BINDER MKFT 720
BINDER MKFT 720 — Climate chambers with Temperature -70…180 °C.
The MKFT 720 is a 734 L deep-temperature alternating climate chamber with a -70…180 °C range and 10…98 %RH humidity control, powered by an 11 kW 400 V 3 N/PE 50 Hz supply. It is the largest MKFT variant, distinguished from the MKFT 115/240 by its 734 L interior and 40 kg per-rack load capacity, and is intended for dynamic temperature-humidity cycling of large test loads in qualification and reliability testing.
BINDER MKFT Series — Model Comparison & Selection
Full specifications
| Temperature | -70...180 °C |
| Interior volume | 734 L (MKFT720-400V) |
| Load per rack | 40 kg (MKFT720-400V) |
| Maximum heat compensation | 800 W |
| Nominal power | 11 kW (MKFT720-400V) |
| Article Number mfr | 9020 |
| Power frequency | 50 Hz (MKFT720-400V) |
| Rated voltage | 400 V |
| Unit fuse | 32.0 A (MKFT720-400V) |
| Humidity range | 10...98 % RH |
| Cooling down time from 180°C to -70°C mfr | 120 min |
| Humidity fluctuation with humidity dependent on set value mfr | 2.5 % r.F. |
| Average heating-up rate according to IEC 60068-3-5 between -40°C and 180°C mfr | 4.8 K/min |
Description
Construction and series positioning
- The MKFT 720 is a floor-standing alternating climate chamber with 734 L usable interior volume and a deep-temperature refrigeration system reaching -70 °C.
- Within the MKFT series, it is the largest model; the MKFT 115 and MKFT 240 share the same -70…180 °C range but offer smaller interiors. The MKFT 720 is the only MKFT size listed with a 40 kg per-rack load rating and an 800 W maximum heat compensation.
- The standard variant is MKFT720-400V (Art. No. 9020-0384) for 400 V 3 N/PE 50 Hz; the -C variant (MKFT720-480V-C, Art. No. 9020-0360) adds a voltage and frequency changer for 480 V 3~ 60 Hz supplies.
Thermal and humidity behavior
- Temperature uniformity is 0.3…2.0 K and fluctuation 0.1…0.5 K, both dependent on set value. With humidity active, the temperature range narrows to 10…95 °C and fluctuation increases to 0.1…1 K; humidity fluctuation is 2.5 %r.F.
- Average heating rate per IEC 60068-3-5 is 4.8 K/min between -40 °C and 180 °C; average cooling rate is 4.0 K/min between 180 °C and -40 °C. A full cool-down from 180 °C to -70 °C takes 120 min.
- The 800 W heat compensation allows dissipative test specimens to be conditioned without exceeding the chamber's control capability.
Installation, control and operation
- The chamber requires a 400 V 3 N/PE 50 Hz supply with a 32.0 A unit fuse and 11 kW nominal power. From size 115 upward, a rear power switch is provided in addition to the main power switch; both must be on for commissioning and troubleshooting.
- Water connections are required for humidity control: freshwater supply (automatic via water pipe or manual via internal freshwater can from size 115 on) and wastewater drain. The water cooling option, available for MKFT 720, adds cooling water inlet/outlet connections.
- The MB2 chamber controller supports fixed-value, timer, time-program and week-program modes, with a chart-recorder display, event list, user management and Ethernet/serial interfaces. Temperature safety devices include an over-temperature protective device (class 1) and a safety controller (class 2).
- Defrosting during refrigerating operation and anti-condensation protection are handled automatically by the controller.
Integration & Operating Notes
The 11 kW nominal power and 32.0 A unit fuse require a dedicated three-phase supply with neutral and protective earth. Verify the building distribution can deliver the run-up current without nuisance tripping; the -C variant is needed for 480 V 60 Hz sites.
The humidity sensor must not be exposed to ammonia above 20 ppm (14 mg/m³) workplace threshold or 5500 ppm (4000 mg/m³) permanent load, nor ozone above 0.1 ppm (0.2 mg/m³) or 0.5 ppm (1 mg/m³) permanent. Verify process atmospheres before introducing test specimens that outgas these substances.
From size 115 upward, the chamber has a rear power switch in addition to the main power switch. During commissioning or after troubleshooting, confirm both switches are in the on position; otherwise the controller will not energize and no heating, cooling or humidity function will operate.
Schedule at least one maintenance per year, including a leak test per Regulation (EU) 517/2014 Article 4 and Article 10(1)(b). Document the leak test in the service log book. Steam humidifier maintenance is also required at least annually, with intervals depending on water quality and steam output.
After 8760 operating hours or two years, a service message appears on the controller. It can be confirmed but reappears every two weeks until reset by BINDER Service. Plan a service intervention at that mark to avoid repeated alarms and to perform the required maintenance.
With increased dust in ambient air, clean the condenser fan several times a year. Check the fan grid behind the left maintenance access flap every week and clean by suction after disconnecting the chamber from power. Condensers are recommended to be cleaned every 1 to 2 years by a qualified technician.
Replace the door gasket only after the chamber has cooled to ambient temperature. Attempting replacement while the chamber is warm can deform or damage the new gasket and compromise the seal, leading to humidity and temperature control errors.
Selection & Integration Q&A
Choose the MKFT 720 when you need the largest interior (734 L) and a 40 kg per-rack load with up to 800 W heat compensation. The MKFT 115 and 240 share the -70…180 °C range but have smaller volumes and lower load ratings; select them for smaller specimens or when floor space is limited.
Humidity control requires a freshwater supply (automatic via water pipe or manual via internal freshwater can from size 115 on) and a wastewater drain. If the water cooling option is ordered, cooling water inlet and outlet must also be plumbed. Without these, only temperature operation is possible.
The base delivery does not include the recommended disinfectant spray (Art. No. 1002-0022), replacement door gaskets, or the BINDER Pure Aqua Service. Annual maintenance, leak test, humidifier service and condenser cleaning are scheduled service actions; the 8760-hour service message requires BINDER Service reset.