Agilent Technologies 5977A GC MSD
Agilent Technologies 5977A GC MSD — Gas chromatography.
The 5977A GC MSD is a single-quadrupole mass-selective detector with a diffusion high-vacuum pump, rated for maximum recommended helium flow of 1.5 mL/min and maximum column id of 0.25 mm. It is not CI-capable; CI requires a turbo-pump sibling. It serves as the mass-selective detector in a GC/MS system for EI-mode analysis.
Full specifications
| Gas Flow | 2 mL/min |
| High Vacuum Pressure | Only with Micro-Ion vacuum gauge installed. |
| Maximum Recommended Gas Flow | 1.5 mL/min |
| Optimal He Column Flow | 1 mL/min |
| Max column id mfr | 0.25 mm |
| CI capability mfr | No No |
| Inert ion sources available mfr | Yes Yes |
| GC compatibility mfr | 9000 |
| Foreline pumps available mfr | Pfeiffer Duo Duo |
| DIP capability (3rd party) mfr | Yes Yes |
| High vacuum pump mfr | Diffusion Diffusion |
| Turbo Pump Speed mfr | Displays the turbo pump speed. speed. |
| Foreline Pressure mfr | Displays the foreline pressure. pressure. |
| CI Reagent mfr | Displays CI reagent gas and flow rate . |
| CI capability‡ mfr | No No |
| DIP** capability (3rd party) mfr | Yes Yes |
| Carrier gas purity minimum mfr | 99.9995 |
| JetClean default hydrogen flow mfr | 0.13 |
| PCI recommended reagent gas flow mfr | 20 |
| NCI recommended reagent gas flow mfr | 40 |
| Reagent gas line evacuation time mfr | 6 minutes |
| Post-pumpdown thermal equilibration wait mfr | 2 hours |
| CI bakeout time before tuning mfr | 2 hours |
| Hydrogen dissipation wait after power failure mfr | 10 minutes |
| MSD cool-down wait after power failure mfr | 1 hour |
| Depth | 54 cm |
| Foreline Pump Weight | 11 kg |
| Height | 41 cm |
| Weight | 39 kg |
| Width | 30 cm |
| MSD housing height mfr | 41 cm |
| MSD housing width mfr | 30 cm |
| MSD housing depth mfr | 54 cm |
| Diffusion pump mainframe weight mfr | 39 kg |
| EI/CI turbo pump mainframe weight mfr | 46 kg |
| Primary fuse rating mfr | 12.5 V |
| Sound pressure | 70 dB |
| Standard EI turbo pump mainframe weight mfr | 44 kg |
Description
Construction and series positioning
- The 5977A GC MSD is the diffusion-pump variant of the 5977 single-quadrupole series, sharing the 41 cm high × 30 cm wide × 54 cm deep housing with turbo-pump siblings but weighing 39 kg versus 44–46 kg for turbo models.
- It is limited to electron ionization (EI); chemical ionization (CI) is available only on turbo-pump models (G7077B, G7078B, G7079B, G7081B).
- The diffusion pump restricts maximum recommended helium flow to 1.5 mL/min (absolute maximum 2 mL/min) and maximum column id to 0.25 mm (30 m), versus 4 mL/min and 0.53 mm for turbo models.
Behavior under load and media limits
- Total gas flow into the MSD—column flow plus any reagent gas—must be summed against the 1.5 mL/min recommended limit; exceeding it degrades spectral performance and sensitivity.
- With hydrogen or methane, total flow to the MS must never exceed 50 mL/min, including column and reagent gas, to limit explosion risk.
- The instrument is not CI-capable, so no reagent-gas flow control module or CI source is present; the vacuum gauge controller (G3397B) is recommended for EI to monitor vacuum but is mandatory only for CI.
Installation, control and operation
- The MSD operates from the data system, the GC control panel, or the local control panel (LCP), with front-panel LEDs indicating status and mode.
- Pump-down, venting, temperature setting, autotune, and flow control are performed through these interfaces; the side-plate O-ring requires only a very light coat of Apiezon L high-vacuum grease (shiny appearance indicates excess).
- Primary fuses are T12.5A, 250 V (part 2110-1398), two required; fuse failure most often indicates a foreline-pump problem.
- The foreline pump (Pfeiffer Duo, 11 kg) is separate from the 39 kg MSD mainframe and must be accommodated on the bench.
Integration & Operating Notes
The diffusion pump cannot handle higher gas loads: sum column flow and any reagent gas against the 1.5 mL/min recommended maximum (2 mL/min absolute). Exceeding these flows will likely cause spectral degradation and reduced sensitivity, so column dimensions must also respect the 0.25 mm id limit.
When using hydrogen or methane as carrier or reagent gas, the combined flow to the MS must never exceed 50 mL/min. This is an explosion-safety limit, not a performance limit; configure and monitor flows accordingly, and after venting with hydrogen open the analyzer side plate at least 45 degrees for 10 minutes before powering on.
Foreline pump oil must be replaced every 6 months (every 3 months if using ammonia reagent gas, though this model is not CI-capable). Check foreline pump fluid weekly and check for leaks monthly. Diffusion pump fluid and dry foreline pump seals are annual items; IDP-3 tip seal annually.
The quadrupole mass filter requires no periodic maintenance and must never be cleaned or adjusted outside Agilent service; the HED ceramic insulator must never be touched. Wear a grounded antistatic wrist strap before opening the analyzer chamber to prevent ESD damage to the side board.
Two primary fuses of type T12.5A, 250 V (part 2110-1398) are required. A blown primary fuse most likely indicates a problem with the foreline pump, so investigate the pump before replacing fuses and restarting.
Selection & Integration Q&A
Choose the diffusion-pump model for EI-only work with helium flows ≤1.5 mL/min and columns ≤0.25 mm id. If you need CI (PCI/NCI), wider 0.53 mm columns, or flows up to 4 mL/min, select a turbo-pump sibling such as G7077B, G7078B, G7079B, or G7081B; CI is not available on diffusion-pump models.
A Pfeiffer Duo foreline pump (11 kg) is used with this model. The high-vacuum gauge controller (G3397B) is recommended for EI to monitor vacuum, though mandatory only for CI. The MSD is compatible with 9000 GCs; ensure column id ≤0.25 mm and total helium flow ≤1.5 mL/min to match the diffusion pump capacity.
Bench must support the 39 kg mainframe (41×30×54 cm) plus the 11 kg foreline pump, with access for weekly fluid checks. With hydrogen, total flow to the MS must never exceed 50 mL/min, and after venting open the side plate ≥45° for 10 minutes before power-on. Fasten the top thumbscrew finger-tight when using hazardous gas.
Plan for foreline pump oil changes every 6 months, weekly fluid checks, monthly leak checks, annual diffusion pump fluid and dry foreline pump seal replacement, and annual IDP-3 tip seal. Consumables include Apiezon L high-vacuum grease for the side-plate O-ring and T12.5A, 250 V fuses (part 2110-1398, 2 required); these are not included in the base instrument.