Operating Instructions — vacuum pump (BA 232-20-EN, ed. 1.2 9.2.2018, EN)
Technical Reference Summary
Covered Models & Document Scope
Cubre las bombas de vacío rotativas de paletas lubricadas en aceite V-VC 202 y V-VC 303, incluido el diseño estándar, el diseño 'IV' (vacío final reducido, sin válvula de lastre de gas) y el diseño 'XD' (mayor compatibilidad con vapor de agua, compuertas deslizantes GF, mayor lastre de gas, mayor temperatura del cárter de aceite). Documento BA 232-20-EN, edición 1.2, 9.2.2018.
Section-by-Section Technical Breakdown
Describe la disposición de la bomba, la placa de características, la descripción funcional y las áreas de aplicación. Las bombas tienen un microfiltro en el lado de aspiración, un separador de aceite y niebla de aceite en el lado de salida, una cubierta insonorizante, un ventilador de refrigeración, una válvula de retención integral y una válvula de lastre de gas estándar. Se explican las variantes de diseño IV y XD.
- Components: A vacuum connection, B exhaust air outlet, D suction flange, E cooling air inlet, F cooling air outlet, H oil filling point, I oil sight glass, K oil discharge point, L oil separator element, M oil recommendation plate, N data plate, O rotation direction arrow, P drive motor, Q hot surfaces >70 °C, T oil remover housing, U gas ballast valve.
- Integral non-return valve prevents ventilation of the evacuated system after stop; if idle >2 minutes, ventilate connected pipe to atmospheric pressure.
- Gas ballast valve fitted as standard; reinforced gas ballast optional for higher water vapour loads.
- Design 'XD': functional parts more resistant to water steam and solvents, glass-fibre reinforced epoxy resin slide gates, increased gas ballast quantity, clearly increased oil sump temperature.
- Design 'IV': optimised for increased final pressure, no gas ballast valve, especially suitable as backing pump for a booster pump.
- Data plate includes type/size, serial number, year of construction, Data Matrix barcode, item no., speed 50/60 Hz, motor output 50/60 Hz, operating mode, suction capacity 50/60 Hz, ultimate vacuum 50/60 Hz.
Cubre la preparación, la instalación mecánica, la conexión de tuberías, el llenado de aceite y la conexión del motor. Especifica los requisitos de espacio libre, las condiciones de la base, la contrapresión admisible y las tolerancias de alimentación eléctrica.
- Machine must be freely accessible from all sides; do not close ventilation grids and holes.
- Cooling air inlets and outlets must be at least 30 cm from adjacent walls; cooling air must not be sucked in again.
- At least 50 cm space around the machine for maintenance work.
- Machine may only be operated when set up horizontally; foundation must be level, straight, at least the size of the machine and able to bear its weight.
- Installation on a firm base without anchoring is possible; on a substructure, fixing with flexible buffers is recommended.
- Above 1000 m above sea level a reduction in power is noticeable; contact manufacturer.
- Only screw pipes in by hand; counter pressures on outlet side only permissible up to +0.1 bar; prevent liquids accumulating in the exhaust line.
- Fill lubricating oil via oil filling point up to the upper edge of the sight glass.
- Electrical installation only by a specialist electrician observing EN 60204; operating company provides the main switch.
- Motors comply with DIN EN 60034, protection class IP 55, insulation class F.
- Motor must be connected via a motor protection switch; connecting cable installed via a cable fitting for strain relief.
- Without derating: ±5 % voltage deviation and ±2 % frequency deviation permissible.
Describe las comprobaciones de puesta en marcha, la verificación del sentido de giro, la puesta fuera de servicio/almacenamiento y la nueva puesta en marcha. Incluye advertencias sobre superficies calientes, ruido y aerosoles de aceite.
- Surface temperatures on marked components may exceed 70 °C at operating temperature.
- Highest noise pressure levels per EN ISO 3744 are given in Section 9; use ear protectors for long stays near the running machine.
- Extracted air contains a small residue of oil aerosols; ensure the installation room is well ventilated.
- Check rotation direction by briefly starting the motor (max. two seconds); when looking at the motor fan it must rotate clockwise.
- Use a phase sequence indicator to check direction of rotation (anti-clockwise rotating field).
- After correcting rotation direction, run motor for 2 minutes and top up oil to the upper edge of the sight glass; repeat until all oil pipes are filled; filling point must not be open when pump is running.
- Decommissioning: switch off, close cut-off devices if available, disconnect from electricity, depressurise by slowly opening pipes, remove pipes and hoses, seal suction and pressure nozzles with adhesive foil.
- Re-commissioning: check condition (cleanliness, cabling etc.) and drain preserving agents.
Proporciona intervalos de mantenimiento y procedimientos para el filtrado de aire, el acoplamiento, la lubricación y la eliminación de aceite, además de información sobre reparación/servicio y piezas de repuesto. Incluye instrucciones de seguridad para trabajos de mantenimiento.
- Monthly: check pipes and screws for leaks and proper seating; check terminal box and cable inlet holes for leaks; clean ventilation slots and motor cooling ribs.
- Depending on dirt: clean intake air filter and gas ballast valve filter.
- At least once a year: check coupling wear.
- Daily: check oil level.
- 500–2000 h: change oil; 2000 h: change oil separator elements.
- Intake air filter micro filter cleaned by rinsing or purging or replaced; check valve seating; after reassembly check valve function with a shut-off device (enclosed volume min. 1 litre) — vacuum achieved must remain constant.
- Gas ballast valve filter cartridge cleaned by purging or replaced; remove countersunk screw and plastic cover to access.
- Coupling sprocket subject to wear; defective sprockets may lead to rotor shaft breaking; clean cooling coil by purging each time.
- Oil change at operating temperature in an atmospherically ventilated area; first oil change after 500 h, subsequent after 500–2000 h.
- Recommended oils: MULTI-LUBE 100 (mineral), SUPER-LUBE 100 (synthetic, for high thermal load), ECO-LUBE 100 (synthetic, H1 certificate); viscosity must comply with ISO VG 100 per DIN ISO 3448.
- Oil separator elements (5x) replaced every 2000 operating hours or when filter resistance is 0.7 bar; use ring spanner 19 mm or 3/4", rotate counter-clockwise to remove, insert new with open lock symbol and arrow, fix clockwise until it clicks.
- For repairs use manufacturer, branch offices or authorised dealers; a signed declaration of harmlessness must accompany machines sent for service.
- Spare parts list E 232-20; only use original or manufacturer-approved parts.
Enumera el nivel de presión sonora, el peso, las dimensiones, los tamaños de conexión y la cantidad de aceite para V-VC 202 y V-VC 303. Hay datos adicionales disponibles en las hojas de datos D 232-20 y D 232-30.
- Sound pressure level (max.) per EN ISO 3744, tolerance ±3 dB(A): V-VC 202 73 dB(A) at 50 Hz, 76 dB(A) at 60 Hz; V-VC 303 73 dB(A) at 50 Hz, 77 dB(A) at 60 Hz.
- Weight: V-VC 202 195 kg at 50 Hz, 200 kg at 60 Hz; V-VC 303 200 kg at 50 Hz and 60 Hz.
- Length: V-VC 202 840 mm at 50 Hz, 925 mm at 60 Hz; V-VC 303 925 mm at 50 Hz and 60 Hz.
- Width: 523 mm for both models.
- Height (without terminal box): 402 / 480 mm (** design 'XD' with additional gas ballast valve).
- Vacuum connection and exhaust air outlet: G 2 for both models.
- Correct amount of oil: 8 l for both models.
- Length and weight may differ depending on motor manufacturer.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| La temperatura ambiente y de aspiración debe estar entre 12 y 40 °C. p.7 ↗ | Operation outside this range requires consultation with the manufacturer. | V-VC 202 and V-VC 303 |
| Medios admisibles: aire (puede contener vapor de agua pero no agua ni otros líquidos) y todos los gases secos y mezclas de gas-aire no explosivos, no inflamables, no agresivos y no venenosos. p.7 ↗ | Do not use with explosive, inflammable, aggressive or poisonous media, dust per ATEX zone 20-22, solvents, oxygen or other oxidants. | V-VC 202 and V-VC 303 |
| La contrapresión en el lado de salida no debe superar +0,1 bar. p.7 ↗ | Exhaust line must be sized and routed to avoid higher counter pressure; sealing or constricting the exhaust air outlet may lead to destruction of components. | V-VC 202 and V-VC 303 |
| La capacidad de aspiración nominal con aspiración libre es de 200 m³/h (V-VC 202) y 300 m³/h (V-VC 303) a 50 Hz. p.14 ↗ | Use data sheet D 232-20 / D 232-30 for suction capacity dependency on intake pressure. | V-VC 202 and V-VC 303 |
| Rangos de presión de admisión continua: bomba estándar 0,5 a 500 mbar (abs.); diseño 'IV' <100 mbar (abs.); diseño 'XD' 3,0 a 500 mbar (abs.). p.14 ↗ | Continuous operation outside these ranges risks oil leaking through the outlet opening. | Standard, IV and XD designs |
| Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad de aspiración nominal de la bomba de vacío. p.14 ↗ | Size the evacuated volume accordingly to avoid operational problems. | V-VC 202 and V-VC 303 |
| Para funcionamiento permanente >100 mbar (abs.), debe utilizarse la siguiente potencia de motor superior. p.14 ↗ | Motor selection must account for continuous operation above 100 mbar (abs.). | V-VC 202 and V-VC 303 |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes; al menos 50 cm de espacio alrededor de la máquina para mantenimiento. p.15 ↗ | Installation layout must provide these clearances to ensure cooling and service access. | V-VC 202 and V-VC 303 |
| La máquina solo puede operarse cuando está instalada horizontalmente; la base debe ser nivelada, recta, al menos del tamaño de la máquina y capaz de soportar su peso. p.15 ↗ | Ensure proper foundation to prevent tipping and material damage. | V-VC 202 and V-VC 303 |
| Sin reducción de potencia, se permite una desviación de tensión de ±5 % y una desviación de frecuencia de ±2 %. p.17 ↗ | Verify mains network matches motor data plate before connection. | V-VC 202 and V-VC 303 |
| Los motores cumplen con DIN EN 60034, clase de protección IP 55, clase de aislamiento F. p.17 ↗ | Electrical installation must be performed by a specialist electrician observing EN 60204. | V-VC 202 and V-VC 303 |
| La viscosidad del aceite debe cumplir con ISO VG 100 según DIN ISO 3448. p.23 ↗ | Use only suitable oil types; recommended Elmo Rietschle oils: MULTI-LUBE 100, SUPER-LUBE 100, ECO-LUBE 100. | V-VC 202 and V-VC 303 |
| Primer cambio de aceite después de 500 horas de funcionamiento; cambios de aceite posteriores después de 500–2000 horas. p.23 ↗ | Reduce change intervals depending on contamination of the discharged medium. | V-VC 202 and V-VC 303 |
| Los elementos separadores de aceite (5x) deben sustituirse cada 2000 horas de funcionamiento o cuando la resistencia del filtro sea de 0,7 bar. p.24 ↗ | Heavily contaminated air oil removing devices lead to increased pump temperatures and may cause lubricating oil to ignite spontaneously. | V-VC 202 and V-VC 303 |
| La cantidad correcta de aceite es de 8 l para ambos modelos. p.30 ↗ | Fill oil up to the upper edge of the sight glass; check oil level daily. | V-VC 202 and V-VC 303 |
| La conexión de vacío y la salida de aire de escape son G 2 para ambos modelos. p.30 ↗ | Pipe connections must match G 2 thread; only screw pipes in by hand. | V-VC 202 and V-VC 303 |
| Nivel de presión sonora (máx.) según EN ISO 3744: V-VC 202 73 dB(A) a 50 Hz, 76 dB(A) a 60 Hz; V-VC 303 73 dB(A) a 50 Hz, 77 dB(A) a 60 Hz; tolerancia ±3 dB(A). p.30 ↗ | Use ear protectors for long stays near the running machine. | V-VC 202 and V-VC 303 |
| Peso: V-VC 202 195 kg (50 Hz) / 200 kg (60 Hz); V-VC 303 200 kg (50 Hz y 60 Hz). Longitud: V-VC 202 840 mm (50 Hz) / 925 mm (60 Hz); V-VC 303 925 mm (50 Hz y 60 Hz). Anchura 523 mm. Altura 402 / 480 mm (XD con válvula de lastre de gas adicional). p.30 ↗ | Account for weight and dimensions in transport, foundation and installation planning; values may differ depending on motor manufacturer. | V-VC 202 and V-VC 303 |
| Condiciones ambientales de almacenamiento: humedad relativa 0 % a 80 %, temperatura de almacenamiento -10 °C a +60 °C. p.11 ↗ | For long-term storage (more than 3 months), use a preservation oil rather than operating oil. | V-VC 202 and V-VC 303 |
| Cuando se instala a más de 1000 m sobre el nivel del mar, se nota una reducción de potencia. p.15 ↗ | Contact manufacturer for operation at high altitude. | V-VC 202 and V-VC 303 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.27 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC/EN 60947-4-1 or VDE 0660 Part 102) | |
| Machine is switched off by the motor protection switch p.27 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Section 7.2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The air oil removers are dirty. | Change the oil separator elements | Section 7.2.4 |
| Machine is switched off by the motor protection switch p.27 ↗ | The back pressure in the exhaust line is too high. | Check the hose or the pipe | Section 5.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | Permanent operation >100 mbar (abs.). | Use next largest motor output | Section 4.3 |
| Suction capacity is insufficient p.27 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Suction capacity is insufficient p.27 ↗ | The intake filter is dirty | Clean or replace the intake filter | Section 7.2.1 |
| Final pressure (max. vacuum) is not reached p.28 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.28 ↗ | Incorrect oil viscosity | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Section 7.2.3 |
| Machine gets too hot p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| Machine gets too hot p.28 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Section 7.2.3 |
| Machine gets too hot p.28 ↗ | The air oil removers are dirty. | Change the oil separator elements | Section 7.2.4 |
| Machine gets too hot p.28 ↗ | The back pressure in the exhaust line is too high. | Check the hose or the pipe | Section 5.3 |
| Exhaust air contains visible oil mist p.28 ↗ | The air oil remover devices are not inserted correctly or the O rings are missing. | Check that it is correctly seated | Section 7.2.4 |
| Exhaust air contains visible oil mist p.28 ↗ | Unsuitable oil is being used | Use suitable types | Section 7.2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | The air oil removers are dirty. | Change the oil separator elements | Section 7.2.4 |
| Exhaust air contains visible oil mist p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| The vacuum pump produces a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the oper p.29 ↗ | The pump housing is worn (chatter marks) | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The vacuum pump produces a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the oper p.29 ↗ | The vacuum adjustment valve (if available) is vibrating | Replace the valve | Section 7.4 |
| The vacuum pump produces a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the oper p.29 ↗ | Blades are damaged | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The vacuum pump produces a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the oper p.29 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| The vacuum pump produces a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the oper p.29 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Section 7.2.3 |
| Water in lubricating oil p.29 ↗ | Pump sucks in water | Install water interceptor upstream of the pump | |
| Water in lubricating oil p.29 ↗ | The pump sucks in more water vapour than is suitable for its water vapour compatibility | Contact the manufacturer for increased gas ballast | |
| Water in lubricating oil p.29 ↗ | Pump only works for a short time and therefore does not reach its normal operating temperature | Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil |