Elmo Rietschle 2BV5131
Elmo Rietschle 2BV5131 — Liquid Ring Vacuum Pumps with Motor power 15 kW, Pumping speed 15 m³/h.
The 2BV5131 is a single-stage liquid-ring vacuum pump/compressor in the L-BV5 series, driven by a 15.0 kW motor and delivering 15.0 m³/h at 50 Hz or 17.4 m³/h at 60 Hz. It is the mid-range 15 kW modification, positioned between the 11 kW 2BV5121 and the high-capacity 2BV5161, and is intended for continuous vacuum or pressure duty where a robust liquid-ring principle is required.
Elmo Rietschle L-BV5 Series — Model Comparison & Selection
| Model | Motor power, kW | Operating principle | Noise level, dB | Power supply | Pumping speed, m³/h | Weight, kg |
|---|---|---|---|---|---|---|
| 2BV5131 Current | 15 | Liquid ring | 74 | AC | 17.4 | 178 |
| 2BV5110 | 5.5 | ring blow | 67 | AC | — | 67 |
| 2BV5111 | 7.5 | Liquid ring | 72 | 3~ AC | — | 124 |
| 2BV5121 | 11 | Liquid ring compressor | 70 | AC | 40 | — |
| 2BV5161 | 15 | Liquid ring | 74 | AC | 500 | 160 |
| L-BV5 2060 | — | — | — | — | — | — |
Full specifications
| Motor power | 15.0 kW |
| Operating principle | Liquid ring |
| Pumping speed | 15.0 m³/h (50 Hz) 60 Hz: 17.4 m³/h |
| Number of stages | 1 dimensionless |
| Weight | 178 kg |
| Weight (alt var) mfr | 182 kg |
| Power supply | AC |
| Inlet flange | 190-210 |
| Outlet flange | 190-210 |
| Noise level | 74 dB(A) |
| Operating temperature | 20 °C |
| Protection rating | IP55 |
| Sound pressure level (alt var) mfr | 75 dB(A) |
Description
Construction and series positioning
- Single-stage liquid-ring machine with a 15.0 kW AC motor, IP55 protection, and a weight of 178 kg (182 kg for the alternative variant).
- Within the L-BV5 series, the 2BV5131 shares the 15 kW motor rating with the larger 2BV5161 but delivers a much lower pumping speed (15.0 m³/h at 50 Hz / 17.4 m³/h at 60 Hz), making it suitable for lower-flow, higher-pressure-ratio duties.
- Compared to the 11 kW 2BV5121 (45.0 m³/h), the 2BV5131 offers higher motor power but lower flow, indicating a different impeller/porting design optimized for pressure or vacuum level rather than raw capacity.
- Available in cast iron (K) and stainless steel (H) material versions, with IE3 or NEMA (NP) motor efficiency, and ATEX category 2G versions (option F91) for explosive atmospheres.
Behavior under load and media
- The liquid-ring principle uses an operating liquid (typically water) to form a rotating ring; the maximum gas/vapour temperature is +80 °C, and the operating-liquid temperature range is +5 °C to +80 °C (nominal +15 °C).
- For gas temperatures above +80 °C, the operating-liquid flow must be increased to 2× the design flow (for 2BV5… types) or a pre-condenser must be installed.
- Maximum discharge pressure in vacuum operation is 1.3 bar abs for the 2BV5… series; maximum permissible internal pressure is 8 bar abs (6 bar abs for 2BV5410-.F).
- The first fill quantity of operating liquid for the 2BV5131 is 3.0 L.
- Maximum water carry-over through the inlet is 2.5× the design operating-liquid flow continuous and 5× for max 2 s (for 2BV51.. types).
- Minimum clearances for heat dissipation: 53 mm around the fan guard for the 2BV5131.
Installation, connection and operation
- Electrical supply tolerance: ±5% voltage and ±2% frequency deviation without loss of performance; motor insulation resistance must be checked (dry windings if ≤1 kΩ per volt).
- Piping connections to suction and discharge must not exceed 100 Nm tightening torque; an intake strainer should be fitted for the first 100 operating hours.
- Maximum installation altitude is 1000 m above sea level; consult service if exceeded.
- Maximum vibration velocity veff = 4.5 mm/s; measure at points shown in Fig. 7.
- For frequency-converter operation, the maximum speed for the 2BV5131 is 2066 min⁻¹ (range 1180–2066 min⁻¹); do not exceed this.
- ATEX versions require compulsory monitoring of operating-liquid feed and liquid level, pressure monitoring on the discharge side, and bleeder resistance < 10^6 Ohm; frequency-converter operation is not permitted for ATEX.
Integration & Operating Notes
Over-tightening the suction or discharge connections can damage the pump casing or threaded ports. Use a torque wrench and verify that the mating flange or fitting is aligned without stress. The maximum permissible vibration velocity is 4.5 mm/s; ensure rigid mounting and flexible connections where necessary.
If the gas or vapour temperature exceeds +80 °C, the operating-liquid flow must be increased to 2× the design flow for 2BV5… types, or a pre-condenser must be installed upstream. Additionally, the suction pressure must remain at least 50 mbar above the vapour pressure of the operating liquid to avoid cavitation; consult the manufacturer if this cannot be guaranteed.
Measure the insulation resistance of the motor windings. If the value is ≤1 kΩ per volt of measurement potential, the windings must be dried before start-up. Also ensure that the supply voltage and frequency stay within ±5% and ±2% respectively, and that the minimum air gap of 5.5 mm between non-insulated live parts and earth is maintained in the terminal box.
For ATEX versions, ball bearings must be serviced by a service technician every 2 years or 18,000 operating hours. Weekly dust removal from the unit is also required. Non-ATEX units have a bearing maintenance interval of 2.5 years or 20,000 operating hours. Use grease type UNIREX N3 or equivalent per DIN 51825-K3N, filling approximately 50% of the free space in the ball bearings.
Selection & Integration Q&A
Choose the 2BV5131 when you need a 15 kW motor but a lower flow (15.0 m³/h at 50 Hz, 17.4 m³/h at 60 Hz) than the 2BV5121 (45 m³/h at 11 kW). It suits applications requiring higher pressure ratios or vacuum levels at modest flow, and is available in ATEX version for hazardous areas.
The operating liquid (typically water) must be supplied at a temperature between +5 °C and +80 °C (nominal +15 °C) and at the design flow rate. For ATEX versions, the flow must be monitored and the unit must shut down if the flow drops to ≤50% of design. The liquid level must be kept within 140–185 mm (hf min/hf max for 2BV5131) and monitored independently.
For non-ATEX versions, a frequency converter may be used but the speed must not exceed 2066 min⁻¹ (range 1180–2066 min⁻¹). For ATEX versions, operation with a frequency converter is explicitly not permitted; the motor must be connected directly to the supply.