Operating Instructions — C-DLR 401 compressor (BA 888-EN, ed. 1.1 20.6.2018, EN)
Technical Reference Summary
Covered Models & Document Scope
Este documento abarca los compresores de garra de funcionamiento sin contacto C-DLR 401 y C-DLR 501 (Serie C, diseño de garra). Ambos modelos comparten el mismo diseño y difieren en caudal (400 m3/h y 500 m3/h a 50 Hz), peso, dimensiones y nivel de potencia acústica. Se menciona una versión especial con carga de gas de sellado del área ventilada atmosféricamente entre la caja de engranajes y la cámara de compresión.
Section-by-Section Technical Breakdown
Describe la disposición de la máquina y la identificación de componentes (conexión de aspiración, conexión de presión, válvula de seguridad, entrada/salida de aire de refrigeración, punto de llenado de aceite, mirilla de aceite, punto de descarga de aceite, placa de datos, flecha de sentido de giro, filtro de aspiración, silenciador de admisión), el contenido de la placa de datos, la descripción funcional del compresor de garra de doble eje y las áreas de aplicación. Indica el rango de presión admisible, los caudales y las condiciones de funcionamiento.
- C-DLR 401 and C-DLR 501 are double-shaft rotary piston compressors with contact-free, dry claw rotors synchronised by an oil-lubricated gear pair.
- Gearbox and compression chamber are separated by special seals; an atmospherically ventilated intermediate area can be loaded with sealing gas (special version).
- Cooling is by a drum fan drawing fresh air between machine and insulating hood.
- Driven by standard flanged three-phase motors via a coupling; safety valve fitted as standard.
- Suitable for creating excess pressure between 0 and the maximum limit given on the data plate; constant operation permissible.
- Flow rates 400 m3/h (C-DLR 401) and 500 m3/h (C-DLR 501) at 50 Hz.
- Frequent switching (about 10 times an hour) or high ambient/intake temperatures may exceed motor winding and bearing temperature limits; contact manufacturer.
- Outdoor installation requires protection from environmental influences (e.g. protective roof).
Cubre la preparación para la instalación, los requisitos de montaje, la conexión de tuberías, la válvula de seguridad, el llenado de aceite y la conexión del motor. Especifica las distancias libres, las condiciones de la base, las reglas de longitud de tuberías, los requisitos de protección eléctrica y las desviaciones admisibles de tensión/frecuencia.
- Machine must be freely accessible from all sides; ventilation grids and holes must not be closed.
- Cooling air inlets and outlets must be at least 30 cm from adjacent walls; cooling air must not be recirculated.
- Minimum 40 cm in front of inlet filter and inlet silencer for maintenance.
- Machine must be set up horizontally; foundation level and straight, able to take the machine weight.
- Installation on a firm base without anchoring is possible; on a substructure fixing with flexible buffers is recommended.
- Power reduction noticeable above 1000 m above sea level; contact manufacturer.
- Do not operate without covering plates.
- Pressure connection: only screw pipes in by hand; too narrow and/or too long pressure pipe reduces volume flow.
- With connection pipes of same cross-section as machine connection and more than 3 m long, a non-return valve must be installed to avoid reverse operation when stopped.
- Safety valve is a wear part and must be replaced after 10,000 hours or no more than 2 years.
- Fill lubricating oil up to the middle of the sight glass.
- Electrical installation only by qualified electrician observing EN 60204; operating company provides main switch.
- Motors comply with DIN EN 60034, protection class IP 55, insulation class F.
- Motor protection switch required; delayed switch-off recommended due to temporary excess current at cold start.
- Without derating: ±5 % voltage deviation and ±2 % frequency deviation permissible.
Describe las comprobaciones de puesta en marcha, incluido el sentido de giro, las notas de seguridad para superficies calientes y ruido, el procedimiento de puesta fuera de servicio/almacenamiento y la nueva puesta en marcha. Especifica el sentido de giro correcto y la necesidad de esperar hasta que la máquina se detenga antes de reiniciar.
- Surface temperatures on marked components may exceed 70 °C at operating temperature.
- Highest noise pressure levels per EN ISO 3744 are given in Section 9; ear protectors recommended for long stays near running machine.
- Machine must only be switched on again after it stops.
- Intended direction of rotation shown by arrow; when looking at the motor fan it must rotate anti-clockwise.
- Start motor briefly (max. two seconds) to check rotation direction; use a phase sequence indicator (clockwise rotating field).
- Wrong direction of rotation leads to machine damage.
- Decommissioning: switch off, close cut-off devices if available, disconnect from electricity, depressurise slowly, remove pipes/hoses, seal connections with adhesive foil.
- Re-commissioning: check condition (cleanliness, cabling etc.) and follow installation and commissioning sections.
Proporciona el plan de mantenimiento, el procedimiento de cambio de aceite, la limpieza/sustitución del filtro de aire, los requisitos de reparación/servicio y la información para pedir repuestos. Incluye intervalos para comprobación de fugas, sustitución de la válvula de seguridad, comprobación del nivel de aceite, cambio de aceite y mantenimiento del filtro.
- Monthly: check pipes and screws for leaks and proper seating; check terminal box and cable inlet holes for leaks; clean safety valve and ventilation slots/motor cooling ribs; check oil level.
- Every 10,000 h: replace safety valve.
- Every 20,000 h: change oil.
- Monthly or every 6 months: clean or replace filter cartridge.
- Clean micro filter depending on how dirty the discharged medium is.
- Change oil at operating temperature and in an atmospherically ventilated area; incomplete emptying reduces refill amount.
- If changing oil type, empty oil removing device housing and oil cooler completely.
- Recommended oil: Elmo Rietschle GEAR-LUBE 150 synthetic oil; viscosity must comply with ISO VG 150 as per DIN 3448.
- Oil level in sight glasses must be checked every month; top up with machine switched off and vented to atmospheric pressure.
- Filter cartridge cleaned monthly or more often by purging from inside outwards; replace every six months.
- Filter cartridge removed after undoing tension clamps.
- Wear goggles and dust mask when cleaning with compressed air.
- For repairs use manufacturer, branch offices or authorised dealers; enclose signed declaration of harmlessness for machines sent to service centre.
- After repair or re-commissioning, carry out installation and commissioning actions as for initial commissioning.
- Order spare parts per spare parts list E 888; only use original or approved parts.
Enumera los datos técnicos clave para C-DLR 401 y C-DLR 501, incluidos los niveles de presión acústica y potencia acústica, peso, dimensiones, conexión de presión y cantidad de aceite. Hay más datos disponibles en la hoja de datos D 889.
- Sound pressure level (max.) EN ISO 3744, tolerance ±3 dB(A): 50 Hz 86 dB(A) for both models; 60 Hz 86 dB(A) for 401 and 87 dB(A) for 501.
- Sound power level: 50 Hz 99 dB(A) (401) and 101 dB(A) (501); 60 Hz 99 dB(A) (401) and 102 dB(A) (501).
- Weight: 510 kg (401), 576 kg (501).
- Length: 1295 mm (401), 1359 mm (501).
- Width: 742 mm (401), 747 mm (501).
- Height: 1123 mm (401), 1128 mm (501).
- Pressure connection: G 3.
- Correct amount of oil: 1.85 l.
- Length and weight may differ depending on motor manufacturer.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| La temperatura ambiente y de aspiración debe estar entre 5 y 40 °C. p.7 ↗ | Operation outside this range requires consultation with the manufacturer; ensure installation environment stays within limits. | C-DLR 401 and C-DLR 501 |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.14 ↗ | Maintain clearance to avoid recirculation of heated air and ensure adequate cooling. | C-DLR 401 and C-DLR 501 |
| Mínimo 40 cm de espacio libre frente al filtro de entrada y al silenciador de admisión para mantenimiento. p.14 ↗ | Plan installation layout to allow filter removal and maintenance access. | C-DLR 401 and C-DLR 501 |
| Con tuberías de conexión de la misma sección que la conexión de la máquina y de más de 3 m de longitud, debe instalarse una válvula antirretorno. p.15 ↗ | Prevents reverse operation when the machine stops; include non-return valve in piping design for long lines. | C-DLR 401 and C-DLR 501 |
| La válvula de seguridad debe sustituirse después de 10.000 horas o no más de 2 años. p.15 ↗ | Include safety valve in scheduled maintenance; it is a wear part. | C-DLR 401 and C-DLR 501 |
| Sin reducción de potencia, son admisibles una desviación de tensión de ±5 % y una desviación de frecuencia de ±2 %. p.16 ↗ | Verify site power quality against motor data plate; outside these limits requires derating or consultation. | C-DLR 401 and C-DLR 501 |
| Los motores cumplen con DIN EN 60034, clase de protección IP 55, clase de aislamiento F. p.16 ↗ | Suitable for dusty and humid environments within IP 55; ensure cable entries are sealed. | C-DLR 401 and C-DLR 501 |
| Visto desde el ventilador del motor, este debe girar en sentido antihorario; utilice un indicador de secuencia de fases (campo giratorio horario). p.18 ↗ | Incorrect rotation direction damages the machine; verify phase sequence before commissioning. | C-DLR 401 and C-DLR 501 |
| Intervalo de cambio de aceite: cada 20.000 horas de funcionamiento con operaciones limpias. p.20 ↗ | Plan oil changes at 20,000 h; use Elmo Rietschle GEAR-LUBE 150 or ISO VG 150 oil. | C-DLR 401 and C-DLR 501 |
| La viscosidad del aceite debe cumplir con ISO VG 150 según DIN 3448. p.20 ↗ | Select only compatible oil; if changing oil type, empty oil removing device housing and oil cooler completely. | C-DLR 401 and C-DLR 501 |
| El cartucho filtrante debe limpiarse mensualmente o con más frecuencia mediante soplado de dentro hacia fuera; sustituir cada seis meses. p.21 ↗ | Insufficient air filter maintenance reduces power and may damage the machine. | C-DLR 401 and C-DLR 501 |
| Cantidad correcta de aceite: 1,85 l. p.26 ↗ | Fill to middle of sight glass; use as reference for oil fill volume. | C-DLR 401 and C-DLR 501 |
| Conexión de presión: G 3. p.26 ↗ | Pipe connection must match G 3 thread; screw pipes in by hand only. | C-DLR 401 and C-DLR 501 |
| Nivel de presión acústica (máx.) a 50 Hz: 86 dB(A) para ambos modelos; a 60 Hz: 86 dB(A) para 401 y 87 dB(A) para 501. p.26 ↗ | Use ear protection for prolonged presence near running machine. | C-DLR 401 and C-DLR 501 |
| Peso: 510 kg (C-DLR 401), 576 kg (C-DLR 501). p.26 ↗ | Foundation and lifting equipment must be sized accordingly; length and weight may differ depending on motor manufacturer. | C-DLR 401 and C-DLR 501 |
| Caudales: 400 m3/h (C-DLR 401) y 500 m3/h (C-DLR 501) a 50 Hz. p.13 ↗ | Select model based on required volume flow; flow rate depends on excess pressure per data sheet D 889. | C-DLR 401 and C-DLR 501 |
| Por encima de 1000 m sobre el nivel del mar se aprecia una reducción de potencia. p.14 ↗ | Contact manufacturer for high-altitude installations; account for reduced performance. | C-DLR 401 and C-DLR 501 |
| La conmutación frecuente (aproximadamente 10 veces por hora) o las temperaturas ambiente/de aspiración elevadas pueden superar los límites de temperatura del devanado del motor y de los rodamientos. p.13 ↗ | Contact manufacturer if such conditions apply; may require special measures. | C-DLR 401 and C-DLR 501 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.24 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.24 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.24 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.24 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 102 or IEC 60947-4-1) | |
| Machine is switched off by the motor protection switch p.24 ↗ | The safety valve is dirty so that the permissible pressure is exceeded. | Clean or replace the safety valve | Section 7.2, Section 7.4 |
| Blowing capacity is insufficient p.24 ↗ | The suction filter is dirty | Clean or replace the suction filter | Section 7.2.2, Section 7.4 |
| Blowing capacity is insufficient p.24 ↗ | The pressure line is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Blowing capacity is insufficient p.24 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max excess pressure) has not been reached p.25 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max excess pressure) has not been reached p.25 ↗ | Driving power selection too low | Use next largest motor output | Data sheet D 889 |
| Machine gets too hot p.25 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.25 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.25 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| Machine gets too hot p.25 ↗ | The safety valve is dirty so that the permissible pressure is exceeded. | Clean or replace the safety valve | Section 7.2, Section 7.4 |
| The machine makes a abnormal noise p.25 ↗ | Deposits on the rotary piston | Clean the working space and the rotary piston | Elmo Rietschle Service |
| The machine makes a abnormal noise p.25 ↗ | The safety valve is vibrating | Replace the valve | Section 7.4 |