HiPace 400 P with TC 400 — product leaflet
Technical Reference Summary
Covered Models & Document Scope
Pfeiffer Vacuum HiPace 400 P turbomolecular vacuum pump — a single model datasheet (3 pages). Covers the standard pump plus listed accessories/options: electrical adapter, mains/connecting cables, fieldbus systems (Profibus, Profinet, Ethercat, Devicenet, SEMI E74), power supply kit and display unit, mounting kit, safety valve, venting accessories, power failure venting unit, vibration damper.
Section-by-Section Technical Breakdown
Positions the HiPace 400 P as a high-performance turbomolecular pump specially designed for coating processes with an optimized rotor/stator concept. Highlights hybrid bearing technology for long life and maximum uptime, and on-site bearing change capability with insensitivity to process dust.
- Designed for coating processes with optimized rotor/stator concept
- Best-in-class hybrid bearing technology, long life cycle, maximum uptime
- On-site bearing change possible; insensitive to process dust
- Accessories/options: electrical adapter, mains cable, connecting cable, fieldbus systems, power supply kit and display unit, mounting kit, safety valve, venting accessories, power failure venting unit, vibration damper
Pumping speeds, compression ratios and gas throughputs for N₂, H₂, He and Ar at final rotational speed, plus forevacuum limit, run-up time and communication interfaces. Core sizing data for pump selection.
- Pumping speed: N₂ 350 l/s, H₂ 225 l/s, He 420 l/s, Ar 320 l/s
- Compression ratio: N₂ 1·10⁶, H₂ 4·10², He 3·10³, Ar 1·10⁷
- Gas throughput at final rotational speed: N₂ 2 hPa·l/s, H₂ 4 hPa·l/s, He 4 hPa·l/s, Ar 1 hPa·l/s
- Max. forevacuum pressure for N₂: 0.9 hPa
- Run-up time: 1.6 min
- Standard interfaces: RS-485, remote; optional: Profibus, Profinet, Ethercat, Devicenet, SEMI E74
Mechanical envelope data: mounting orientation, noise level, weight, and inlet/outlet flange connections. Relevant for system layout and integration.
- Mounting orientation: arbitrary
- Sound pressure level (EN ISO 2151): 50 dBA
- Weight: approx. 10.9 kg
- Gas inlet: DN 100 ISO-K/ISO-F/CF-F; outlet: DN 25 ISO-KF / G 1/4"
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Applies To |
|---|---|---|
| Pumping speed is 350 l/s for N₂ and 420 l/s for He (He speed higher than N₂). p.2 ↗ | Size backing pumps and conductance calculations using gas-specific speeds; do not assume a single N₂-equivalent value for light gases. | HiPace 400 P |
| Compression ratio for H₂ is only 4·10², versus 1·10⁶ for N₂ and 1·10⁷ for Ar. p.2 ↗ | Ultimate pressure in hydrogen-bearing processes is strongly limited by foreline pressure; use a clean, low-pressure backing pump for low H₂ partial pressure. | HiPace 400 P |
| Maximum permissible forevacuum pressure is 0.9 hPa (for N₂). p.2 ↗ | Backing pump and roughing sequencing must keep foreline pressure below 0.9 hPa during operation to avoid rotor overload. | HiPace 400 P |
| Gas throughput at final rotational speed is 2 hPa·l/s (N₂), 4 hPa·l/s (H₂, He), 1 hPa·l/s (Ar). p.2 ↗ | Defines maximum continuous process gas load; throttle gas inlet or upsize pumping train for higher throughputs. | HiPace 400 P |
| Run-up time to final speed is 1.6 min. p.2 ↗ | Short start-up enables fast cycle restarts in coating processes; gate valve interlocks should account for this delay. | HiPace 400 P |
| Standard communication interfaces are RS-485 and remote; optional fieldbuses are Profibus, Profinet, Ethercat, Devicenet and SEMI E74. p.2 ↗ | Select the matching optional interface module for PLC/fab integration; SEMI E74 variant suits semiconductor-tool recipes. | HiPace 400 P |
| Pump allows arbitrary mounting orientation. p.3 ↗ | No vertical-mount restriction simplifies integration into compact coating chambers or horizontal installations. | HiPace 400 P |
| Gas inlet is DN 100 ISO-K/ISO-F/CF-F; outlet is DN 25 ISO-KF / G 1/4". p.3 ↗ | Choose ISO-K, ISO-F or CF-F mating flanges per vacuum requirement (CF-F for high-vacuum/bakeout systems); foreline plumbing must fit DN 25 ISO-KF or G 1/4". | HiPace 400 P |
| Weight is approx. 10.9 kg. p.3 ↗ | Light enough for single-person handling and for mounting on chamber flanges without additional structural support; verify flange load limits. | HiPace 400 P |
| Sound pressure level is 50 dBA per EN ISO 2151. p.3 ↗ | Low noise allows installation in operator-accessible areas without acoustic enclosures. | HiPace 400 P |
| Hybrid bearing design supports on-site bearing change and is insensitive to process dust. p.1 ↗ | Maintenance can be performed in place without pump removal; suitable for dust-generating coating processes, but plan bearing-interval spares stock. | HiPace 400 P |
| Optional power failure venting unit and venting accessories are available. p.1 ↗ | Specify the venting unit to protect the rotor from debris/backstreaming during unplanned shutdowns in coating systems. | HiPace 400 P (option) |