Nabertherm R 170/1000/13
Nabertherm R 170/1000/13 — Tube furnaces.
The R 170/1000/13 is a compact tube furnace with a 170 mm outer tube diameter and a 1000 mm heated length, rated to 1300 °C and connected via a 3-phase supply. Its 1400 mm tube length and constant-temperature lengths of 330 mm and 500 mm distinguish it within the R series from smaller-bore siblings such as the R 50/250/13 and R 50/500/12.
Nabertherm Compact Tube Furnaces up to 1300 °C | Nabertherm Series — Model Comparison & Selection
| Model | Electrical connection | Max temperature, °C | Weight, kg |
|---|---|---|---|
| R 170/1000/13 Current | 3-phase | 1300 | 89 |
| R 50/250/13 | 1-phase | 1300 | 22 |
| R 50/500/12 | 1-phase | 1200 | 34 |
Full specifications
| Electrical connection | 3-phase |
| Outer tube Ø mfr | 170 |
| Heated mfr | 1000 |
| Connected mfr | 13.7 |
| Outer dimensions (W × D × H) mfr | 460 × 628 mm |
| Weight | 89 kg |
| Length constant1 mfr | 330 |
| Length constant1 mfr | 500 |
| Tube length mfr | 1400 |
| Max temperature | 1300 °C |
Description
Construction and series positioning
- The R 170/1000/13 is the large-bore, long-heated-zone member of Nabertherm's compact tube furnace series, with a 170 mm outer tube diameter and a 1000 mm heated length.
- It differs from the sibling R 50/250/13 and R 50/500/12 by tube diameter (170 mm vs 50 mm) and heated length (1000 mm vs 250/500 mm), making it the choice for larger workpieces or higher throughput rather than small-sample work.
- The 1400 mm overall tube length provides 200 mm of cold tube beyond each end of the heated zone for gas connections and seals.
- The unit weighs 89 kg and has outer dimensions of 460 × 628 mm (W × D); height is not stated in the verified facts.
Thermal behavior
- Maximum working temperature is 1300 °C. No heating or cooling curve points were supplied, so no rate figures are asserted here.
- Two constant-temperature lengths are listed, 330 mm and 500 mm; the conditions distinguishing these two values are not stated in the verified facts, so both are reported as given rather than reconciled.
Electrical and control
- The furnace is connected to a 3-phase supply; the connected load is listed as 13.7 without a unit in the source, so the unit is not asserted here.
- No controller, thermocouple type, or interface details specific to this model are present in the verified facts; the attached controller document covers the 500-series controllers and MyNabertherm app generically and does not name this furnace.
Integration & Operating Notes
The furnace is specified for 3-phase connection. Before installation, verify that the available supply matches the phase configuration and protective device rating of the unit as delivered; the verified facts do not state voltage or frequency, so these must be taken from the nameplate.
The maximum temperature of 1300 °C is the upper limit for the furnace and the work tube. Operation above this value risks tube failure and invalidates the thermal specification; the controller setpoint and any over-temperature protection should be configured so the limit cannot be exceeded.
Selection & Integration Q&A
Pick the R 170/1000/13 when the workload needs a 170 mm tube bore and a 1000 mm heated length, e.g. larger parts or longer residence in the hot zone. The R 50 siblings have 50 mm bores and 250 or 500 mm heated lengths, suited to small samples.
It needs a 3-phase supply; voltage and frequency are not stated in the verified facts and must be read from the nameplate. No controller or thermocouple is specified for this model in the supplied documents, so control hardware must be selected separately.
The verified facts list only the furnace itself; no work tube, controller, thermocouple, gas fittings, or cables are confirmed as included. These must be specified separately, and no maintenance interval is stated in the supplied documents.