Peter Huber Kältemaschinenbau Ministat 230w Kompakter Kälte-Badumwälzthermostat
Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Ministat 230w Kompakter Kälte-Badumwälzthermostat

Peter Huber Kältemaschinenbau Ministat 230w Kompakter Kälte-Badumwälzthermostat — Thermostatic baths.

The Ministat 230w is a water-cooled refrigerated/heating bath circulator with a 3.5 l bath and a variable-speed pressure/suction pump, covering -40 to 200 °C with ±0.02 K stability. Its water-cooled condenser and G1/2 cooling-water connection distinguish it from air-cooled siblings in the Ministat series. It serves as a precise temperature source for external circuits and bath immersion in laboratory and industrial processes.

Direct drop-in replacements

Eppendorf
MixMate ®
47%
match
⚖️ Compare

Peter Huber Kältemaschinenbau Ministat Series — Model Comparison & Selection

Model Max delivery flow rate, liter/minutePower supplyTemperature range, °CWeight, kgAmbient temperature limit, °CController
Ministat 230w Kompakter Kälte-Badumwälzthermostat Current 16208-240V 1~/2~ 50/60Hz-40–200365–40Pilot ONE
Ministat 125w Kompakter Kälte-Badumwälzthermostat 22110-120V 1~ 60Hz-25–150265–40Pilot ONE
Ministat 240w Kompakter Kälte-Badumwälzthermostat 22220-240V 1~/2~ 50/60Hz-45–200415–40Pilot ONE

Full specifications

Core Performance & Functional Specifications
Filling volume 3 l (min.)
Maximum delivery flow rate 22 l/min (pressure pump; 0, 7 bar)
suction pump; 0, 4 bar: 16 l/min
Pump connection M16x1 AG male
Pump speed adjustable Yes
Pump type Pressure and suction pump, variable speed
Refrigerator water-cooled, natural refrigerant
External sensor connection Pt100
Temperature range -40...200 °C
Temperature stability mfr ±0, 02 K
Dimensions (W x D x H) mfr 255 x 450 x 476 mm
Heating capacity mfr 1, 6 - 2, 1 kW
Bath opening WxD/BD mfr 170 x 85 / 135 mm
Dimensions, Weight & Mechanical Design
Weight 36 kg
Electrical, Power & Drive Specifications
Current consumption 11 A (max.)
Fuse rating 16 A
Power supply 208-240V 1~/2~ 50/60Hz
Interfaces, Connections & Control
Controller Pilot ONE
Digital interface Ethernet, USB (Host u. Device), RS232
Materials, Media & Process Compatibility
Refrigerant R-290 (A3, H220) (1st stage)
Maximum viscosity 50 mm²/s
Refrigerant quantity 1st stage mfr 0, 06 kg (1st stage)
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Cooling water connection G1/2 male
Cooling water differential pressure 2 bar (min.)
Cooling Water Pressure 6 bar (max.)
Protection rating IP20
Cooling capacity mfr 100 0, 42; 20 0, 42; 0 0, 38; -10 0, 33; -20 0,
Cooling water consumption at 15°C, outlet 0 °C mfr 20, 4 l/h (at 15°C, outlet 0 °C)
Standards, Safety & General Data
Safety class III / FL

Description

Construction and series positioning

Thermal behavior and media

Installation, control and operation

Integration & Operating Notes

Cooling & Media
Cooling water pressure must stay within 2–6 bar differential

Facility water supply must provide at least 2 bar differential pressure to actuate the water-cooled condenser, but must never exceed 6 bar static pressure or the cooling circuit can be damaged. Verify pressure at the G1/2 male connections before commissioning.

Ministat 230w Immersion Circulator Datasheet, page 2
Cooling & Media
Cooling water intake limited to 5–20 °C

Water below 5 °C or above 20 °C degrades cooling performance and may cause condensation on uninsulated pipes. If the water can fall below the dew point, insulate all cooling-water piping to prevent corrosion and dripping.

Ministat 230w Immersion Circulator Datasheet, page 2
Electrical
Voltage and frequency tolerances are interdependent

The supply may deviate ±5% in voltage only when frequency deviation is simultaneously within ±2%; the combination of -5% voltage with +2% frequency is explicitly not allowed. Check the site supply against this rule before connecting the 208–240 V unit.

Ministat 230w Immersion Circulator Datasheet, page 2
Electrical
Country-specific plug must be ordered with the unit

Single/two-phase devices are delivered with a power cable and a country-specific plug that must be specified at the time of ordering. Confirm the plug type for the destination country to avoid a non-usable power connection on delivery.

Ministat 230w Immersion Circulator Datasheet, page 2
Process Limits
Cooling capacity at -40 °C is only 0.05 kW

Heat load from samples or external circuits must remain below the available cooling capacity at the setpoint. At -40 °C only 0.05 kW is available, so large or warm loads will prevent the bath from reaching or holding the low-end setpoint.

Ministat 230w Immersion Circulator Datasheet, page 1
Process Limits
Bath fluid viscosity must not exceed 50 mm²/s

Highly viscous fluids overload the pump and reduce circulation. Select bath fluid with a kinematic viscosity at the lowest operating temperature below 50 mm²/s, especially when running near -40 °C where many fluids thicken significantly.

Ministat 230w Immersion Circulator Datasheet, page 1
Mounting
Install indoors at 5–40 °C ambient

The installation room must remain between 5 °C and 40 °C. Operation outside this range degrades cooling performance and may trip protection. The IP20 enclosure also requires a dry, dust-controlled indoor location.

Ministat 230w Immersion Circulator Datasheet, page 2
Mounting
Class A Group 1 EMC classification for industrial areas

The unit is classified EN55011 Class A Group 1, intended for industrial electromagnetic environments. In residential or sensitive EMC areas, additional filtering or physical separation from sensitive equipment may be required.

Ministat 230w Immersion Circulator Datasheet, page 2
Maintenance
Use only cooling water compatible with circuit materials

The cooling water circuit contains copper, stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM. Aggressive or incompatible water will corrode or degrade these materials and cause leaks; verify water quality before connecting the facility supply.

Ministat 230w Immersion Circulator Datasheet, page 2

Selection & Integration Q&A

When should I choose the Ministat 230w over the air-cooled Ministat 230 or the smaller 125w/240w models?

Choose the 230w when facility cooling water is available and heat rejection to room air is undesirable; it shares the 3.5 l bath and -40…200 °C range with the air-cooled 230. The 125w offers a smaller bath, while the 240w provides greater cooling capacity for higher heat loads.

What are the requirements for the external circuit connected to the Ministat 230w pump?

The variable-speed pressure/suction pump delivers up to 22 l/min at 0.7 bar and suctions 16 l/min at 0.4 bar. Size external tubing and heat exchangers so pressure drop stays within these limits, and keep fluid viscosity below 50 mm²/s to avoid overloading the pump.

What installation environment and duty limits apply to the Ministat 230w?

Install indoors at 5–40 °C ambient with IP20 protection. Cooling water must be 5–20 °C at 2–6 bar differential pressure. The unit is EN55011 Class A Group 1 for industrial EMC environments; residential use may require additional filtering.

What maintenance and accessories are required beyond the base delivery?

The base unit includes a power cable with country-specific plug only if specified at order. Bath fluid, external Pt100 sensor, and displacement rack are not included. Cooling-water hoses and fittings for the G1/2 male connections must be supplied separately; no periodic maintenance schedule is given in the datasheet.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Ministat 230w Immersion Circulator Datasheet
Datasheet ·93,4 КБ ·2 pp.
View PDF