No photo available yet
Agilent Technologies HLD BR15
Agilent Technologies HLD BR15 — Vacuum technologies.
The HLD BR15 is a benchtop helium mass spectrometer leak detector built around a 50 L/s diffusion pump, positioned in the HLD series between the portable PR02/PD03 and the higher-throughput BR30. It serves as the rapid-cycle bench unit for production leak testing where oil-based high vacuum is acceptable.
Agilent Technologies Helium Mass Spectrometer Leak Detectors Hld Series — Model Comparison & Selection
| Model | Diffusion pump pumping speed, L/s |
|---|---|
| HLD BR15 Current | 50 |
| Helium Leak Detector, Benchtop, HLD BR30, Rapid Test Cycle | 50 |
Full specifications
| Diffusion Pump Pumping Speed | 50 L/s |
| Vacuum gauge measurement range mfr | 6 pressure |
| Dry scroll pump typical size mfr | 3...30 h |
| Turbomolecular pump pumping speed mfr | 70...3 L/s |
| Turbomolecular pump controller protection class mfr | 54 |
| Touchscreen languages mfr | 8 languages |
| Warranty mfr | 2 years |
Description
Construction and series positioning
- Benchtop (B) chassis with a diffusion (R) high-vacuum pump; the matched spec gives a diffusion-pump pumping speed of 50 L/s.
- Sits in the HLD bench family alongside the BR30 (rapid test cycle) and the dry-pump BD15/BD30; the BR15 is the diffusion-pumped bench unit, while the BD variants use oil-free dry pumps and the MR15 is the mobile configuration.
- The model code BR15 is a size/configuration code, not a rating; electrical ratings are not stated in the verified facts and are therefore not asserted here.
Behavior and operating envelope
- The verified fact set contains no curve points and no complete pressure-range table, so no sensitivity, minimum detectable leak rate or inlet-pressure envelope is stated.
- The extra factory specs list a vacuum gauge measurement range value of 6 and a pumping speed value of 2 with mismatched units (pressure vs h), which cannot be reconciled; these parameters are omitted rather than guessed.
- The turbomolecular pump pumping speed field reads "70...3" L/s and the dry scroll pump size reads "3...30" h; both are internally inconsistent and are not presented as this model's specifications.
Installation, control and operation
- The attached brochure digests contain no model-specific installation, connection or control facts for the BR15; they are marketing-level documents without ordering codes or technical tables.
- The only control-related fact is a touchscreen available in 8 languages; the turbomolecular pump controller protection class is given as 54 (IP 54).
- Warranty is stated as 2 years.
Integration & Operating Notes
Operator interface is a touchscreen with 8 selectable languages. No digital I/O, fieldbus or remote-control protocol is documented in the verified facts, so any plant-level integration must be confirmed against the full manual before the unit is specified into an automated line.
The verified fact set does not state an input voltage or current for the BR15, and the model number is a size code, not a voltage. The electrical configuration must be taken from the order documentation or nameplate rather than inferred from the series brochure.
Warranty is 2 years. No maintenance interval, consumable list or error-code table for the BR15 appears in the attached brochure digests, so the preventive-maintenance plan (pump oil, filters, calibration) must be drawn from the full instruction manual at handover.
Selection & Integration Q&A
Pick the BR15 when a diffusion-pumped benchtop unit with a 50 L/s high-vacuum stage fits the test cell and oil-vapor tolerance is acceptable. Choose BR30 for a faster test cycle, or BD15/BD30 where an oil-free dry pump is mandatory; MR15 is the mobile variant.
The verified data gives no input voltage, current or I/O protocol for this model, so the supply and any line-side controller must be confirmed from the order documentation and nameplate. The turbomolecular pump controller is rated protection class 54 (IP 54); mating inlet flange and backing-stage requirements are not stated in the available facts.
It is a benchtop unit, so it is placed on a stable lab or production bench rather than integrated as a mobile cart (that is the MR15 role). The attached brochure digests contain no ambient-temperature, duty-cycle or vibration limits, so those must be read from the full instruction manual before continuous production use.
Warranty is 2 years. The verified documents list no consumables, cables or calibration accessories as included, and give no service interval; pump oil, filters and calibration leaks should be treated as separately specified items and the maintenance schedule taken from the full manual.