Operating Instructions — VSI 300 vacuum pump (BA 832-42-EN, ed. 1.0 20.7.2017, EN)
Technical Reference Summary
Covered Models & Document Scope
Este documento abarca la serie de bombas de vacío de tornillo S-VSI 300, incluidas la versión estándar (IV) y las variantes con recubrimiento protector contra la corrosión (XD), válvula de lastre de gas, unidad de gas de sellado, refrigeración de flujo continuo, intercambiador de calor agua/aire, intercambiador de calor agua/agua, refrigeración por circulación y unidad de control. Las opciones de motor incluyen 5.5 kW y 7.5 kW. Las instrucciones adicionales M 30, M 31, M 33 se aplican a variantes específicas.
Section-by-Section Technical Breakdown
Describe el diseño de la S-VSI 300, incluido el principio de tornillo de doble eje, la caja de engranajes lubricada por aceite y el motor trifásico embridado estándar. Cubre la información de la placa de datos, los campos de aplicación y las configuraciones de refrigeración (flujo continuo, unidad de control, refrigeración por circulación).
- Double shaft screw vacuum pump with non-touching, dry-running screw rotors.
- Gearbox and compression chamber separated by special seals; sealing gas option available.
- Data plate includes type, serial number, year, speed, motor output, operating mode, suction capacity, ultimate vacuum.
- Suitable for intake pressures 0.1 to 1000 mbar (abs.); max suction capacity 320 m3/h at 50 Hz.
- 5.5 kW motor only for continuous operation S1; max volume to evacuate closed systems 80 l.
- Cooling options: continuous flow (standard), control unit, circulation cooling.
Proporciona los requisitos para preparar el lugar de instalación, conectar las tuberías y el agua de refrigeración, llenar el aceite lubricante y conectar el motor. Incluye límites de contrapresión, calidad del agua de refrigeración y tolerancias eléctricas.
- Machine must be set up horizontally; cooling air inlets/outlets at least 30 cm from walls.
- Counter pressure limits: S-VSI 7.5 kW < +0.2 bar; S-VSI 5.5 kW < +30 mbar.
- Cooling water: pH-neutral, clean, filtered; pressure max 6 bar; temperature 15-50 °C.
- Oil filling up to middle of sight glasses; oil viscosity ISO VG 150 (CLP HC 150).
- Motor electrical data per data plate; protection class IP 55, insulation class F.
- Voltage deviation ±5%, frequency deviation ±2% permissible without derating.
Cubre la comprobación del sentido de giro, el procedimiento de postfuncionamiento para eliminar la humedad, los pasos de puesta fuera de servicio y las comprobaciones de nueva puesta en marcha. Enfatiza el sentido de giro correcto y el postfuncionamiento con aire seco.
- Check rotation direction: motor fan must rotate clockwise when looking at fan; use phase sequence indicator.
- Post-run at 50-100 mbar (abs.) with dry air for minimum 10 minutes before shutdown >2 hours.
- Decommissioning: switch off, disconnect power, depressurize, drain cooling water and condensate.
- Re-commissioning: check condition, follow installation and commissioning sections.
Enumera los intervalos de mantenimiento y los procedimientos para cambios de aceite, filtrado de aire, inspección del acoplamiento y comprobaciones del sistema de refrigeración. Especifica el cambio de aceite cada 7,500 horas de funcionamiento y la comprobación anual del acoplamiento.
- Monthly: check pipes/screws for leaks, terminal box, clean cooling ribs, check oil level, check cooling water system.
- Oil change every 7,500 operating hours; oil type ISO VG 150 (CLP HC 150).
- Clean intake air mesh filter and gas ballast valve filter depending on dirt.
- Check coupling sprocket at least once a year; replace if worn or damaged.
- Clean dirt trap in cooling circuit depending on cooling liquid quality.
Proporciona las especificaciones técnicas de la S-VSI 300 con motores de 5.5 kW y 7.5 kW, incluidos el nivel de presión sonora, el peso, las dimensiones, las conexiones, la cantidad de aceite y el consumo de agua de refrigeración.
- Sound pressure level at 200 mbar (abs.) and 0.1 mbar (abs.): 74 dB(A) at 50 Hz for both; 76 dB(A) at 60 Hz for 7.5 kW.
- Weight: 330 kg (5.5 kW), 335 kg (7.5 kW).
- Dimensions: length 1297 mm, width 454 mm, height 580 mm.
- Vacuum connection: G 2.
- Oil quantity: 1.9 l (formula: 1.1 × H + 0.8 × H1).
- Cooling water consumption: 6.7 l/min at max intake temperature 50 °C; max pressure 6 bar.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| La temperatura ambiente y de aspiración debe estar entre 5 y 40 °C. p.7 ↗ | Ensure installation environment and process gas temperature stay within this range; contact manufacturer for outside conditions. | S-VSI 300 all variants |
| Límites de contrapresión: S-VSI 7.5 kW < +0.2 bar; S-VSI 5.5 kW < +30 mbar. p.19 ↗ | Do not exceed these outlet pressures to avoid damage or reduced performance. | S-VSI 300 5.5 kW and 7.5 kW |
| La presión de servicio del agua de refrigeración no debe superar 6 bar; la temperatura debe estar entre 15 y 50 °C. p.20 ↗ | Install pressure regulation if necessary and ensure water temperature is within range. | S-VSI 300 with water cooling |
| La viscosidad del aceite debe cumplir ISO VG 150 según DIN 51519; designación CLP HC 150 (GEAR-LUBE 150 o equivalente). p.27 ↗ | Use only specified oil to ensure proper lubrication and warranty compliance. | S-VSI 300 all variants |
| Intervalo de cambio de aceite: cada 7,500 horas de funcionamiento con operaciones limpias. p.27 ↗ | Plan maintenance schedule accordingly; more frequent changes may be needed for dirty processes. | S-VSI 300 all variants |
| Protección del motor: desviación de tensión ±5%, desviación de frecuencia ±2% admisible sin reducción de potencia. p.22 ↗ | Verify power supply quality; use motor protection switch with delayed switch off. | S-VSI 300 all variants |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.18 ↗ | Ensure sufficient clearance for cooling air flow to prevent overheating. | S-VSI 300 all variants |
| La capacidad máxima de aspiración con aspiración libre es 320 m3/h a 50 Hz. p.15 ↗ | Use for sizing suction lines and system capacity; refer to data sheet for pressure-dependent curves. | S-VSI 300 all variants |
| Al evacuar sistemas cerrados, el volumen a evacuar debe ser máx. 80 l. p.15 ↗ | Do not exceed this volume for closed-system evacuation to avoid overload. | S-VSI 300 with 5.5 kW motor |
| Postfuncionamiento a 50-100 mbar (abs.) con aire seco durante mínimo 10 minutos antes de la parada >2 horas. p.24 ↗ | Prevents condensate and deposits that could block rotors on restart. | S-VSI 300 all variants |
| Consumo de agua de refrigeración: 6.7 l/min con temperatura máxima de admisión 50 °C. p.35 ↗ | Ensure cooling water supply meets this flow rate for proper cooling. | S-VSI 300 with water cooling |
| Cantidad de aceite: 1.9 l (fórmula: 1.1 × H + 0.8 × H1). p.35 ↗ | Use correct oil fill amount; check sight glasses to middle level. | S-VSI 300 all variants |
| Nivel de presión sonora: 74 dB(A) a 50 Hz tanto para 5.5 kW como para 7.5 kW; 76 dB(A) a 60 Hz para 7.5 kW. p.35 ↗ | Use ear protection when spending long time near running machine. | S-VSI 300 5.5 kW and 7.5 kW |
| Conexión de vacío: G 2. p.35 ↗ | Ensure mating pipe connection is G 2; only screw pipes in by hand. | S-VSI 300 all variants |
| Clase de protección del motor IP 55, clase de aislamiento F. p.22 ↗ | Suitable for dusty and humid environments; ensure proper electrical installation per EN 60204. | S-VSI 300 all variants |
| Ajuste de fábrica del control de temperatura: Tmax = 60 °C; ajuste de fábrica de la válvula de agua termostática: Tmax = 55 °C. p.16 ↗ | Verify settings for application; adjust if necessary. | S-VSI 300 with control unit or thermostatic water valve |
| Tensión de control de la válvula solenoide: 24 V DC. p.16 ↗ | Provide 24 V DC supply for cooling circuit control. | S-VSI 300 with control unit |
| La válvula de seguridad protege frente a una presión de agua de refrigeración > 6 bar. p.16 ↗ | Safety valve is set to limit pressure; do not exceed 6 bar supply pressure. | S-VSI 300 with water cooling |
| El piñón del acoplamiento debe comprobarse al menos una vez al año; los arranques frecuentes y la temperatura ambiente elevada reducen la vida útil. p.30 ↗ | Regular inspection prevents rotor shaft breakage due to worn coupling. | S-VSI 300 all variants |
| Temperatura de almacenamiento: -10 °C a +60 °C; humedad relativa 0% a 80%; almacenamiento no superior a 6 meses. p.11 ↗ | Store in dry, dust-free, vibration-free environment; follow storage guidelines for longer periods. | S-VSI 300 all variants |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.33 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.33 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.33 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Motor protection switch is triggered too quickly p.33 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 2 or IEC 947-4) | |
| Suction capacity is insufficient p.33 ↗ | The mesh filter is dirty | Clean or replace the mesh filter | Section 7.2.2, Section 7.4 |
| Suction capacity is insufficient p.33 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.33 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.34 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.34 ↗ | Too little cooling water | Note cooling water consumption | Section 9 |
| Final pressure (max. vacuum) is not reached p.34 ↗ | The mesh filter is dirty | Clean or replace the mesh filter | Section 7.2.2, Section 7.4 |
| Machine gets too hot p.34 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.34 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.34 ↗ | Cooling air supply is obstructed | Clean the cooling ribs | Section 7.2 |
| Machine gets too hot p.34 ↗ | The cooling water system is obstructed | Check the cooling water system and the pipes | Section 7.2 |
| Machine gets too hot p.34 ↗ | Too little cooling water | Note cooling water consumption | Section 9 |
| Machine gets too hot p.34 ↗ | Cooling water inflow is too hot | Note the max. intake temperature | Section 9 |
| The machine makes a abnormal noise p.34 ↗ | Deposits on the rotors | Clean the working space and the rotors | Elmo Rietschle Service |