Elmo Rietschle IDP
Elmo Rietschle ·Made in Germany · In Active Production

Elmo Rietschle IDP

Elmo Rietschle IDP — Screw Vacuum Pumps with Motor power 22 kW, Pumping speed 1030 m³/h, Ultimate pressure 5 mbar.

The IDP is a dry screw vacuum pump with a 22 kW motor (IDP1100) or 18.5 kW motor (IDP850), achieving an ultimate pressure of 0.005 mbar and pumping speeds of 1030 m³/h and 850 m³/h respectively. It is distinguished within the series by its motor power and rotational speed (3600 rpm for IDP1100, 3300 rpm for IDP850), while sharing the same ISO100 inlet and DN100 PN10/ISO80 outlet connections. This pump is intended for clean, dry vacuum applications in industrial processes where oil-free operation and high pumping speed are required.

Motor power
22 kW
Pumping speed
1030 m³/h
Ultimate pressure
5 mbar

Full specifications

Core Performance & Functional Specifications
Motor power 18.5 kW (IDP850)
IDP1100: 22 kW
Pumping speed 850 m³/h (IDP850)
IDP1100: 1030 m³/h
Ultimate pressure 0.005 mbar (IDP850)
IDP1100: 0.005 mbar
Rotational speed 3300 rpm (IDP850)
IDP1100: 3600 rpm
Dimensions, Weight & Mechanical Design
Height 787 mm (IDP850 / IDP1100)
Length 1907 mm (IDP850 / IDP1100)
Weight 1055 kg (IDP850 / IDP1100)
Width 868 mm (IDP850 / IDP1100)
Interfaces, Connections & Control
Inlet flange ISO100 (IDP850 / IDP1100)
Outlet flange DN100 PN10 / ISO80 (IDP850 / IDP1100)
Operating Conditions, Environment & Protection
Noise level 60 dB (IDP850)
IDP1100: 61 dB
Operating temperature 5~46 °C (IDP850 / IDP1100)

Description

Construction and Positioning

Performance Characteristics

Installation and Operation

Integration & Operating Notes

Mounting
Ensure floor can support 1055 kg plus dynamic loads

The pump weighs 1055 kg and generates vibration during operation. Mount on a rigid, level surface capable of withstanding the static weight and dynamic forces. Use appropriate anchor bolts and vibration isolators if necessary to prevent transmission to the building structure.

Factory Specification Sheet
Electrical
Motor rated power is 22 kW (IDP1100) or 18.5 kW (IDP850)

The motor is rated at 22 kW for IDP1100 and 18.5 kW for IDP850. Ensure the power supply can deliver the required current and voltage (typically 400 V, 50 Hz or 460 V, 60 Hz). Use proper overload protection and wiring sized for the full load current. Consult the motor nameplate for exact electrical data.

Factory Specification Sheet
Process Limits
Ultimate pressure is 0.005 mbar; continuous operation at higher pressures may require derating

The pump achieves an ultimate pressure of 0.005 mbar. It is designed for continuous operation at inlet pressures down to this ultimate pressure. Operating at higher pressures may cause overheating or increased wear. Ensure the process gas is clean and dry, as the pump is oil-free and not suitable for condensable or particulate-laden gases without proper filtration.

IDS & IDP Series Dry Screw Vacuum Pump Manual
Environment
Ambient temperature must stay within 5–46 °C

The pump is rated for ambient temperatures between 5 °C and 46 °C. Outside this range, performance and reliability may be affected. Ensure adequate ventilation in the installation area to prevent overheating, especially if the pump is enclosed.

Factory Specification Sheet
Maintenance
Regular inspection of screws and bearings is required

Although the pump is dry-running, periodic inspection of the screw rotors and bearings is recommended to detect wear or debris. Follow the maintenance schedule in the manual. The pump does not require oil changes, but the bearings may be greased for life or require periodic relubrication depending on the design.

IDS & IDP Series Dry Screw Vacuum Pump Manual

Selection & Integration Q&A

When should I choose the IDP1100 over the IDP850 or an IDS variant?

Choose IDP1100 for higher pumping speed (1030 m³/h vs 850 m³/h) and 22 kW motor. IDP850 suits lower flow needs. IDS variants offer variable frequency, water cooling, or PLC controller for more flexible process control.

What are the requirements for connecting the IDP to my vacuum system?

Inlet is ISO100, outlet is DN100 PN10 / ISO80. Use compatible flanges and gaskets. Ensure piping supports are independent to avoid stress on pump. For outlet, consider a silencer or filter if exhaust is in a sensitive area.

Can the IDP operate continuously at ultimate pressure?

Yes, the pump is designed for continuous operation at ultimate pressure of 0.005 mbar. However, ensure process gas is clean and dry. For processes with high dust or condensables, install appropriate filters or traps upstream.

What maintenance items are not included in the base delivery?

Base delivery includes pump only. Required accessories: inlet filter, exhaust silencer, vibration isolators, and motor starter. Spare parts like screw rotors and bearings are available separately. Regular maintenance kits may be recommended.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
IDS & IDP Series Dry Screw Vacuum Pump
Datasheet ·3,0 МБ ·10 pp.
View PDF