Elmo Rietschle 2BV3151
Elmo Rietschle ·Made in Germany · In Active Production

Elmo Rietschle 2BV3151

Elmo Rietschle 2BV3151 — Liquid Ring Vacuum Pumps.

The 2BV3151 is a liquid-ring vacuum pump in the L-2BV series, achieving an ultimate pressure of 33 mbar abs. with a nominal operating-liquid flow of 0.65 l/min. It is distinguished from siblings by its G3/8 inlet/discharge ports and 9 kg weight, serving as a compact solution for self-priming or operating-liquid-fed vacuum systems.

Elmo Rietschle L-2BV Series — Model Comparison & Selection

Model Max inlet pressure, kPaOperating principleWeight, kgNoise level, dBOperating temperature, °CPumping speed, m³/h
2BV3151 Current —Liquid ring vacuum pump970——
L-2BV 3151 3.3—97011039
L-2BV 7060 130liquid-ring257080—

Full specifications

Core Performance & Functional Specifications
Operating principle Liquid ring vacuum pump
Ultimate pressure 33 mbar abs.
Dimensions, Weight & Mechanical Design
Weight 9 kg
Electrical, Power & Drive Specifications
Power supply AC
Operating Conditions, Environment & Protection
Noise level 70 dB(A) (50 Hz)
60 Hz: 70 dB(A)
Protection rating IP55

Description

Construction and Series Positioning

The 2BV3151 is a liquid-ring vacuum pump from the Elmo Rietschle L-2BV series. It weighs 9 kg and has an IP55-rated motor. The pump is optimized for vacuum generation with an ultimate pressure of 33 mbar abs. This model uses G3/8 inlet and discharge connections, G1/8 operating-liquid and cavitation-protection ports, and a G1/8 drain hole.

Operating Behavior and Limits

Installation and Operation

Installation requires a minimum clearance of 20 mm from the fan guard to adjacent surfaces for cooling, and the mounting surface must support the 9 kg weight. The pump must be installed so that vibration velocity does not exceed 4.5 mm/s. Electrical connection requires a motor circuit breaker set to the rating plate current, and supply voltage/frequency deviations must stay within ±5% and ±2%, respectively. Pipe connections must be tightened to the specified torques: G3/8 to 16 Nm ±10%, G1/8 to 4.5 Nm ±10%. A check valve is recommended when connecting to a vacuum accumulator, and a start-up screen should be installed in the inlet pipe for the first 100 operating hours.

Integration & Operating Notes

Mounting
Maintain 20 mm clearance from fan guard

Insufficient clearance can cause overheating and reduced service life. Ensure at least 20 mm (0.787 in) between the fan guard and any adjacent surface to allow adequate cooling airflow.

Operating Instructions, Chapter 3.1, Pg. 7
Process Limits
Do not exceed 110 kPa abs. discharge pressure

During vacuum operation, the maximum discharge pressure is 110 kPa abs. (16.0 psia). Exceeding this limit may damage the pump or cause leakage. Install pressure relief or monitoring if the system can exceed this value.

Operating Instructions, Chapter 3.3, Pg. 8
Process Limits
Minimum inlet pressure 5 kPa abs. without cavitation protection

Operating below 5 kPa abs. without cavitation protection can lead to cavitation damage. If lower pressures are required, ensure cavitation protection is installed or consult the manufacturer.

Operating Instructions, Chapter 3.3, Pg. 8
Electrical
Use motor circuit breaker set to rating plate current

The motor circuit breaker must be set to the nominal current specified on the motor rating plate to provide correct overload protection. Verify the setting before commissioning.

Operating Instructions, Chapter 6.2, Pg. 13
Maintenance
Install start-up screen for first 100 operating hours

A start-up screen in the inlet pipe prevents installation residues from entering the pump during the initial operating period. Remove or clean the screen after 100 hours to avoid flow restriction.

Operating Instructions, Chapter 6.3.3, Pg. 15
Process Limits
Set operating-liquid flow to 0.65 l/min

For operation with operating-liquid feed, adjust the flow rate to the nominal 0.65 l/min using a flow meter or graduated vessel. Incorrect flow can affect vacuum performance and cause cavitation or overheating.

Operating Instructions, Chapter 7.3, Pg. 18

Selection & Integration Q&A

When should I choose the 2BV3151?

Choose the 2BV3151 for vacuum duty with an ultimate pressure of 33 mbar abs. and G3/8 ports.

What are the requirements for connecting the 2BV3151 to a vacuum system?

Use G3/8 mating fittings for inlet and discharge, tightened to 16 Nm ±10%. Install a check valve if connecting to a vacuum accumulator to prevent liquid ingress. For the first 100 hours, install a start-up screen in the inlet pipe.

What maintenance items are required and what is not included in the base delivery?

The base delivery does not include a start-up screen, check valve, or operating-liquid flow meter; these must be procured separately. Regular maintenance includes checking operating-liquid flow and condition, and inspecting the start-up screen for the first 100 hours.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Technical Data Sheet — 2BV3151 vacuum pump (EN)
Datasheet ·181,9 КБ ·2 pp.
View PDF
PDF
Operating Instructions — (EN)
Manual ·2,5 МБ ·32 pp.
View PDF