Agilent Technologies IDP-4
Agilent Technologies ·Made in USA · In Active Production

Agilent Technologies IDP-4

Agilent Technologies IDP-4 — Vacuum technologies with Motor power 0.119 kW, Pumping speed 3.6 m³/h, Ultimate pressure 2.4 mbar.

The IDP-4 is an air-cooled dry scroll vacuum pump driven by a 0.16 HP (0.12 kW) single-phase motor, available for 100–127 VAC or 200–240 VAC 50/60 Hz service. It delivers 65 L/min peak pumping speed and an ultimate pressure of 1.8 × 10⁻¹ Torr at the default 3300 rpm, with speed adjustable from 2200 to 3300 rpm via serial interface. It serves as a clean, oil-free backing or roughing stage for analytical instruments and laboratory vacuum systems.

Motor power
0.119 kW
Pumping speed
3.6 m³/h
Ultimate pressure
2.4 mbar

Agilent Technologies Idp Pumps Series — Model Comparison & Selection

Model Motor power, kWUltimate pressure, mbarPumping speed, m³/hBase pressure, mbarSupply frequency, HzOperating temperature, °C
IDP-4 Current 0.1192.43.63.3—5
20.60 CFM 0.1193.33.63.350—
26.48 CFM 0.1193.33.63.350—
6.0 CFM ——————
Scroll Pumps for Helium Recirculation & Cryogenic Applications 0.119—3.63.3——

Full specifications

Core Performance & Functional Specifications
Motor power 0.16 HP
Pumping speed 60 L/min
Ultimate pressure 1.8 Torr
Base Pressure 3.3 mbar
Coverslip type No corrosive, explosive or particulate forming gases
Operating Speed 3300 % rpm
Leak rate 1 helium
Peak pumping speed mfr 65 L/min
Maximum recommended continuous inlet pressure mfr 1.0 atmosphere
Maximum outlet pressure mfr 0.45 bar
Gas ballast mfr 1 Thread
Motor protection mfr Thermal protection/over current protection/fuse
Installation mfr 1
Emissions and Immunity mfr 2014
Safety mfr 2006
IDP-10 mfr 3810
IDP-10 with inlet isolation valve mfr 3810
IDP-7/10 tip seal replacement kit mfr 3807
Exhaust silencer kit mfr 110
Purge kit mfr 3807
Gas ballast kit mfr 3807
Inlet trap mfr 25
Vibration isolation kit mfr 110 VIBISOKIT
IDP-35 mfr 3835
IDP-35 with Gauge mfr 3835
IDP-35 with Inlet Valve mfr 3835
IDP-35 with Inlet Valve and Gauge mfr 3835
Inlet HEPA filter, NW40 mfr 40
HEPA filter, NW25 mfr 25
IDP-45 mfr 3845
IDP-45 with Gauge mfr 3845
IDP-45 with Inlet Valve mfr 3845
IDP-45 with Inlet Valve and Gauge mfr 3845
IDP-15 mfr 3815
IDP-15 with inlet isolation valve mfr 3815
IDP-15 tip seal replacement kit mfr 3815
IDP-3 mfr Vibration isolation kit kit
IDP-4 mfr Replacement filter element element
IDP-7 mfr Vibration isolation kit kit
inlet valve closing time mfr 20 milliseconds
inlet valve opening time after power restore mfr 10 seconds
tip seal replacement duration mfr half an hour hour
IDP-4 maintenance duration mfr 15...30 minutes
integrated Pirani gauge pressure range mfr -4...1000 mbar
VPI valve isolation time mfr 20 ms
Maximum outlet pressure*** mfr 0.45 bar
Description of the IDP-4 Dry Scroll Pump mfr 188
Technical Specifications mfr 189
IDP-4 Dry Scroll Pump Outline Drawing mfr 191
Performance Curves mfr 193
Electrical Connections mfr 195
Grounding Instructions mfr 195
Mechanical Connections mfr 197
Gas Ballast mfr 199
Accessories and Spare Parts mfr 201
Optional Accessories mfr 201
Optional Inlet Valve Kit mfr 202
Cleaning and Preventive Maintenance mfr 205
External cleaning mfr 205
Internal cleaning as part of a Preventive Maintenance plan mfr 206
Verifying Performance mfr 206
Tip Seal Replacement mfr 207
Tip Seal Replacement Instructions mfr 208
User Maintenance and Repair mfr 216
Factory-Only Service mfr 217
Service Options mfr 218
Troubleshooting mfr 219
Window Description mfr 223
Europe mfr 10 m
Denmark mfr 10 m
Switzerland mfr 10 m
UK/Ireland mfr 13 m
India mfr 10 m
Israel mfr 10 m
Japan mfr 12 m
North America mfr 13 m
Body mfr Aluminum Aluminum
Seal mfr Viton Viton
Closing time (after solenoid valve power loss) mfr 25 ms
Closing burst mfr 0.01 liter
IDP3GBKIT mfr Breather Vent and Adapter Adapter
VPI16IDP24DC mfr -24
EXSLRIDP3 mfr Exhaust Silencer Kit Kit
X3802-68001 mfr Serial communication cable kit kit
Clearance on all sides mfr 20 cm
Lifting device threshold mfr 20 kg
Gas ballast duration mfr 30 hours
Dimensions, Weight & Mechanical Design
Weight 7.7 kg
Electrical, Power & Drive Specifications
Operating voltage mfr 100 VAC
Maximum inlet pressure at nominal voltage mfr 1.0 atmosphere
Operating voltages mfr 200 VAC
Fuse type mfr 5 mm
IDP-35/IDP-45 supply frequency mfr 50 Hz
Interfaces, Connections & Control
Inlet connection 16
Interface dimensions mfr 237 mm
Serial Connector & Pin allocation mfr 221
Pump Serial Connector mfr 221
Serial communication settings mfr 222
Window Description and Protocol mfr 223
Windows Protocol mfr 226
Operating Conditions, Environment & Protection
Cooling System Air-cooled
Operating temperature 5 °C
Storage temperature 20 °C
Ambient Relative Humidity mfr 5 condensing
Sound Pressure Levels mfr 50...55 dba
Altitude mfr 2000 m
Relative humidity mfr 5...95
Standards, Safety & General Data
Ultimate Pressure* (ISO 21360-1: 2020) (ISO 21360-2: 2020) mfr 1.8 rpm
Motor rating: EN 60034-1-2:2007 EN 60034-30 (GB 18613-2020) mfr 0.16 HP
Sound Pressure Levels (EN ISO 2151:2008) (ISO 4871:1996) (ISO 11201:2010) mfr 50...55 configuration

Description

Construction and series positioning

Performance behavior

Installation, control and operation

Integration & Operating Notes

Electrical
Select power cord and branch protection by voltage class

The IDP-4 is offered in 100–127 VAC and 200–240 VAC single-phase variants. The power cord must be rated at least 15 A for 100–127 V service and at least 10 A for 200–240 V service; undersized cords cause voltage drop and overheating. Mains fluctuation must remain within ±10% of nominal.

User Manual, Technical Specifications page 189; Preparation for Installation page 175
Process Limits
Keep exhaust backpressure below 6.5 psig to avoid shutdown

Maximum outlet pressure is 0.45 bar (6.5 psig). The pump automatically shuts off if discharge pressure exceeds this limit or if head temperature rises due to excessive exhaust back pressure. Size exhaust lines, mufflers and silencers so they do not restrict flow.

User Manual, Technical Specifications page 189; Mechanical Connections page 198
Process Limits
Gas ballast kit required for water vapor or solvent loads

The standard pump ships with the gas ballast port sealed. For water vapor or solvent applications, install the IDP3GBKIT; water handling is 4 g/hr typical and up to 10 g/hr in higher pressure ranges. Do not exceed 25 in-lb torque when installing the gas ballast adapter into the manifold.

User Manual, Gas Ballast page 199
Control & I/O
Serial link defaults to 9600 bit/s and 30 m maximum cable

Configure the host serial port to match WIN#108 (default 4 = 9600 bit/s; options 4800/9600/19200/38400). Remote I/O or serial cables must not exceed 30 m; longer runs compromise EMC and communication reliability. Use shielded, properly grounded cable.

User Manual, Window Description and Protocol page 223; Electrical Connections page 196
Maintenance
Replace fuse only with 5 A slow-blow 250 V 5×20 mm

The motor protection circuit uses a 5 A slow-blow 250 V 5×20 mm fuse. Replace only with an identical type and rating to maintain protection. Persistent fuse blowing or overcurrent stops should be diagnosed via error code WIN#206 before replacement.

User Manual, Technical Specifications page 190; Troubleshooting page 220
Cooling & Media
Stop the pump if surface temperature exceeds 65 °C

Pump surface temperature in excess of 65 °C (150 °F) is potentially damaging. Turn off and allow to cool if observed. Ensure cooling vents are not blocked and ambient temperature stays within 5–40 °C at 5–95% RH non-condensing.

User Manual, Startup Procedure page 181; Environmental Conditions page 184

Selection & Integration Q&A

When should I choose the IDP-4 over the IDP-3 or the larger IDP-7/IDP-10 in the same series?

Choose the IDP-4 when you need 65 L/min peak speed and 1.8 × 10⁻¹ Torr ultimate pressure from a 0.16 HP AC-powered pump with IDP-3-compatible mounting. The IDP-3 is 24 VDC and smaller; the IDP-7/IDP-10 offer higher speed for larger chambers. The IDP-4 fits analytical backing duty where AC mains are available.

What are the requirements for the inlet and exhaust plumbing and the electrical supply feeding the IDP-4?

Use clean NW16 or larger inlet and exhaust hardware with short lines and bellows for vibration isolation; exhaust must be unrestricted to stay below 0.45 bar (6.5 psig). Supply single-phase 100–127 VAC or 200–240 VAC 50/60 Hz within ±10%, with a cord rated 15 A (100–127 V) or 10 A (200–240 V).

What mounting clearances and ambient conditions does the IDP-4 require, and what happens if exhaust backpressure rises?

Allow at least 20 cm free space on all sides for ventilation and service access; operate at 5–40 °C, 5–95% RH non-condensing, up to 2000 m altitude. If discharge pressure exceeds 0.45 bar (6.5 psig) or head temperature rises from restricted exhaust, the pump automatically shuts off to protect itself.

What maintenance items and accessories are not included in the base IDP-4 delivery, and how are faults diagnosed?

The base pump ships with the gas ballast port sealed; the IDP3GBKIT, VPI inlet valve, exhaust silencer and serial communication cable kit are optional accessories. The 5 A slow-blow 250 V 5×20 mm fuse is a service item. Faults are read via serial WIN#205 status and WIN#206 error bitfield (locked rotor, bus overvoltage, Hall error, motor/heatsink overtemperature, system fault).

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Agilent IDP-4 Dry Scroll Vacuum Pump
Brochure ·10,7 МБ ·11 pp.
View PDF
PDF
IDP-4 Dry Scroll Pump User Manual
Manual ·231 pp.
View PDF