only model described in the supplied facts; no sibling models are listed. Choose it when you need 257 L/m at 60 Hz, 1 × 10⁻² Torr ultimate, and 300 Torr maximum continuous inlet pressure. For higher water-vapor loads, use gas ballast position 2 (235 g/hr).
The motor is 0.75 HP (550 W), 1-phase 100–120 VAC or 200–240 VAC, 50/60 Hz, ±10%. For 100/120 V service, connect to a 15 A circuit; starting current is 25 A at 120 V/50 Hz and 23.5 A at 100 V/60 Hz for <1 sec. Use a motor-start-rated breaker to avoid nuisance trips.
Install indoors, protected from rain, steam and excessive humidity, with ambient 5–40 °C. Leave a minimum 2" gap front and back for airflow; pump surface above 65 °C is potentially damaging. Disengage shipping locks before operation. Use NW25 or larger inlet hardware and short 16 mm ID or larger exhaust tubing.
Tip seal replacement is required periodically; new seals need several hours of run time to seat. Service kits and advance exchange pumps (X3815-69000 standard, X3815-69010 with VPI valve) are available separately. The Integrated Isolation Valve is a factory-installed option, not included in the base pump. Fuse: Littelfuse Series 215, 10 A, 250 V.