Operating Instructions — VSI 300 OXY vacuum pump (BA 832-43-EN, EN)
Technical Reference Summary
Covered Models & Document Scope
Este documento (BA 832-43-EN, edición 1.4.2016) cubre la bomba de vacío de tornillo S-VSI 300 (43) OXY, una variante OXY con barniz azul para el manejo de gases con mayor proporción de oxígeno (>21 % en volumen) y otros oxidantes. Describe la versión estándar con refrigeración por flujo continuo y las opciones: unidad de control, válvula de agua termostática (control de refrigeración por agua dulce) y sistema de refrigeración por circulación. Las variantes de motor referenciadas son 5,5 kW y 7,5 kW.
Section-by-Section Technical Breakdown
Describe la disposición mecánica y el principio de funcionamiento de la bomba de vacío de tornillo de doble eje S-VSI 300 (43) OXY, incluyendo figuras de identificación de componentes y el contenido de la placa de características. La bomba utiliza dos rotores de tornillo paralelos sin contacto sincronizados por un par de engranajes lubricados con aceite; la caja de engranajes y la cámara de compresión están separadas por sellos especiales con una zona intermedia ventilada a la atmósfera. Una válvula de lastre de gas está instalada de serie.
- Double-shaft screw vacuum pump with dry, non-contacting rotors
- Gearbox and compression chamber separated by special seals; intermediate area can be loaded with sealing gas (special version)
- Gas ballast valve fitted as standard to reduce water vapour condensation
- OXY pumps varnished blue for differentiation from standard versions
- Driven by standard flanged three-phase motor via elastomer coupling
- Data plate shows type/size, serial number, year, item no., suction capacity, ultimate vacuum, speed, motor output, operating mode
Define el rango de presión de aspiración, la capacidad máxima de bombeo y las restricciones operativas especiales para la variante OXY. La bomba es adecuada para la evacuación de sistemas cerrados o vacío continuo entre 0,1 y 1000 mbar (abs.) y para gases muy húmedos. Se aplican límites específicos a la versión de motor de 5,5 kW y a la evacuación de sistemas cerrados.
- Intake pressure range 0.1 to 1000 mbar (abs.)
- Maximum pumping capacity with free suction 320 m3/h at 50 Hz
- 5.5 kW motor version only for continuous operation S1
- Closed-system evacuation volume max. 80 l
- Frequent switching (>10 times/hour) or high ambient/intake temperatures may exceed motor winding and bearing temperature limits
- Outdoor installation requires protection from environmental influences (e.g. protective roof)
Cubre la refrigeración estándar por flujo continuo a través de la carcasa del compresor de doble pared y la unidad de control opcional, la válvula de agua termostática y el sistema de refrigeración por circulación. Los dispositivos de seguridad incluyen válvula solenoide, control de temperatura y válvula de seguridad. Se especifican los ajustes de fábrica y las tensiones de control.
- Standard continuous flow cooling through cavity in double-walled compressor housing
- Temperature control factory setting Tmax = 60 °C
- Safety valve protects against cooling water pressure > 6 bar
- Solenoid valve control voltage 24 V DC
- Thermostatic water valve (option) factory setting Tmax = 55 °C
- Circulation cooling option uses thermostat-controlled three-way valves, temperature switch and flow switch; weight 101/131 kg, tank capacity 30 l, dimensions 580 x 580 x 650 mm
Proporciona los requisitos para la preparación del lugar de instalación, el montaje, la conexión de las tuberías de aspiración y descarga, la conexión del agua de refrigeración, el llenado del aceite lubricante y la conexión del motor. Incluye requisitos de espacio libre, límites de contrapresión, calidad del agua de refrigeración y datos de conexión eléctrica.
- Cooling air inlets/outlets must be at least 30 cm from adjacent walls
- Machine must be set up horizontally on a level, straight foundation able to take its weight
- Suction pipe must not be too narrow or too long; only screw pipes in by hand
- Exhaust air outlet must not be closed or restricted; prevent liquid accumulation in exhaust line
- Cooling water: pH-neutral, clean, filtered; operating pressure max. 6 bar; temperature 15–50 °C
- Anti-freeze at least 10 % to prevent frost damage
- Lubricating oil OXY-GEAR-LUBE 160 filled to middle of sight glasses
- Motor protection class IP 55, insulation class F; electrical installation per EN 60204
- Permissible without derating: ±5 % voltage deviation, ±2 % frequency deviation
Describe las comprobaciones de puesta en marcha, incluida la verificación del sentido de giro y el procedimiento posterior a la marcha, además de los pasos de puesta fuera de servicio, almacenamiento y puesta en marcha de nuevo. Enfatiza el uso exclusivo de OXY-GEAR-LUBE 160 y el peligro de explosión por la mezcla de sustancias orgánicas con oxígeno.
- Check rotation direction by brief start (max. 2 s); motor fan must rotate clockwise
- Use phase sequence indicator to check for anti-clockwise rotating field
- Post-run at 50–100 mbar (abs.) with dry air for minimum 10 minutes before non-operating periods >2 hours
- Decommissioning: switch off, close cut-off devices, disconnect power, depressurise, remove pipes, seal connections, drain cooling water and condensate
- Only OXY-GEAR-LUBE 160 may be used; other lubricants or greases prohibited (explosion danger)
- If oil is suspected of mixing with organic substances, change oil immediately and have pump cleaned by authorised Elmo Rietschle personnel
Define los intervalos de mantenimiento y los procedimientos para cambios de aceite, filtrado de aire, inspección del acoplamiento y mantenimiento del sistema de refrigeración. Especifica el lubricante requerido, los agentes de limpieza y las precauciones de seguridad, incluida la prohibición de aire comprimido aceitoso.
- Monthly: check pipes/screws for leaks, terminal box and cable inlets, clean cooling ribs, check oil level, check cooling water system
- Oil change every 7,500 operating hours with OXY-GEAR-LUBE 160
- Clean intake air mesh filter and gas ballast valve filter depending on contamination
- Coupling sprocket checked at least once a year; wear reduces with frequent starting and high ambient temperature
- Clean dirt trap in cooling circuit depending on cooling liquid quality
- Only washing agent Antikor 30-57 with wetting agent 200-4 (Kluthe) permitted for filter cleaning
- Do not use oily compressed air for cleaning (explosion danger)
Especifica cómo pedir piezas de repuesto utilizando la lista de piezas de repuesto E 832/6 para S-VSI 300 (43) OXY y señala que las piezas de desgaste y las juntas se enumeran por separado. Solo se pueden utilizar piezas originales o aprobadas por el fabricante.
- Spare parts list E 832/6 for S-VSI 300 (43) OXY
- Download from manufacturer website under Downloads > Product Documents > S-Series > Spare Parts
- Wear parts and gaskets indicated separately
- Only original spare parts or manufacturer-approved parts permitted
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| La temperatura ambiente y de aspiración debe estar entre 5 y 40 °C. p.7 ↗ | Operation outside this range requires consultation with the manufacturer; selection must account for site temperature. | S-VSI 300 (43) OXY |
| Contrapresión en el lado de salida: S-VSI (43) 7,5 kW < +0,2 bar; S-VSI (43) 5,5 kW < +30 mbar. p.7 ↗ | Discharge piping and silencer must be sized so that these limits are not exceeded. | S-VSI 300 (43) OXY motor variants |
| Rango de presión de aspiración para vacío continuo: 0,1 a 1000 mbar (abs.). p.15 ↗ | Pump is suitable for closed-system evacuation and continuous vacuum within this range. | VSI OXY |
| Capacidad máxima de bombeo con aspiración libre es 320 m3/h a 50 Hz. p.15 ↗ | Use data sheet D 832/43 for pumping capacity dependence on intake pressure. | S-VSI 300 (43) OXY |
| La versión de motor de 5,5 kW solo puede operarse en funcionamiento continuo S1. p.15 ↗ | Do not apply intermittent duty to the 5.5 kW variant. | S-VSI 300 (43) OXY with 5.5 kW motor |
| Al evacuar sistemas cerrados, el volumen a evacuar debe ser máx. 80 l. p.15 ↗ | Larger closed volumes require alternative evacuation strategy or consultation. | S-VSI 300 (43) OXY |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.18 ↗ | Installation layout must provide this clearance to avoid recirculation of cooling air. | S-VSI 300 (43) OXY |
| La presión de servicio del agua de refrigeración no debe superar los 6 bar; la temperatura del agua de refrigeración debe estar entre 15 y 50 °C. p.21 ↗ | Cooling water supply must be regulated and monitored within these limits. | S-VSI 300 (43) OXY |
| El agua de refrigeración debe ser neutra en pH, limpia y filtrada; anticongelante al menos 10 % para prevenir daños por heladas. p.21 ↗ | Water quality per info sheet I 832-EN; anti-freeze concentration adjusted to ambient conditions. | S-VSI 300 (43) OXY |
| El aceite lubricante especificado es OXY-GEAR-LUBE 160; no se pueden utilizar otros lubricantes o grasas. p.22 ↗ | Explosion hazard if non-compliant lubricant is used; oil must be filled to middle of sight glasses. | VSI OXY |
| Clase de protección del motor IP 55, clase de aislamiento F; instalación eléctrica según EN 60204. p.23 ↗ | Main switch must be provided by operating company; motor protection switch with delayed switch-off recommended. | S-VSI 300 (43) OXY |
| Sin reducción de potencia, desviación de tensión permitida ±5 % y desviación de frecuencia ±2 %. p.23 ↗ | Mains conditions at installation site must match motor data plate within these tolerances. | S-VSI 300 (43) OXY |
| Verificación del sentido de giro: arranque breve máx. 2 segundos; el ventilador del motor debe girar en sentido horario. p.26 ↗ | Incorrect rotation direction damages the machine; use phase sequence indicator. | S-VSI 300 (43) OXY |
| Marcha posterior a 50–100 mbar (abs.) con aire seco durante mínimo 10 minutos antes de períodos de inactividad >2 horas. p.26 ↗ | Removes dampness and impurities to prevent deposits and starting problems. | S-VSI 300 (43) OXY |
| Intervalo de cambio de aceite: cada 7.500 horas de funcionamiento con OXY-GEAR-LUBE 160. p.29 ↗ | Maintenance planning must include oil changes at this interval; check oil level monthly. | S-VSI 300 (43) OXY |
| La rueda dentada del acoplamiento debe verificarse al menos una vez al año; los arranques frecuentes y la alta temperatura ambiente reducen su vida útil. p.34 ↗ | Defective sprocket may lead to rotor shaft breakage. | S-VSI 300 (43) OXY |
| Ajuste de fábrica del control de temperatura Tmax = 60 °C; ajuste de fábrica de la válvula de agua termostática Tmax = 55 °C; tensión de control de la válvula solenoide 24 V DC. p.16 ↗ | Cooling control settings must be verified during commissioning. | S-VSI 300 (43) OXY with control unit / thermostatic water valve |
| Opción de refrigeración por circulación: peso 101/131 kg, capacidad del depósito 30 l, dimensiones 580 x 580 x 650 mm. p.17 ↗ | Space and floor loading must accommodate these dimensions and weight. | S-VSI 300 (43) OXY with circulation cooling option |
| Condiciones de almacenamiento: humedad relativa 0–80 %, temperatura de almacenamiento -10 a +60 °C, máx. 6 meses. p.11 ↗ | Long-term storage beyond 6 months requires consultation of storage guidelines I 150-EN. | S-VSI 300 (43) OXY |
| La instalación a más de 1000 m sobre el nivel del mar causa una reducción notable de la potencia. p.19 ↗ | Contact manufacturer for high-altitude applications. | S-VSI 300 (43) OXY |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.37 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.37 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.37 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.37 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 2 or IEC 947-4) | |
| Pumping capacity is insufficient p.37 ↗ | The mesh filter is dirty | Clean or replace the mesh filter | Section 7.2.2, Section 7.4 |
| Pumping capacity is insufficient p.37 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Pumping capacity is insufficient p.37 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.38 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.38 ↗ | Too little cooling water | Note cooling water consumption | Section 9 |
| Final pressure (max. vacuum) is not reached p.38 ↗ | The mesh filter is dirty | Clean or replace the mesh filter | Section 7.2.2, Section 7.4 |
| Machine gets too hot p.38 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.38 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.38 ↗ | Cooling air supply is obstructed | Clean the cooling ribs | Section 7.2 |
| Machine gets too hot p.38 ↗ | The cooling water system is obstructed | Check the cooling water system and the pipes | Section 7.2 |
| Machine gets too hot p.38 ↗ | Too little cooling water | Note cooling water consumption | Section 9 |
| Machine gets too hot p.38 ↗ | Cooling water inflow is too hot | Note the max. intake temperature | Section 9 |
| The machine makes a abnormal noise p.38 ↗ | Deposits on the rotors | Clean the working space and the rotors | Elmo Rietschle Service |