Nabertherm LHT 08/18
Nabertherm LHT 08/18 — High-temperature furnaces.
The LHT 08/18 is a 3-phase, 8-litre high-temperature chamber furnace with MoSi₂ heating elements reaching 1800 °C, positioned as the largest chamber in the LHT 17/18 series above the 1–4 litre siblings. Its 200 × 200 × 200 mm workspace and 60-minute heating time suit laboratory sintering, annealing and melting of small ceramic or metallic loads requiring the series' top temperature class.
Nabertherm LHT Series — Model Comparison & Selection
Full specifications
| Chamber volume | 8 l |
| Electrical connection | 3-phase4 |
| Connected mfr | 6.70 |
| Heating time mfr | 60 min |
| Inner dimensions (W × D × H) mfr | 200 × 200 × 200 mm |
| Outer dimensions (W × D × H) mfr | 500 × 500 mm |
| Weight | 47 kg |
| Max temperature | 1800 °C |
Description
Construction and series positioning
- Chamber volume 8 l in a cubic 200 × 200 × 200 mm workspace; outer dimensions 500 × 500 mm (height not stated in the verified facts).
- MoSi₂ heating elements define the 1800 °C maximum temperature class; the model is the largest chamber among the listed siblings (LHT 01/17 D, LHT 02/17, LHT 03/17 D, LHT 04/17), which sit at 1–4 l and the 1700 °C class.
- Unit weight 47 kg; electrical connection is 3-phase (4-wire designation as printed).
Thermal behaviour
- Maximum working temperature 1800 °C; the factory heating-time figure is 60 min (no start/end temperatures are given in the verified facts, so the ramp cannot be reconstructed).
- No digitized curve points were supplied, so load-dependent uniformity and cool-down behaviour cannot be quantified from the available data.
Control and operation
- The attached controller documentation covers the Nabertherm 500-series controllers and the MyNabertherm app, including process-data storage and AMS2750F instrumentation types; it does not print model-specific wiring for the LHT 08/18.
- No model-specific installation, connection or operating instructions were found in the supplied document digests; the remaining digests cover unrelated product lines (heating cabinets, foundry, dental) and are not applicable to this furnace.
Integration & Operating Notes
The verified electrical connection is stated only as '3-phase4'. Before ordering, confirm the plant's phase/neutral/ground arrangement and the actual connected load with the factory, because the 'Connected' value of 6.70 is printed without a unit and cannot be used for cable or breaker sizing as supplied.
The 1800 °C maximum is the MoSi₂ element temperature class of this modification; operating above it degrades the heating elements and invalidates the furnace's thermal design. The 60-minute heating time is a factory figure without stated endpoints, so program ramp rates from application trials rather than assuming it applies to every load.
Selection & Integration Q&A
Pick the LHT 08/18 when you need the 8-litre, 200 × 200 × 200 mm chamber and the 1800 °C MoSi₂ class. The siblings are 1–4 litre, 1700 °C units; choose them for smaller loads where the higher temperature ceiling is not required.
A 3-phase supply matching the '3-phase4' connection is required. The connected-load figure of 6.70 is printed without a unit, so cable, breaker and controller sizing must be confirmed with Nabertherm; controller/recorder options are covered in the 500-series documentation.
The supplied documents contain no LHT 08/18 maintenance schedule or error-code list, and no accessory list is given. Request the model-specific operating manual and a quotation for controller, recorder and thermocouple options from Nabertherm before ordering.