Induztr
Engineering Digest Document Viewer Related Models

400-DS Dissolution Apparatus Operator's Manual

Contents

  1. Overview pp. 5-8
    Overview of the manual and product description
  2. Spec pp. 9-14
    Power, bench space, and environmental specifications
  3. Procedure pp. 15-20
    General operating information and safety conventions
  4. Procedure pp. 21-26
    Cable and tubing connections, power on, logon
  5. Procedure pp. 27-29
    Adding users and system configuration
  6. Procedure pp. 30-40
    Creating, editing, copying, deleting configurations
  7. Procedure pp. 41-46
    Calibration procedures including volume calibration
  8. Procedure pp. 47-51
    Verifying tray, media, temperature, and reciprocation
  9. Procedure pp. 52-64
    Creating, editing, and managing methods
  10. Procedure pp. 65-69
    Channel selection valves and method execution
  11. pp. 70-72
    Reports, electronic signatures, and system cleaning
  12. Procedure pp. 73-77
    Cleaning, maintenance overview, and troubleshooting
  13. Services pp. 78-79
    Warranty, services, accessories, and consumables
  14. Warning pp. 80-88
    General safety, symbols, WEEE, and radio interference
  15. p. 89
    Index of the manual
  16. p. 14 table, 12 rows
  17. p. 31 table, 5 rows
  18. p. 26 table, 10 rows
  19. p. 32 table, 8 rows
  20. p. 54 table, 12 rows
  21. p. 55 table, 8 rows
  22. p. 56 table, 15 rows
  23. p. 68 table, 11 rows

Table 2: Performance specifications of the 400-DS Apparatus 7 (G7975A)

TypeSpecificationComments
Sample reciprocation20 mm± 1.0 mm
Dip rate1-35 DPM5.0% of rate
Temperature controlAmbient + 5-55 °C (41-131 °F)± 0.2 °C or better
Media volume3-5 mL (5 mL cell) or 8-12 mL (10 mL cell)1% of volume
Sample timepointsSpecified as HHH:MM:SS± 2% of timepoint
Samples per testUp to 13
Media types per testUp to 5
Evaporation0.2% or better of volume in 24 hours
CommunicationInstrument controlled with Dissolution Workstation software vers. 1.7 onwards; FW 1.6
Maintenance and safety-related featuresFunction to prevent overheating
GLP featuresUser management and run log (with errors) with the software
HousingAll materials are recyclable

Table 4: System Editor Screen 1 Options

Screen SectionParameterDescription
Section ParameterDescription
System NameEnter a name for your system.
LaboratoryEnter a laboratory name.
Restrict Execution To Specified ServerClick to display the name of the workstation or enter the name of the workstation connected to the system. Click No Restriction to allow the system to be run from any workstation. NOTE: The system must be physically connected.
Change ManagementIf applicable, select the box under Change Management in order to restrict the system editing rights to the current user. NOTE: This option prevents system configuration modification by anyone other than the system owner or a user with VkModifyOthersSystems privilege.

Table 3: 400-DS Workstation Screen Options

OptionDescription
System ConfigurationUse this option to configure the system. See System Configuration on page 29.
DiagnosticsUse this option to check the diagnostics of a dissolution apparatus or accessory within the system. See Manual Control/Diagnostics on page 47.
Method EditorUse this option to create a method, change or delete method parameters, run a report of the method setup, view the method audit trail, and verify the integrity of the method. See Method Editor on page 52.
Run MethodUse this option to run a method. See Running a Method on page 66.
Test ReportsUse this option to run a report of the completed method. See Test Reports on page 70.
Security Change UserTo change the user, click Change User. The Logon screen displays. Enter the appropriate user identification and password and click Logon.
Lock ApplicationTo lock the 400-DS Workstation screen, click Lock Application. The 400-DS Workstation Locked screen displays. Click the lock or the link to unlock the screen. The Logon screen displays. Enter the appropriate user identification and password as applicable and click Logon.
Audit TrailClick Audit Trail. The Security Audit Trail screen displays. Click Show Report to display the report. Change the start date, end date, and/or user identification as desired and click Retrieve Records to change the parameters for the information displayed.
PermissionsUse this option to view permissions assigned to the current user and the descriptions of the corresponding privileges. Click Permissions. The User Group Membership screen displays.
StatusClick one of the pie-shaped graphics under status to view the status of the corresponding dissolution system.

Options in the left pane may be grayed out depending on user permissions.

System Configuration

Screen SectionParameterDescription
Vial SizeClick the drop-down arrow to indicate the appropriate vial size.
Syringe SizeClick the drop-down arrow to indicate the appropriate syringe size.
Restrict Execution To Specified ServerManufacturerEnter the manufacturer of the calibrated temperature probe.
Restrict Execution To Specified ServerModel NameEnter the model name of the calibrated temperature probe.
Restrict Execution To Specified ServerSerial NumberEnter the serial number of the calibrated temperature probe.
Set Point Temperatures (ºC)Enter the 3 set points for the cell temperatures. Enter the temperature for each cell at each set point as determined from the diagnostics screen (see Temperature Calibration on page 41).
Volume Calibration CoefficientOffsetThe current offset displays in this area.
Volume Calibration CoefficientSlopeThe current slope displays in this area.

Table 7: Parameters Tab Options

OptionDescription
Sample Information
Product NameEnter the name of the product.
NotesEnter any relevant notes regarding the sample.
User Defined Labels
Label 1
Label 2
Label 3The fields in this area have default values of LOT, BATCH, and GROUP. These fields are customizable; enter the information that best serves the needs of the method parameters.
Error Tolerance (±)
TemperatureEnter the desired tolerance. If the tube temperature goes over or under the set temperature (see Verifying the Cell Temperature on page 50) by the amount of this tolerance, an error is recorded as part of the results.
SpeedEnter the desired tolerance. If the RPM goes over or under the set speed (see Verifying Reciprocation on page 51) by the amount of this tolerance, an error is recorded as part of the results.
Profile IntervalEnter the timepoint in hh:mm format at which the temperature and speed settings are recorded.
Change ManagementIf applicable, select the box under Change Management in order to restrict the method editing rights to the current user or any user with VkModifyOthersMethod.

NOTE: Profile measurements are optional. Values are always recorded at sample timepoints independent of this setting.

Table 8: Automated App7 Sequence Options

OptionDescription
Sample RowUse the up and down arrows to indicate the sample tray row number for which the parameters are being set. After clicking Add to List, use the up and down arrows to indicate the next row. NOTE: The sample row will increment automatically from the previous timepoint.
MediaUse the drop-down arrows to indicate Media A, Media B, Media C, Media D, Media E, or Rinse media.
Sampled Volume (mL)Use the up and down arrows to indicate appropriate volume based on your vial size.
Dissolution Volume (mL)Use the up and down arrows to indicate appropriate volume based on the system cell size.
Cell TemperatureEnter the desired tube temperature in degrees Celsius for the first timepoint.
Hold Time (mm:ss)Enter the desired duration for the sample holder to remain stationary prior to dipping in mm:ss format.
Dip Speed (DPM)Use the up and down arrows to indicate the desired dips per minute (DPM) for each applicable row of the 400-DS.
Dip Interval (hhh:mm:ss)Enter the desired duration for dipping in hhh:mm:ss format.

NOTE: The sample row will increment automatically from the previous timepoint.

Table 9: Automated App7 Options

Screen SectionParameterDescription
Media DescriptionMedia A
Media B
Media C
Media D
Media E
Rinse MediaEnter descriptions as appropriate for the different medias.
Syringe PropertiesAspirate Flow Rate (mL/s)Use the up and down arrows to indicate the rate at which the media is pulled into the syringe.
Dispense Flow Rate (mL/s)Use the up and down arrows to indicate the rate at which the media is dispensed from the syringe.
Aspirate Dwell Time (s)Use the up and down arrows to indicate the duration of time the plunger holds at the top of the stroke before dispensing. NOTE: The time specified is for full syringe volume. For smaller syringe volumes, it is calculated proportionately.
Prime Volume (mL)Use the up and down arrows to indicate the volume to be pulled before taking a sample.
Syringe Clean CyclesUse the up and down arrows to indicate the number of times to rinse the syringe between samples.
Sample Cell Clean CyclesUse the up and down arrows to indicate the number of times to rinse the sample cell between samples.
Needles Clean CyclesUse the up and down arrows to indicate the number of times to rinse the needles between samples.
Auto Clean After Method CompletionAuto Clean CyclesSpecify the number of cleaning cycles to be performed automatically at the conclusion of each test. Each cycle will flush the specified solution through the entire system - including syringes, sample cells and needles - and then dispense to waste.
Auto Clean Media SourceIndicate the source of the solution to be pumped through the system during for the cleaning cycle. Options include Media A, B, C, D, E and Rinse Port.

Table 10: Method Start Options

Screen SectionParameterDescription
Sample InformationProduct NameEnter the product name.
NotesEnter any appropriate notation.
Label 1Enter the appropriate information based on the user-defined labels (see Creating a Method on page 53).
Label 2
Label 3
Active ChannelsEnter the number of active heating channels. NOTE: Heating channels are counted from left to right.
Injection ControlEnable InjectionsN/A
TemperatureDelayed Start
Vessel Temperature StartN/A
Bath Temperature StartN/A
Time Delayed StartUse this option to program a delayed start. Enter the desired date and time to start the method.

Engineering Facts

14 facts · every claim linked to a page
Selection

The instrument is intended for small-volume dissolution testing of medical devices such as drug-eluting stents, so it should be selected only for that application.

Confirms the intended application before purchase and prevents selecting it for unsuitable dosage forms.

Source
“The Agilent 400-DS Dissolution Apparatus (G7975A) is the first compendial small-volume dissolution apparatus for testing medical devices such as drug-eluting stents (DES).”
Performance

The system can test up to 13 samples simultaneously, or 12 samples plus a control or standard.

Determines throughput and whether the lab's sample batch size fits the instrument capacity.

Source
“Saves time by simultaneously testing up to 13 samples, or 12 samples and a control or standard, while providing users direct visibility of each dissolution cell.”
Installation

The instrument requires additional clearance of 10 cm on each side, about 20 cm at the rear, and at least 40 cm above the unit.

Bench planning must account for these clearances for air circulation and access to connections.

Source
“It needs an additional 10 cm (4 inches) of space on either side and approximately 20 cm (8 inches) in the rear for air circulation and easy access to liquid and electric connections. Ensure a minimum clearance of 40 cm (16 inches) above the unit.”
Installation

The instrument must be operated in a fume cupboard or a well-ventilated room on a stable, level, non-flammable bench.

Ventilation and bench suitability are site prerequisites for safe installation.

Source
“Operate the instrument in a fume cupboard or in a well ventilated room.”
Safety

The power connector must remain easily reachable and unpluggable for emergency disconnection.

Installation layout must preserve access to the power plug as the primary disconnect.

Source
“Make sure the power connector of the instrument can be easily reached and unplugged.”
Installation

Only the Agilent-supplied power cord may be used, and it must not be used for other equipment.

Prevents electric shock or equipment damage from an incorrect or misused power cord.

Source
“Use only the power cord supplied by Agilent with this instrument.”
Safety

The instrument must not be operated from a power outlet without a protective ground connection.

Grounding is mandatory to avoid electric shock or short circuit.

Source
“Do not operate the instrument from a power outlet that does not have a protective ground connection.”
Operation

The 400-DS may be used with up to 100% concentrations of methanol and ethanol; other organic solvents have not been tested or validated.

Media and solvent selection must be limited to validated solvents to avoid unsafe or unvalidated operation.

Source
“The 400-DS (G7975A) may be used with up to 100% concentrations of Methanol and Ethanol. Other organic solvents have not been tested/validated for use.”
Installation

For a single-system setup, the loop back switch to the right of the right serial port must be set to the left (ON).

Correct switch position is required for proper serial communication in a single-system configuration.

Source
“Ensure the loop back switch (located to the right of the right serial port) is switched to the left (ON).”
Installation

In a multiple-system setup, the final 400-DS in the chain must have its loop back switch set to the left (ON), while non-final units must be set to the right (OFF).

Daisy-chain termination depends on correct switch settings for each unit in the series.

Source
“If this is the final Agilent 400-DS in the series, ensure the loop back switch (located to the right of the right serial port) is switched to the left (ON).”
Operation

Clicking Fill more than once without purging will overflow the cells.

Prevents media overflow and potential spillage during manual media control.

Source
“Do not click Fill more than one time without purging in between. The media will overflow the cells.”
Operation

When fewer than 13 active channels are used, sample vials must be present in positions 1 and 13 of each sample tray row.

Proper sensing, alignment, and balance of the sample tray depend on vials in these positions.

Source
“Ensure sample vials are present in positions 1 and 13 of each sample tray row if less than 13 active channels are used.”
Maintenance

The waste container must have enough free volume and its filling level must be checked regularly.

Waste handling capacity and regular checks are needed to avoid spills during operation.

Source
“The residual free volume in the appropriate waste container must be large enough to collect the waste liquid.”
Compliance

The software is 21 CFR Part 11 compliant and a single PC can independently control up to four 400-DS systems.

Supports regulated-environment selection and central control of multiple units from one workstation.

Source
“21 CFR Part 11 compliant software and a single PC can independently control up to four 400-DS systems.”