No photo available yet
Agilent Technologies industrial gas analysis, composition and impurities
Agilent Technologies industrial gas analysis, composition and impurities — Gas chromatography.
The Agilent three-channel gas impurities GC analyzer is configured to UOP 1945 for trace H2, O2, N2 and extended hydrocarbons in industrial gas streams. Its 0.01 mol% typical quantitation limit distinguishes it from the CO-CO2 and polymer-characterization siblings in the same series. It serves as the composition and impurity measurement stage in gas quality monitoring systems.
Agilent Technologies Gas Impurities Measurements GC Analyzers Series — Model Comparison & Selection
| Model | Typical quantitation limit, mol% |
|---|---|
| industrial gas analysis, composition and impurities Current | 0.01 |
| CO-CO2 Analyzer, carbon monoxide analyzer | 0.01 |
Full specifications
| Typical Quantitation Limit | 0.01 mol% |
| Analyzer channels mfr | Three-channel channel |
| Configured per published method mfr | 1945 UOP |
| Analysis capacity for H2 mfr | Yes Yes |
| Analysis capacity for O2 and N2 mfr | Yes Yes |
| Extended hydrocarbon analysis mfr | Yes Yes |
Description
Construction and series positioning
- Three-channel GC architecture: separate analytical channels for H2, for O2/N2, and for extended hydrocarbon analysis, configured per UOP 1945.
- Within the series, this modification is the industrial gas composition/impurity analyzer; the CO-CO2 analyzer sibling targets carbon monoxide measurement and the polymer-characterization sibling targets polymer analysis, so channel count and target species differ.
- Typical quantitation limit is 0.01 mol%.
Analytical behavior
- The three channels run in parallel, each dedicated to its species group (H2; O2 and N2; extended hydrocarbons), so the analyzer reports composition and impurity data from one instrument rather than sequential single-channel runs.
- No digitized response curves were supplied; performance characterization rests on the 0.01 mol% typical quantitation limit and the UOP 1945 configuration.
Installation and operation
- The attached brochure digest covers the wider Agilent 8890 energy and chemical analyzer portfolio (refinery, natural gas, fuel, process gas, transformer oil and greenhouse gas options) and contains no model-specific installation, connection or control facts for this analyzer; those must be taken from the instrument manual at commissioning.
Integration & Operating Notes
Species below the 0.01 mol% typical quantitation limit cannot be reliably reported; sample conditioning and calibration must keep target impurities above this threshold or results fall outside the validated range.
Because the analyzer is configured per UOP 1945, sample pressure, purge and valve timing must follow that method; deviating from its sampling conditions invalidates the channel assignments for H2, O2/N2 and hydrocarbons.
The H2, O2/N2 and hydrocarbon channels produce separate signals that the data system must acquire and align in time; integration planning should confirm the controller can handle three simultaneous detector outputs.
Selection & Integration Q&A
Pick this model when the stream needs simultaneous trace H2, O2, N2 and extended hydrocarbon measurement per UOP 1945 at a 0.01 mol% quantitation limit. Choose the CO-CO2 sibling for carbon monoxide-focused analysis and the polymer sibling for polymer characterization; the channel count and target species differ.
Sampling must deliver gas at conditions consistent with the UOP 1945 configuration, and the data system must acquire three parallel channel signals (H2, O2/N2, hydrocarbons) with time alignment. No drive, controller or fitting part numbers are given in the supplied facts, so confirm them against the instrument manual.
The supplied facts contain no mounting, environmental or duty-cycle data for this model; the attached brochure digest covers the wider 8890 portfolio without model-specific limits. Obtain installation environment and duty-cycle requirements from the instrument manual before siting.
No maintenance intervals, consumables or accessory list are stated in the supplied facts. Columns, calibration gases and spare parts should be planned separately; consult the instrument manual for service intervals and the order documentation for what the base delivery includes.