Agilent Technologies Scroll Pumps for Helium Recirculation & Cryogenic Applications
Agilent Technologies ·Made in USA · In Active Production

Agilent Technologies Scroll Pumps for Helium Recirculation & Cryogenic Applications

Agilent Technologies Scroll Pumps for Helium Recirculation & Cryogenic Applications — Vacuum technologies with Motor power 0.119 kW, Pumping speed 3.6 m³/h.

The Agilent IDP dry scroll pump is an oil-free, hermetic roughing pump for helium recirculation and cryogenic service. This configuration delivers 60 L/min pumping speed and 3.3 mbar base pressure from a 0.16 HP motor at 100 VAC. It sits in the IDP family alongside the 2.1, 5.4, 20.60 and 26.48 CFM variants, covering small-to-mid laboratory vacuum duties.

Motor power
0.119 kW
Pumping speed
3.6 m³/h

Agilent Technologies Idp Pumps Series — Model Comparison & Selection

Model Motor power, kWUltimate pressure, mbarPumping speed, m³/hBase pressure, mbarSupply frequency, HzOperating temperature, °C
Scroll Pumps for Helium Recirculation & Cryogenic Applications Current 0.119—3.63.3——
20.60 CFM 0.1193.33.63.350—
26.48 CFM 0.1193.33.63.350—
6.0 CFM ——————
IDP-4 0.1192.43.63.3—5

Full specifications

Core Performance & Functional Specifications
Motor power 0.16 HP
Pumping speed 60 L/min
Base Pressure 3.3 mbar
IDP-10 mfr 3810
IDP-10 with inlet isolation valve mfr 3810
IDP-7/10 tip seal replacement kit mfr 3807
Exhaust silencer kit mfr 110
Purge kit mfr 3807
Gas ballast kit mfr 3807
Inlet trap mfr 25
Vibration isolation kit mfr 110 VIBISOKIT
IDP-35 mfr 3835
IDP-35 with Gauge mfr 3835
IDP-35 with Inlet Valve mfr 3835
IDP-35 with Inlet Valve and Gauge mfr 3835
Inlet HEPA filter, NW40 mfr 40
HEPA filter, NW25 mfr 25
IDP-45 mfr 3845
IDP-45 with Gauge mfr 3845
IDP-45 with Inlet Valve mfr 3845
IDP-45 with Inlet Valve and Gauge mfr 3845
IDP-15 mfr 3815
IDP-15 with inlet isolation valve mfr 3815
IDP-15 tip seal replacement kit mfr 3815
IDP-3 mfr Vibration isolation kit kit
IDP-4 mfr Replacement filter element element
IDP-7 mfr Vibration isolation kit kit
inlet valve closing time mfr 20 milliseconds
inlet valve opening time after power restore mfr 10 seconds
tip seal replacement duration mfr half an hour hour
IDP-4 maintenance duration mfr 15...30 minutes
integrated Pirani gauge pressure range mfr -4...1000 mbar
VPI valve isolation time mfr 20 ms
Electrical, Power & Drive Specifications
Operating voltage mfr 100 VAC
IDP-35/IDP-45 supply frequency mfr 50 Hz

Description

Construction and series positioning

Behavior and operating envelope

Electrical and control specifics

Installation and operation

Integration & Operating Notes

Electrical
Confirm the 100 VAC nameplate variant before connection

The IDP family is offered with 100–120/200–240 VAC motor variants and a 24 VDC drive on the IDP-3. Applying a supply outside the nameplate rating of the specific unit ordered will damage the motor. Verify the variant on the label before wiring, and do not assume the 100 VAC figure applies to every IDP pump.

Agilent IDP dry scroll pump family brochure 5991-7583EN
Maintenance
Scroll service intervals are not defined in the family digest

The available document digest contains no section-level maintenance schedule, tip-seal replacement interval or error-code table for this model. Obtain the full instruction manual before commissioning to establish preventive-maintenance intervals and spare-parts list; do not extrapolate intervals from other IDP sizes.

Agilent IDP dry scroll pump family brochure 5991-7583EN
Mounting
Mounting orientation and inlet/outlet fittings are manual-defined

No mounting-orientation, clearance or flange data is present in the available digest for this configuration. Confirm baseplate or bench mounting, inlet flange type and exhaust connection from the unit's manual before designing the foreline and exhaust routing.

Agilent IDP dry scroll pump family brochure 5991-7583EN

Selection & Integration Q&A

When should I choose this 60 L/min IDP configuration instead of the 20.60 or 26.48 CFM siblings?

All three share 0.16 HP and 3.3 mbar base pressure, so the decision is throughput. Pick this 60 L/min unit for small chambers and helium recirculation loops where 2.1 CFM is sufficient; move to the 20.60 or 26.48 CFM variants when pump-down time or gas load demands higher speed at the same ultimate pressure.

What supply and foreline components must match this pump?

The unit is a 100 VAC variant, so the supply must match its nameplate; the family also includes 100–120/200–240 VAC and 24 VDC (IDP-3) drives, which are not interchangeable. Inlet and exhaust fittings are manual-defined, and with a 3.3 mbar base pressure any process needing lower pressure requires an additional high-vacuum stage downstream.

What mounting and duty-cycle limits apply to this model?

The available family digest gives no mounting orientation, clearance or duty-cycle data for this configuration. Before installation, consult the full instruction manual for allowable tilt, ambient temperature and continuous-operation limits; do not assume the pump may be mounted in any orientation or run continuously without confirmation.

What maintenance and accessories are needed beyond the base pump?

The digest lists no tip-seal kit, inlet filter, exhaust hose or cable as included, and no service interval is documented for this model. Obtain the full manual to establish scroll-tip-seal replacement intervals and the spare-parts list, and budget for foreline fittings and exhaust lines separately from the pump.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Agilent IDP-4 Dry Scroll Vacuum Pump
Brochure ·10,7 МБ ·11 pp.
View PDF