Nabertherm LHT 02/17
Nabertherm LHT 02/17 — High-temperature furnaces.
The LHT 02/17 is a 2-litre high-temperature chamber furnace with MoSi₂ heating elements, rated to 1750 °C from a 1-phase supply. Its 130 × 145 × 130 mm chamber and 46-minute heating time distinguish it as the smallest non-D variant in the LHT 17 series, suited to laboratory sintering, annealing and melting of small samples.
Nabertherm LHT Series — Model Comparison & Selection
Full specifications
| Chamber volume | 2 l |
| Electrical connection | 1-phase |
| Connected mfr | 3.40 |
| Heating time mfr | 46 min |
| Inner dimensions (W × D × H) mfr | 130 × 145 × 130 mm |
| Outer dimensions (W × D × H) mfr | 430 × 450 mm |
| Weight | 33 kg |
| Max temperature | 1750 °C |
Description
Construction and series positioning
- The LHT 02/17 is the 2-litre member of the LHT ../17 series; siblings include the 1-litre LHT 01/17 D, 3-litre LHT 03/17 D, 4-litre LHT 04/17 and 8-litre LHT 08/17.
- Unlike the D-suffixed 01 and 03 models, this unit is a non-D configuration; the D designation is not defined in the supplied facts, so no functional difference is asserted here.
- Chamber dimensions are 130 × 145 × 130 mm (W × D × H); outer dimensions are 430 × 450 mm with height not stated. Unit weight is 33 kg.
- Heating is by MoSi₂ elements, which permit a 1750 °C maximum working temperature.
Thermal behaviour
- The factory-listed heating time is 46 min; the corresponding start and end temperatures are not stated, so this value should be treated as a comparative indicator rather than a guaranteed ramp rate.
- No digitized curve points were supplied, so no load-dependent or atmosphere-dependent behaviour can be quantified.
Electrical and control
- The furnace connects to a 1-phase supply; the extra-spec entry 'Connected 3.40' carries no unit and is therefore not interpreted as a power rating.
- Controller and process-data functions are covered only by the general Nabertherm controller digest (series 500 and MyNabertherm app), which does not name this model; controller fitment must be confirmed at order.
Documentation scope
- The attached digests cover controllers, fiber-optics glass, foundry and dental product lines; none contains model-specific installation or operating instructions for the LHT 02/17.
Integration & Operating Notes
The MoSi₂ heating elements and chamber insulation are rated to a 1750 °C maximum. Any process setpoint above this risks element and insulation degradation; verify the actual sample or crucible temperature, not only the controller setpoint, before running.
The unit is specified for 1-phase connection. The supplied 'Connected 3.40' value has no unit and cannot be used for breaker or cable sizing; obtain the nameplate current and voltage from the factory before preparing the electrical installation.
The controller digest describes series 500 functions and the MyNabertherm app but does not list the LHT 02/17. Confirm which controller, program storage and interface options are included before designing data logging or furnace integration.
Selection & Integration Q&A
Pick the 02/17 when a 2-litre chamber (130 × 145 × 130 mm) at up to 1750 °C is enough and the D configuration is not required. Step up to the 04/17 or 08/17 for larger batches; the 01/17 D and 03/17 D are the D-suffixed alternatives at 1 and 3 litres.
A 1-phase supply is required, but the supplied 'Connected 3.40' value has no unit, so cable and breaker sizing must come from the nameplate. Controller fitment is not fixed by the model code; confirm the series 500 configuration and any interface options at order.
The supplied facts list only the furnace itself; no controller model, thermocouple, crucible, exhaust accessory or interface cable is confirmed as included. The controller digest covers series 500 and the MyNabertherm app generically, so accessories and spares must be specified explicitly on the order.