Induztr
Engineering Digest Document Viewer Related Models

HiPace 800 P with TC 400 — instruction manual

Technical Reference Summary

Covered Models & Document Scope

Operating instructions (PT 0319 BEN/F, 1211) for the Pfeiffer Vacuum HiPace 800 P process-version turbopump, operated with the electronic drive unit TC 400 (standard, PB/Profibus, E74/SEMI E74, DN/DeviceNet panel variants) at 48 V DC ±5%. High vacuum flange variants: DN 200 ISO-K and ISO-F (aluminium) and DN 200 CF-F (stainless steel). Scope of delivery: pump with TC 400, mating plugs for 'remote' and 'E74', protective flange covers, operating instructions.

Section-by-Section Technical Breakdown

pp. 9-10
Product Description

The HiPace 800 P is a process turbopump forming a complete unit with the TC 400 drive. Rotor bearing is hybrid: permanent magnetic bearing on the high vacuum side, ceramic ball bearing on the fore-vacuum side. Cooling is water (standard) or air (optional). Certified to CAN/CSA-C22.2 No. 61010-1, TÜV ID 0000021320.

  • Model designation: HiPace (family) 800 (size/pumping speed class) P (Process)
  • HV flange options: DN 200 ISO-K / ISO-F (aluminium), DN 200 CF-F (stainless steel)
  • Hybrid bearing: maintenance-free permanent magnetic bearing (HV side), ceramic ball bearing (fore-vacuum side)
  • Supply voltage 48 V DC ±5%; only Pfeiffer power supplies (TPS/DCU) allowed
  • On excess temperature the TC 400 automatically reduces drive power
pp. 11
Range of Application (Ambient Conditions)

Installation is weather-protected indoor, protection category IP 54, protection class III, overvoltage category II, pollution degree 2. Ambient temperature limits depend on cooling method; the pump is intrinsically safe by redundant temperature monitoring and reduces then cuts drive power on overheating.

  • Ambient temperature: +5 °C to +35 °C (air cooling), +5 °C to +40 °C (water cooling)
  • Relative humidity: max 50% at 40 °C, up to max 80% at 31 °C
  • Atmospheric pressure 75-106 kPa; installation altitude max 2000 m
  • Permissible surrounding magnetic field ≤6 mT; shielding required above 6 mT
  • Higher ambient temperatures permissible with reduced fore-vacuum pressure or gas throughput
pp. 12-15
Installation and Mounting

Details set-up, HV flange mounting (ISO-K claw clamps, ISO-F screws/studs, CF M8 studs/hex screws), flange loading limits, and torque values. Sudden rotor blocking can generate torques up to 4200 Nm, so fastening must absorb these; mixed flange-type combinations are prohibited. Counter-flange flatness must be ≤0.05 mm.

  • Max axial load on HV flange: 1000 N (100 kg), one-sided load not permitted
  • ISO-K DN 200: 8 claw clamps, tighten crosswise 5 / 15 / 25 ±2 Nm
  • ISO-F DN 200: 12 hex screws or stud screws, tighten crosswise 10 / 20 / 38 ±3 Nm; screw-in depth 1.5 d (>270 N/mm² flange) or 2.5 d (170-270 N/mm²)
  • CF DN 200: 24 M8 screws/studs, circular tightening 22 ±2 Nm, re-check torque after seal flow
  • Counter flange evenness max 0.05 mm over whole surface; flange material strength min 170 N/mm²
  • Sudden rotor blocking torques up to 4200 Nm — use only Pfeiffer original mounting components, never mix flange types
  • With oil-sealed backing pumps, fore-vacuum flange must point vertically downward (±25°)
  • Splinter shield DN 200 reduces pumping speed: H2 7%, He 11%, N2 23%, Ar 26%; protection screen: 2/3/7/8%
  • Max rotor temperature 90 °C; radiated heat input must not exceed 4.2 W; chamber flange ≤120 °C with casing heating + water cooling
  • Vibration damper does not compensate rotor-blocking torques; max temperature at vibration damper 100 °C
pp. 16-22
Connections to the Turbopump

Covers power supply, remote plug, accessory connections (4 preconfigured M12 ports), backing pump, air cooling, venting valve, heating jacket, sealing gas and water cooling connections. TC 400 factory presets: A1 air cooling unit, A2 backing pump, B1 venting valve, B2 casing heating; Y-connectors allow two units per port.

  • Remote mating plug bridges Pin 2, 3, 4, 14 to Pin 1 (supply) enabling stand-alone operation — automatic start on power-up
  • Backing pump must achieve ≤5 hPa; connected via relay box, default accessory port A2
  • Air cooling permissible up to +35 °C ambient; default accessory port A1
  • Venting valve: max connection pressure 150 kPa absolute; default accessory port B1; intake G 1/8"
  • Sealing gas: mandatory above 50% of max gas throughput (rotor cooling); flow rate 17.5-20 sccm; max connection pressure 150 kPa absolute
  • Heating jacket only permissible with stainless steel (CF-F) HV flange; min heating duration 4 h; fixing screw torques M5: 6/7/7 Nm, M6: 11/12/12 Nm (cold/heat-up/after cooling)
  • Water cooling: hose OD 8 mm / ID 6 mm, fore-line overpressure max 600 kPa, pH 7-9, chloride max 100 mg/kg, water hardness max 10 °dH (178 ppm CaCO3), oxygen max 4 mg/kg
  • Water cooling required whenever casing heating is used or pump connected to heated chamber
pp. 23-25
Operation

Commissioning, operation modes (stand-alone, remote, RS-485/DCU/HPU, fieldbus), LED status indication, temperature monitoring and switching off/venting. Factory parameters of the TC 400 are listed; gases with molecular mass >80 require consultation with Pfeiffer Vacuum.

  • Factory settings: P:027 gas mode 0 (heavy gases); P:700 max run-up time 8 min; P:701 rotation speed switchpoint 80% nominal; P:707 rotation speed setting 65% nominal; P:708 power consumption 100%; P:720 venting rotation speed 50% nominal; P:721 venting time 3600 s
  • LED display: green = pumping station on/off, yellow = warning, red = malfunction; differentiated display only via DCU/HPU
  • Switching off requires venting to avoid backstreaming contamination from fore-vacuum side
  • Rapid venting: 20 s at pressure rise rate max 15 hPa/s, valve cross-section adapted to chamber size; then vent with any additional valve
  • Delayed venting: valve opens at 50% nominal rotation speed or on mains failure, for 3600 s (1 h); restoring mains power aborts venting
  • Never operate with open HV flange; wrong gas mode with heavy gases can destroy the pump
pp. 26-28
Maintenance / Replacement

User-serviceable items are the operating fluid reservoir and the electronic drive unit. Operating fluid reservoir and bearings must be changed at least every 4 years (bearing via Pfeiffer Service). External cleaning with lint-free cloth and little industrial alcohol; no cleaning fluids inside.

  • Change operating fluid reservoir at least every 4 years; change bearing at least every 4 years (Pfeiffer Service)
  • Reservoir replacement: 3 Allen screws on end cover, 9 Porex rods replaced with tweezers, felt side of reservoir toward splash nut
  • End cover tightening torque: 2.5 Nm with new O-ring
  • Do not add additional operating fluid — reservoir is pre-filled
  • Decontaminate parts contaminated by pumped media before maintenance; dispose of reservoir per regulations
  • Shorter intervals for extreme loads/impure processes to be clarified with Pfeiffer Service
pp. 29-31
Decommissioning, Malfunctions and Service

Shutdown for longer periods, restart and disposal procedures, malfunction rectification and service contact. (Content in provided extract limited to table of contents; detailed procedures on pages 29-31.)

  • Sections 8-10 cover shutdown, restart, disposal, rectifying malfunctions and service
pp. 32-34
Spare Parts and Accessories

Spare parts lists for HiPace 800 P and approved accessories with order numbers are given in sections 11 and 12; use of original parts only.

  • Only accessories/spare parts named in the manual may be used (otherwise improper use)
pp. 35-38
Technical Data and Dimensions

Technical data for the HiPace 800 P 48 V DC variant and dimension drawings, plus declaration of conformity. The rating plate example shows S(N2) 260 l/s, 60,000 1/min (1000 Hz), weight 6.7 kg (example plate values).

  • Data tables on pages 35-37 cover general data, HiPace 800 P 48 V DC variant and dimensions

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Supply voltage is 48 V DC ±5%, protection class III, only original Pfeiffer power supplies (TPS 400 / DCU 400) permitted p.10 ↗ Power architecture must use Pfeiffer OEM supplies; third-party supplies void compliance guarantees HiPace 800 P with TC 400
Ambient temperature limits: +5 to +35 °C with air cooling, +5 to +40 °C with water cooling; use water cooling if ambient >35 °C p.11 ↗ Cooling selection depends on installation environment; air cooling only for ≤35 °C HiPace 800 P with TC 400
Sudden rotor blocking can generate torques up to 4200 Nm capable of tearing the pump off p.12 ↗ HV flange fastening must be rated for this torque; only original Pfeiffer mounting components HiPace 800 P, all flange variants
ISO-K DN 200: 8 claw clamps tightened crosswise in three steps at 5, 15, 25 ±2 Nm p.14 ↗ Defines correct clamp installation procedure and torque sequence DN 200 ISO-K variant
ISO-F and stud-screw DN 200 connections: 12 screws, crosswise 10 / 20 / 38 ±3 Nm; screw-in depth 1.5 d for flange >270 N/mm², 2.5 d for 170-270 N/mm² p.14 ↗ Counter flange material strength dictates screw engagement depth DN 200 ISO-F variant
CF DN 200: 24 M8 screws tightened circularly at 22 ±2 Nm, re-check torque after seal flow p.15 ↗ Copper seal creep requires torque re-check to preserve sealing DN 200 CF-F variant
Counter flange evenness must not exceed 0.05 mm over the whole surface; flange material strength min 170 N/mm² p.12 ↗ Specify counter-flange machining tolerances and material in chamber design All HV flange variants
Max axial loading of the HV flange is 1000 N (100 kg), one-sided load not permitted p.13 ↗ Limit attached hardware mass on the inlet flange HiPace 800 P
Max rotor temperature 90 °C; radiated heat input must not exceed 4.2 W; chamber flange ≤120 °C with casing heating and water cooling p.12 ↗ Hot processes require heat screening; design radiation shields if needed HiPace 800 P
Splinter shield DN 200 reduces pumping speed by 7% (H2), 11% (He), 23% (N2), 26% (Ar); protection screen by 2/3/7/8% p.13 ↗ Include speed derating in sizing calculations when particle protection is fitted DN 200 variants
Backing pump must generate ≤5 hPa fore-vacuum pressure; default accessory port A2 via relay box p.18 ↗ Backing pump sizing/selection criterion for the pumping station HiPace 800 P with TC 400
Sealing gas mandatory above 50% of max gas throughput (rotor cooling); flow 17.5-20 sccm; max supply pressure 150 kPa absolute p.21 ↗ Process setup must include sealing gas supply for high-throughput/unclean processes HiPace 800 P
Cooling water: OD 8 mm / ID 6 mm hoses, fore-line overpressure max 600 kPa, pH 7-9, chloride ≤100 mg/kg, hardness ≤10 °dH (178 ppm CaCO3), oxygen ≤4 mg/kg p.22 ↗ Water quality spec for facility cooling loop; dirt trap recommended in fore-line Water-cooled HiPace 800 P
Factory TC 400 parameters: gas mode 0 (heavy gases), max run-up time 8 min, speed switchpoint 80% nominal, set speed 65% nominal, venting speed 50% nominal, venting time 3600 s p.23 ↗ Baseline configuration for commissioning and parameter comparison TC 400 drive
Delayed venting opens the venting valve for 3600 s at 50% nominal speed or on mains failure; restoring mains aborts venting p.25 ↗ Defines power-failure venting behavior for process chamber protection TC 400 with Pfeiffer venting valve
Rapid venting: max pressure rise rate 15 hPa/s for 20 s, valve cross-section adapted to chamber size p.25 ↗ Prevents particle backstreaming and pump/chamber damage during fast venting HiPace 800 P systems
Operating fluid reservoir and pump bearings must be changed at least every 4 years p.26 ↗ Preventive maintenance scheduling requirement; bearing change via Pfeiffer Service HiPace 800 P
End cover tightening torque 2.5 Nm with new O-ring; 9 Porex rods and pre-filled reservoir replaced during fluid change p.26 ↗ DIY reservoir replacement procedure; no additional fluid to be added HiPace 800 P
Circuit breaker with interruption rating ≥10,000 A required per SEMI-S2 (pump has no built-in power disconnection device) p.5 ↗ User must install compliant disconnection device in the supply circuit TC 400 installations
Fore-vacuum flange must point vertically downward (±25°) with oil-sealed backing pumps; storage temperature -25 to +55 °C; magnetic field ≤6 mT p.8 ↗ Mounting orientation, storage and site EM environment constraints HiPace 800 P