Induztr
Engineering Digest Document Viewer Related Models

MVP 020-3 AC — instruction manual mvp 020 3 ac

Technical Reference Summary

Covered Models & Document Scope

Pfeiffer Vacuum operating instructions for the AC-series diaphragm vacuum pump MVP 020-3 AC (dry-compressing, 4 pumping stages, 2 diaphragm heads). Covers the single model MVP 020-3 AC; optional accessory: flushing gas nozzle with filter (PK 050 304 -U). Spare part packages for diaphragms/valves, fan and flushing gas nozzle are referenced in tables 9-11.

Section-by-Section Technical Breakdown

pp. 16-17
Product Description

The MVP 020-3 AC is a dry-compressing diaphragm pump with 2 diaphragm heads and 4 pumping stages, driven directly by a single-phase extended-voltage-range motor. Cooling is by convection only (no motor fan). The motor has a thermal protection switch that trips above 95 °C and restarts automatically after cooling.

  • Drive motor: switchable 100-120 V or 200-230 V (±10%), 50/60 Hz, with thermal switch and mains cable with plug.
  • Vacuum connection is 1/8" thread; exhaust with silencer; locking screw optional flushing gas nozzle; voltage selector switch and fuse holder on housing.
  • Scope of delivery: pump with drive, silencer, operating instructions, blind plug for vacuum connection.
pp. 19-22
Installation

Setup requires a flat horizontal surface, adequate air circulation (no fan — convection cooled), minimum clearances per Fig. 3, and permanent access to the mains plug. Vacuum and exhaust lines should be as short as possible with nominal diameter matching the connection; exhaust routed downward without shut-off units. Mains connection via voltage selector switch with two ranges, set only while disconnected from mains.

  • Voltage selector positions: '115' = 90-126 V 50/60 Hz; '230' = 180-254 V 50/60 Hz.
  • Provide a suitable mains fuse; secure earthed conductor (PE) connection; perform earthed conductor check after connection work.
  • Pump starts only against max 1 bar differential pressure between inlet and outlet, otherwise the motor jams and is damaged.
  • Condensate separator recommended on vacuum and exhaust sides when vapors are present; exhaust line with no shut-off units, routed downward.
  • Touch protection required if surface is accessible and temperature exceeds 70 °C.
pp. 23-25
Operation

Before commissioning, verify rating-plate frequency, free exhaust passage (max 1100 hPa absolute) and correct distributor installation. Warm-up is at least 30 minutes with the vacuum connection closed; specified throughput/final pressure is reached only at operating temperature. For condensable vapors, the optional flushing gas nozzle (PK 050 304 -U) improves condensate discharge; switch off after 5-10 min run-on with open vacuum connection.

  • Max permissible exhaust pressure: 1100 hPa absolute.
  • Maximum inlet pressure at the flushing gas nozzle: 1200 hPa absolute.
  • Flushing gas nozzle kit PK 050 304 -U: 1/8" thread filter and nozzle adapter with Ø 0.2 mm nozzle; mounting tools: Allen key WAF 5, open-end wrench WAF 14.
  • Shut-off units must open before or simultaneously with pump start.
  • Use inert flushing gas if explosive mixtures are possible; above 500 hPa intake pressure use an extraction line at the nozzle.
pp. 26-32
Maintenance

Diaphragms and valves are wear parts with typical 15,000 operating hour service life; motor bearing 40,000 h. Inspection interval at least every 6 months (level 1); diaphragm/valve change at least every 2 years (level 2/3) and full overhaul at least every 4 years. Cover fuse replacement (5×20 mm / 2.5 AT microfuse), diaphragm and valve replacement with exact spacer disk re-use, and final pressure verification.

  • Device fuse: microfuse 5×20 mm / 2.5 AT in fuse holder on side housing cover; wait 2 min for capacitor discharge.
  • Diaphragm replacement requires diaphragm key WAF 46; diaphragm installed blue side up; original spacer disks must be reinstalled per location (changed dead volume impairs final vacuum or damages bearings).
  • Housing cover cylinder screws tightened diagonally to max 6.0 ±1 Nm with calibrated torque wrench (tightening factor ≤1.6); valves must be in correct inlet/outlet orientation.
  • Pump head work on one pump side at a time to avoid interchanging components; tools WAF 15, WAF 16, Allen key WAF 4.
  • Final pressure check: 3 l vacuum chamber + Pirani gauge, run ≥2 hours with open flushing gas nozzle (if fitted); test values: <3 hPa with gas ballast, <2.0 hPa without.
  • After diaphragm/valve replacement the specified final pressure is reached only after a run-in period of several hours.
  • Clean diaphragms and valves only with clean dry cloth — no alcohol or cleaning agents on them.
pp. 33-41
Decommissioning, Disposal, Malfunctions and Service / Spare Parts / Accessories

Chapters 8-13 cover decommissioning, disposal of the diaphragm pump per general disposal regulations, a malfunction/troubleshooting table (Tbl. 8), Pfeiffer Vacuum service solutions, spare parts packages (diaphragms/valves, fan, flushing gas nozzle — Tbl. 9-11) and accessories ordering (Tbl. 12). Decontamination is required before any return or disposal of pumps used with toxic media.

  • Troubleshooting table provided in chapter 10 (Tbl. 8).
  • Spare part packages: diaphragms and valves (Tbl. 9), fan (Tbl. 10), flushing gas nozzle (Tbl. 11).
  • Accessories ordered per chapter 13 with Tbl. 12; specify rating-plate data when ordering spare parts.
pp. 42-44
Technical Data and Dimensions

Chapter 14 provides general information, the technical data table for MVP 020-3 AC (Tbl. 15), pressure and gas throughput unit conversion tables (Tbl. 13-14), materials in contact with process media (Tbl. 16) and dimension drawings for PK T01 101 A and PK T01 103 A | PK T01 104 | PK T01 110 A.

  • Materials-contact table (Tbl. 16) lists all parts wetted by process media — required for media compatibility checks.
  • Dimension drawings for variants PK T01 101 A and PK T01 103 A | PK T01 104 | PK T01 110 A (Fig. 11-12).

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Pumping stages: 4 stages across 2 diaphragm heads; dry compressing positive displacement principle with automatically actuating valves. p.20 ↗ Designates the pump for oil-free/dry vacuum generation; no lubricant in the pumped gas path. MVP 020-3 AC
Motor voltage ranges selectable via switch: '115' = 90-126 V, '230' = 180-254 V, both 50/60 Hz, ±10%. p.21 ↗ Verify mains voltage on-site before every installation/relocation and set the selector only with the pump disconnected from mains; wrong setting destroys the motor. MVP 020-3 AC
Motor thermal protection switch interrupts motor current above 95 °C and the motor restarts automatically after cooling. p.12 ↗ Secure the pump against unintentional restart before any hands-on work; automatic restart is a hazard in the rotating parts range. MVP 020-3 AC
Pump can be started only against max 1 bar differential pressure between inlet and outlet; otherwise the motor jams and is damaged. p.23 ↗ Open shut-off valves before or simultaneously with pump start; never start against a closed/pressurized exhaust. MVP 020-3 AC
Maximum permissible exhaust/back pressure: 1100 hPa absolute. p.23 ↗ Size and check exhaust lines for free passage; do not install shut-off units in the exhaust line. MVP 020-3 AC
Maximum permissible inlet pressure at the optional flushing gas nozzle: 1200 hPa absolute. p.24 ↗ Limit inert flushing gas supply pressure accordingly when fitting nozzle kit PK 050 304 -U (Ø 0.2 mm nozzle, 1/8" thread). MVP 020-3 AC with flushing gas nozzle
Protection degree IP 40 (IEC 60529) / NEMA type 1 (UL 50E); ambient +10 to +40 °C, max 2000 m altitude, pollution degree 2, overvoltage category II. p.14 ↗ Pump is for indoor, dust/weather-protected, non-explosive dry locations only; above 1000 m altitude verify cooling per DIN EN 61010. MVP 020-3 AC
Surface temperature can exceed 70 °C in normal operation and exceed 105 °C in the event of a fault. p.11 ↗ Provide touch protection if accessible; allow cool-down before maintenance. MVP 020-3 AC
Typical service life: diaphragms 15,000 h, valves 15,000 h, motor bearing 40,000 h. p.26 ↗ Schedule diaphragm/valve replacement as wear-part maintenance and plan bearing overhaul at 40,000 h. MVP 020-3 AC
Maintenance intervals: inspection at least every 6 months, diaphragm/valve change at least every 2 years, full overhaul/replacement of all wear parts at least every 4 years. p.27 ↗ Minimum service plan; extreme processes may require shorter intervals agreed with Pfeiffer Vacuum Service. MVP 020-3 AC
Device fuse: microfuse 5×20 mm / 2.5 AT in fuse holder on the side housing cover. p.28 ↗ Stock the correct fuse type; disconnect mains and wait 2 minutes for capacitor discharge before replacement. MVP 020-3 AC
Housing cover cylinder screws: tighten diagonally to max 6.0 ±1 Nm with a calibrated torque wrench (tightening factor ≤1.6). p.31 ↗ Prevents head leakage/deformation during reassembly after diaphragm/valve change. MVP 020-3 AC pump heads
Diaphragm service requires diaphragm key WAF 46; diaphragm is fitted blue side up; original spacer disks must be reused in their original positions. p.28 ↗ Altered dead volume from wrong spacer disks impairs final vacuum or causes bearing damage; use overhaul kit incl. key. MVP 020-3 AC
Final pressure test values: <3 hPa with gas ballast, <2.0 hPa without gas ballast, measured on a ~3 l vacuum chamber with Pirani gauge after ≥2 h operation. p.31 ↗ Acceptance criterion after maintenance; note specified final pressure is only reached after several hours run-in following diaphragm/valve replacement. MVP 020-3 AC
Pump is convection-cooled only; the drive motor has no fan. p.16 ↗ Ensure adequate air circulation, especially in closed housings; observe minimum clearances to walls/adjacent components. MVP 020-3 AC
Vacuum connection thread is 1/8"; vacuum/exhaust lines should be as short as possible with nominal diameter equal to the connection. p.16 ↗ Minimizes throttling/pressure losses; use PVC or metallic hoses with flange connections from the Pfeiffer component shop. MVP 020-3 AC
Warm-up time is at least 30 minutes; specified throughput and final pressure are reached only at operating temperature. p.23 ↗ Run the pump ≥30 min with vacuum connection closed before process start. MVP 020-3 AC
Switch-off procedure: run the pump 5-10 minutes with open vacuum connection to purge condensate. p.25 ↗ Prevents condensate accumulation/corrosion in the pump interior when pumping condensable vapors. MVP 020-3 AC
For intake pressures >500 hPa, process gas may escape from the flushing gas nozzle. p.24 ↗ Use an extraction line at the nozzle in such operating regimes. MVP 020-3 AC with flushing gas nozzle
Improper use includes pumping corrosive, explosive, radioactive, fluid, particle/dust-laden, FPM-solubilizing media and vapors from combustible liquids; cleaning of diaphragms/valves with alcohol is prohibited. p.13 ↗ Check media compatibility (Tbl. 16) before selection; only clean diaphragms/valves with a clean dry cloth; use inlet filters/separators for contaminated gases. MVP 020-3 AC