Eppendorf DASGIP ® Bioblock/SciVario ® twin Spinner Vessels
Eppendorf DASGIP ® Bioblock/SciVario ® twin Spinner Vessels — Bioreactors & fermenters.
The DASGIP® Bioblock/SciVario® twin Spinner Vessels are autoclavable glass vessels with a stainless steel head plate, documented in a 0.7 L size (order no. 76DS0700ODSS) within a line covering 0.7, 1 and 1.5 L vessels and 250 mL–1.5 L working volume. They serve as the culture vessel in DASGIP parallel bioreactor systems for cell culture and fermentation runs.
Full specifications
Description
Construction and series positioning
- Autoclavable glass vessel body with stainless steel head plate; the documented 0.7 L unit (order no. 76DS0700ODSS) is one size in a line that also includes 1 L and 1.5 L vessels.
- The line spans a working volume of 250 mL to 1.5 L; the 0.7 L vessel is the smaller end of the DASGIP vessel range, below the 1 L and 1.5 L sizes.
- These vessels belong to the DASGIP Parallel Bioreactor Systems (4-, 8-, 16- and 24-fold, with or without Bioblock, standard CC and single-use CCSU variants); the glass vessel is the reusable counterpart to the single-use bioreactor option.
Behavior and media
- No digitized curve points, matched performance specs or extra factory specs were supplied for this model, so no mixing, mass-transfer or temperature behavior is stated here.
- The vessel is defined by its glass/stainless-steel materials and autoclavability; working volume is the only quantified process range available (250 mL–1.5 L across the line).
Installation and operation
- The attached document digests contain no extracted sections or actionable engineering facts on connections, control or operation; installation and control details must be taken from the full technical data sheet and the DASGIP/SciVario system manual rather than inferred here.
Integration & Operating Notes
The vessel line covers 0.7 L, 1 L and 1.5 L sizes with a working volume of 250 mL to 1.5 L; the 0.7 L unit (76DS0700ODSS) is the smallest documented size. Choose the size so the intended fill sits inside the working-volume band rather than at the nominal vessel volume.
The vessel is specified as autoclavable glass with a stainless steel head plate, so cleaning and sterilization are performed by autoclaving between runs. Plan autoclave cycles and spare head-plate seals into the run schedule; no further service intervals are given in the supplied digests.
The vessel is documented as part of the DASGIP Parallel Bioreactor Systems (4-, 8-, 16- and 24-fold, with or without Bioblock, CC and CCSU variants). Control hardware, sensor connections and drive details are system-level and are not contained in the supplied document digests.
Selection & Integration Q&A
Pick the 0.7 L vessel (76DS0700ODSS) when the working volume fits the lower part of the 250 mL–1.5 L band; move to the 1 L or 1.5 L vessel when higher working volumes are needed. All are autoclavable glass with stainless steel head plates.
The vessel is used within DASGIP Parallel Bioreactor Systems (4- to 24-fold, with or without Bioblock, CC or CCSU). The supplied digests do not list sensors, head-plate fittings, cables or drive components as part of the vessel delivery; confirm these against the system order.
No mounting, environment or duty-cycle limits are stated in the supplied document digests. The only confirmed handling requirement is that the glass vessel with stainless steel head plate is autoclavable; obtain installation limits from the full technical data sheet.
Between runs the vessel is cleaned and autoclaved as a glass/stainless-steel assembly. The digests give no service intervals and do not specify seals, sensors or cables as included; treat these as items to verify with the system documentation.