Induztr
Résumé technique Visionneuse de documents Modèles associés

Operating Instructions — (EN)

Technical Reference Summary

Covered Models & Document Scope

Serie L-BV3 de bombas/compresores de vacío de anillo líquido, modelo 2BV3151. Abarca transporte, instalación, conexión eléctrica, conexión de tuberías/mangueras, puesta en marcha, operación (autoaspirante y con alimentación de líquido de servicio, no automática y automática), parada, mantenimiento y solución de problemas. Datos eléctricos según la placa de características del motor de accionamiento; los modelos especiales pueden tener pesos superiores.

Section-by-Section Technical Breakdown

pp. 7-8
Datos técnicos

Datos mecánicos, pares de apriete, referencia de datos eléctricos y condiciones de operación para el 2BV3151. Incluye peso, distancia mínima de disipación de calor, nivel de ruido, límites de temperatura y presión, y cantidades de líquido.

  • Weight approx. 9 kg (19.8 lbs); higher weights possible with special models.
  • Minimum distance from fan guard to adjacent surface: 20 mm (0.787 in).
  • 1-m measuring-surface sound pressure level: 70 dB(A) at 50 Hz and 70 dB(A) at 60 Hz.
  • Operating speed: see rating plate; exceeding it increases noise, vibration and reduces bearing/grease life.
  • Tightening torques: G1/8 pipe connections 4.5 Nm ±10%; G3/8 pipe connections 16 Nm ±10%; M4 terminal board 1.0 Nm; M5 terminal board 2.2 Nm; M3 modular terminal blocks 0.6 Nm.
  • Pumped gas/vapor temperature max. +110 °C (+230 °F); operating-liquid temperature +5 to +40 °C (nominal +15 °C); ambient temperature +5 to +40 °C.
  • Min. inlet pressure during vacuum operation without cavitation protection: 5 kPa (0.725 psi); with cavitation protection: max. achievable vacuum.
  • Max. discharge pressure during vacuum operation: 110 kPa abs. (16.0 psia); max. differential pressure during compressor operation: 60 kPa (8.70 psi); max. permissible internal pressure during compressor operation: 300 kPa abs. (43.5 psia).
  • Nominal operating-liquid flow rate: 0.65 l/min (0.039 m³/h); max. filling quantity at standstill: 0.200 l; max. water entrained via inlet: 3.9 l/min.
pp. 9
Modos de operación

Describe los dos modos principales de operación: funcionamiento autoaspirante y funcionamiento con alimentación de líquido de servicio, este último subdividido en operación no automática (válvula de cierre manual) y automática (electroválvula vinculada al motor).

  • Self-priming operation: pump automatically sucks in operating liquid; flow rate self-adjusts.
  • Operation with operating-liquid feed: operating liquid is not self-primed; a nominal flow rate or pre-pressure must be set.
  • Non-automatic operation: operating-liquid feed switched manually with a stop valve.
  • Automatic operation: solenoid valve opens when motor is switched on and closes when motor is switched off.
pp. 11-15
Instalación

Abarca la instalación mecánica, la conexión eléctrica del motor y la conexión de tuberías/mangueras para entrada, descarga y líquido de servicio. Incluye distancias mínimas, límites de vibración, distancias eléctricas y pares de apriete.

  • Install on flat, level, stationary surfaces at max. 1000 m (3280 ft) above sea level.
  • Maintain minimum distance of 20 mm from fan guard to adjacent surface; do not re-suck discharge air of other units.
  • Maximum permissible vibration velocity veff = 4.5 mm/s (0.177 in/s).
  • Secure all feet with screws through all mounting holes.
  • Electrical supply tolerances: ±5% voltage deviation, ±2% frequency deviation.
  • Clearance between bare live parts and to ground: ≥5.5 mm at UN ≤690 V.
  • Use motor circuit breakers set to the nominal current on the rating plate.
  • Pipe connections: inlet G3/8 (12 mm deep), discharge G3/8 (12 mm deep), operating-liquid port G1/8 (10 mm deep), cavitation protection G1/8 (10 mm deep), drain hole G1/8 (10 mm deep).
  • Tightening torque for G3/8 intake and discharge connections must not exceed 16 Nm ±10%.
  • Install a check valve when connecting to a vacuum accumulator.
  • Install a start-up screen in the inlet pipe for the first 100 operating hours.
pp. 16-19
Puesta en marcha

Procedimientos de preparación y arranque para el funcionamiento autoaspirante y el funcionamiento con alimentación de líquido de servicio. Incluye llenado con líquido de servicio, verificación del sentido de giro y ajuste del caudal de líquido de servicio.

  • Do not switch on unless the unit is filled with operating liquid; dry running destroys the mechanical seal in seconds.
  • For self-priming operation, fill operating liquid during installation before connecting pipes/hoses.
  • For operation with operating-liquid feed, fill after completing installation via the cavitation protection hole.
  • Check direction of rotation by briefly switching on and comparing external fan rotation with the arrow on the housing.
  • Self-priming operation: inlet must be pre-throttled to at least 80 kPa abs. (11.6 psia) at switch-on; liquid level at switch-on must equal shaft center; during operation reservoir level may not drop below approx. 1 m (3.28 ft) below shaft center.
  • Operation with operating-liquid feed: set pre-pressure pA ≈ pB + 100 kPa (14.5 psi) above inlet pressure, or measure and set flow rate via flow meter or graduated vessel.
  • Nominal operating-liquid flow rate: 0.65 l/min.
pp. 24-26
Mantenimiento y solución de problemas

Contenido de mantenimiento y reparación/solución de problemas. Incluye una tabla de fallos con síntomas, causas, remedios y quién puede realizar el trabajo.

  • Fault table covers motor not starting, humming noises, jammed impeller, defective impeller and defective motor bearings.
  • Electrical faults must be remedied by an electrician; mechanical faults by operator or service as indicated.
  • Decalcification and cleaning procedures are referenced to Chapter 10.1, Maintenance, Pg. 24.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
El peso del 2BV3151 es aprox. 9 kg (19.8 lbs); pesos superiores posibles con modelos especiales. Verify load-bearing capacity of installation surface and select lifting equipment accordingly. 2BV3151
La distancia mínima desde la protección del ventilador hasta la superficie adyacente es de 20 mm (0.787 in). Maintain clearance to ensure sufficient cooling and prevent overheating. 2BV3151
El nivel de presión sonora en superficie de medición a 1 m es de 70 dB(A) tanto a 50 Hz como a 60 Hz. Use for acoustic planning and hearing protection assessment. 2BV3151
Pares de apriete: conexiones de tubería G1/8 4.5 Nm ±10%; conexiones de tubería G3/8 16 Nm ±10%; placa de bornes M4 1.0 Nm; placa de bornes M5 2.2 Nm; bloques de bornes modulares M3 0.6 Nm. Use correct torque to avoid leakage or damage to connections. 2BV3151
Temperatura máxima del gas/vapor bombeado +110 °C (+230 °F); temperatura del líquido de servicio +5 a +40 °C (nominal +15 °C); temperatura ambiente +5 a +40 °C. Ensure process and ambient conditions stay within these limits; at >80 °C consider increased operating-liquid flow or series capacitor. 2BV3151
Presión mínima de entrada durante operación de vacío sin protección contra cavitación: 5 kPa (0.725 psi); con protección contra cavitación: vacío máximo alcanzable. Do not operate below 5 kPa abs. without cavitation protection to avoid cavitation damage. 2BV3151
Presión máxima de descarga durante operación de vacío: 110 kPa abs. (16.0 psia); presión diferencial máxima durante operación de compresor: 60 kPa (8.70 psi); presión interna máxima admisible durante operación de compresor: 300 kPa abs. (43.5 psia). Provide protective devices if system pressures can exceed these limits. 2BV3151
Caudal nominal de líquido de servicio: 0.65 l/min (0.039 m³/h); cantidad máxima de llenado en parada: 0.200 l; agua máxima arrastrada por la entrada: 3.9 l/min. Set operating-liquid flow to nominal value; install upstream separator if entrained water can exceed 3.9 l/min. 2BV3151
Velocidad de vibración máxima admisible veff = 4.5 mm/s (0.177 in/s). Ensure installation and system vibrations do not exceed this value for proper operation and long service life. 2BV3151
Tolerancias de alimentación eléctrica: desviación de tensión ±5% y desviación de frecuencia ±2% admisibles sin reducción del rendimiento. Verify supply quality; larger deviations may require consultation with Service Department. 2BV3151
Distancia entre partes activas desnudas y entre partes activas desnudas y tierra: ≥5.5 mm a tensión nominal UN ≤690 V. Maintain minimum electrical clearance during wiring to ensure safety. 2BV3151
Conexiones de tubería: entrada G3/8 (12 mm de profundidad), descarga G3/8 (12 mm de profundidad), puerto de líquido de servicio G1/8 (10 mm de profundidad), protección contra cavitación G1/8 (10 mm de profundidad), orificio de drenaje G1/8 (10 mm de profundidad). Select mating fittings and pipes accordingly. 2BV3151
El par de apriete para las conexiones de aspiración y descarga G3/8 no debe superar 16 Nm ±10% (11.8 ft lbs ±10%). Avoid over-tightening to prevent damage to connections. 2BV3151
El funcionamiento autoaspirante requiere que la entrada esté preestrangulada al menos a 80 kPa abs. (11.6 psia) en el momento del encendido; el nivel de líquido en el encendido debe ser igual al centro del eje; durante la operación el nivel del depósito no puede descender por debajo de aprox. 1 m (3.28 ft) por debajo del centro del eje. Design feed pipe and reservoir to meet these levels for reliable self-priming. 2BV3151
Funcionamiento con alimentación de líquido de servicio: ajustar la contrapresión pA ≈ pB + 100 kPa (14.5 psi) por encima de la presión de entrada, o medir y ajustar el caudal mediante caudalímetro o recipiente graduado. Use method A or B to establish correct operating-liquid flow. 2BV3151
Instalar una válvula de retención al conectar la bomba a un acumulador de vacío. Prevents operating liquid from being sucked into the system. 2BV3151
Instalar un tamiz de arranque en la tubería de entrada durante las primeras 100 horas de operación. Prevents installation residues from entering the unit. 2BV3151
Utilizar interruptores automáticos de motor ajustados a la corriente nominal especificada en la placa de características. Provides correct motor overload protection. 2BV3151

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
Motor does not start, no running noise. p.26 ↗ Interruption of the power supply, with single-phase model in one cable, with two-phase model in at least two cables. Check fuses, terminals and cables for open circuit. Eliminate open circuit. Carried out by: Electrician
Motor does not start, humming noises. p.26 ↗ One power supply lead interrupted. Check fuses, terminals and cables for open circuit. Eliminate open circuit. Carried out by: Electrician
Impeller is jammed. p.26 ↗ Impeller is jammed. Free shaft by turning. See Chapter 10.1, "Maintenance", Pg. 24. Carried out by: Operator
Impeller is jammed. p.26 ↗ Impeller is jammed. Decalcify vacuum pump/compressor. See Chapter 10.1, "Maintenance", Pg. 24. Carried out by: Operator
Impeller is jammed. p.26 ↗ Impeller is jammed. Drain and clean vacuum pump/compressor if necessary. See Chapter 10.1, "Maintenance", Pg. 24. Carried out by: Operator
Impeller is jammed. p.26 ↗ Impeller is jammed. Check and correct impeller gap setting if necessary. Carried out by: Service
Impeller defective. p.26 ↗ Impeller defective. Replace impeller. Carried out by: Service
Motor bearings defective. p.26 ↗ Motor bearings defective. Replace motor bearings. Carried out by: Service