Agilent Technologies Smart SPME Fibers
Agilent Technologies ·Made in USA · In Active Production

Agilent Technologies Smart SPME Fibers

Agilent Technologies Smart SPME Fibers — Sample preparation.

Smart SPME Fibers are 23-gauge, 10 mm fiber assemblies with a 30 µm PDMS sorption phase (0.6 µL phase volume) for nonpolar semivolatile extraction. The Smart designation adds an integrated memory chip that carries method parameters to the autosampler, distinguishing this modification from non-Smart SPME fibers in the same series. They are used as the extraction interface in GC/HPLC sample preparation workflows.

Agilent Technologies Solid Phase Microextraction Spme Series — Model Comparison & Selection

Model Arrow length, mmFiber length, mmPack quantity, pkPhase thickness, µmSorption phase volume, microliter
Smart SPME Fibers Current 20103300.6
Smart SPME Arrows | Solid Phase Microextraction 20103300.6
SPME Fibers 20103300.6

Full specifications

Core Performance & Functional Specifications
Pack Quantity 3 pack
Needle gauge mfr 23 gauge
Arrow outside diameter mfr 1.1 mm
SPME fiber needle gauge mfr 23 gauge
SPME Arrow outside diameter mfr 1.1 mm
SPME Arrow inner core diameter mfr 0.4 mm
Dimensions, Weight & Mechanical Design
Arrow Length 20 mm
Fiber Length 10 mm
Electrical, Power & Drive Specifications
Phase Thickness 30 µm
Sorption Phase Volume 0.6 µL

Description

Construction and series positioning

Phase and application behavior

Installation and operation

Integration & Operating Notes

Mounting
Match holder and injector to 23-gauge, 10 mm fiber geometry

The 23-gauge needle and 10 mm fiber length are the interface dimensions of this model. Do not substitute Arrow-format hardware (20 mm arrow, 1.1 mm OD), which belongs to the SPME Arrow sibling and will not seat correctly with this fiber.

te solid phase microextraction fundamentals spme arrow 5994 5775en agilent
Control & I/O
Smart chip carries method data; confirm reader compatibility

This is the Smart variant, so method information is stored with the fiber and read by the autosampler. Verify that the autosampler/controller in use supports Smart fiber reading; non-Smart SPME fibers in the series lack this capability.

te solid phase microextraction fundamentals spme arrow 5994 5775en agilent
Process Limits
30 µm PDMS phase is for nonpolar semivolatiles only

Phase selection is a process condition: the 30 µm PDMS film is documented for nonpolar semivolatiles. Polar volatiles require the 65 µm DVB/PDMS phase, a different fiber; using this fiber for that class of analytes is outside its documented scope.

te solid phase microextraction fundamentals spme arrow 5994 5775en agilent

Selection & Integration Q&A

When should I choose this Smart SPME Fiber rather than the SPME Arrow or a non-Smart fiber in the same series?

Choose this fiber for 10 mm, 23-gauge fiber-format extraction of nonpolar semivolatiles with method data carried on the fiber (Smart). Choose the SPME Arrow sibling when the 20 mm arrow geometry (1.1 or 1.5 mm OD) is required; choose a non-Smart fiber only where Smart reading is not used.

What adjacent system parts must be compatible with this fiber?

The autosampler/injector must accept the 23-gauge, 10 mm fiber format, and the controller must support Smart fiber reading to use the stored method data. Arrow-format hardware (20 mm, 1.1 mm OD) is not compatible with this fiber and belongs to the separate SPME Arrow modification.

What mounting and phase-selection limits apply to this model?

Mount it in fiber-format (23-gauge, 10 mm) hardware only; the 20 mm arrow length and 1.1 mm arrow OD are not this model's dimensions. The 30 µm PDMS phase is documented for nonpolar semivolatiles; polar volatiles call for the 65 µm DVB/PDMS fiber instead.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Solid Phase Microextraction (SPME) Fibers and Arrows
Brochure ·994,0 КБ ·9 pp.
View PDF