Induztr
Engineering Digest Document Viewer Related Models

Unichiller P180w-H Recirculating Chiller Datasheet

Contents

  1. Overview p. 1
    Introduces the Unichiller P180w-H chiller and its main features
  2. Spec pp. 1-2
    Performance, temperature, cooling capacity and dimensional data per DIN 12876
  3. p. 2 table, 8 rows
  4. p. 1 table, 31 rows

Technical data according to DIN 12876

ParameterValue
Volume of expansion48 l
Overall dimensions WxDxH **940x1290x1130 mm
Power supply (3 Phase)460V 3~ 60Hz
Pressure equipment categoryI
Degree of ProtectionIP20
min. ambient temperature5 °C
max. ambient temperature40 °C
from Serial-No.:1.0/21

** Please respect space requirements. See operating conditions at www.huber-online.com

Unichiller P180w-H — Technical data according to DIN 12876

ParameterValue
Order-No.3041.0008.01
Operating temperature range-20...100 °C
temperature set point / display5,7" colour Touchscreen
Internal temperature sensorPt100
Sensor external connectionPt100
Temperature stability at -10°C0,5 K
Interface digitalEthernet, USB (Host u. Device), RS232
Safety classificationIII / FL
Heating power2 kW
Cooling power at ambient temperature +20°C at 100°C18 kW
Cooling power at ambient temperature +20°C at 20°C18 kW
Cooling power at ambient temperature +20°C at 0°C10 kW
Cooling power at ambient temperature +20°C at -10°C6 kW
Cooling power at ambient temperature +20°C at -20°C3,5 kW
Refrigeration machinewater-cooled, CFC- and HCFC-free
Refrigerant (ASHRAE, GHS)R-449A (A1, H280)
Global Warming Potential (GWP)1397
Refrigerant quantity1,49 kg
CO2 equivalent2,1 t
Circulation pumpE2
max. delivery140 l/min
max. delivery pressure5,3 bar
Delivery at 2,8 bar126 l/min
Delivery at 3,0 bar124 l/min
Delivery at 3,5 bar115 l/min
Delivery at 4,0 bar103 l/min
Delivery at 4,5 bar83 l/min
Delivery at 5,0 bar43 l/min
Pump connectionG1 1/4 male
Cooling water connectionG3/4 male
min. filling capacity18 l

Cooling power values are given at ambient temperature +20°C for the listed temperatures (100°C, 20°C, 0°C, -10°C, -20°C).

Engineering Facts

14 facts · every claim linked to a page
Installation

The chiller is water-cooled and requires cooling water inlet temperature between 5°C and 20°C, so the site must provide cooling water within this range.

Cooling water outside this range will reduce cooling capacity or require additional measures, affecting utility design.

Source
“This temperature control unit is designed to operate with cooling water intake temperature between 5°C and 20°C.”
Installation

If cooling water temperature falls below the condensation point, the cooling water pipes in the unit must be insulated.

Prevents condensation and corrosion/electrical risk in the cooling water circuit.

Source
“When cooling water temperatures fall below the condensation point, it is essential to insulate the cooling water pipes in the unit.”
Performance

Higher cooling water temperature reduces cooling power and may require increased cooling water flow rate.

Cooling capacity must be derated based on actual site cooling water temperature and flow availability.

Source
“As the cooling water temperature increases, drop in the cooling power should be expected, and also an increased cooling water flow rate possible.”
Installation

The cooling water circuit materials include copper, stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM, so only suitable cooling water may be used.

Water quality must be compatible with these materials to avoid corrosion and fouling.

Source
“Materiels used in the cooling water circuit include; copper, Stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM. Please use suitable cooling water.”
Compliance

Voltage tolerance is ±5% only with simultaneous frequency tolerance of ±2%, and certain combinations are not allowed.

Site power quality must meet these limits; otherwise the unit may not operate reliably or warranty may be affected.

Source
“Voltage + / - 5% with a simultaneous frequency tolerance of + / - 2%”
Compliance

External branch circuit protection according to UL 489 is required.

Electrical installation must include UL 489 branch protection; affects panel design and compliance.

Source
“External branch circuit protection according to UL 489 required.”
Installation

Three-phase devices with current consumption less than 63A are supplied with cable but without plug.

The installer must provide a suitable plug or hardwired connection; affects electrical installation planning.

Source
“Three-phase devices with current consumption less than 63A --> with cable, without plug”
Installation

Three-phase devices with current consumption greater than 63A are supplied without cable and without plug.

Requires field wiring and connection by the installer; affects electrical installation scope.

Source
“Three-phase devices with current consumption greater than 63A --> without cable, without plug”
Operation

The unit is rated for ambient temperature from 5°C to 40°C.

Installation location must stay within this ambient range for proper operation.

Source
“min. ambient temperature 5 °C max. ambient temperature 40 °C”
Safety

The unit has adjustable overtemperature protection according to DIN 12876.

Safety function must be configured and tested during commissioning.

Source
“With adjustable overtemperature protection according to DIN 12876.”
Selection

The chiller is intended for externally closed applications.

Application type must match; open systems are not supported.

Source
“For externally closed applications.”
Selection

The refrigerant is R-449A with GWP 1397 and CO2 equivalent 2.1 t.

Refrigerant type and charge affect environmental compliance and service requirements.

Source
“Refrigerant (ASHRAE, GHS) R-449A (A1, H280)”
Installation

The unit requires a 460V 3~ 60Hz power supply.

Site power must match this supply; otherwise a transformer or different configuration is needed.

Source
“Power supply (3 Phase) 460V 3~ 60Hz”
Compliance

The equipment is classified as Class A, Group 1 for electromagnetic disturbance to EN55011.

Class A equipment may require EMC measures in residential or light-industrial environments.

Source
“Classification (disturbance) to EN55011: Class A, Group 1”