Induztr
Resumen técnico Visor de documentos Modelos relacionados

Operating Instructions — C-VLR 401 OXY vacuum pump (BA 886-OXY, ed. 1.0 12.10.2023, EN)

Technical Reference Summary

Covered Models & Document Scope

Cubre las bombas de vacío de anillo líquido sin contacto C-VLR 401, C-VLR 501 y C-VLR 651 en la variante OXY (pintadas en azul, para gases con contenido de oxígeno superior al 21% en volumen y otros agentes oxidantes gaseosos). Documento BA 886-OXY-EN, edición 1.0, 12.10.2023.

Section-by-Section Technical Breakdown

pp. 14-15
Descripción general del producto y funcionamiento

Describe el diseño de las bombas de vacío de pistón rotativo (garra) de doble eje C-VLR 401/501/651 OXY con rotores de garra secos sin contacto sincronizados por un par de engranajes lubricados con aceite. Enumera las posiciones de los componentes (conexión de vacío, silenciador de escape, purga de condensado, entrada/salida de aire de refrigeración, punto de llenado de aceite, mirilla de aceite, purga de aceite con imán, flecha de sentido de giro, superficies calientes >70 °C) y los campos de la placa de características.

  • Double-shaft rotary piston vacuum pump with contact-free, dry-running claw rotors
  • Gearbox and bearings oil-lubricated; gearbox separated from compression chamber by special seals
  • Inlet-side connection flange and pressure-side exhaust silencer; intake air cleaned by mesh filter
  • Integral non-return valve prevents ventilation of the evacuated system after stop
  • Cooling by drum fan drawing fresh air through cooling air inlet and discharging heated air at cooling air outlet
  • Driven via coupling by flanged three-phase standard motor
  • OXY pumps are blue painted to distinguish them from standard variants
  • Data plate includes model/size, serial number, year of construction, data matrix barcode, article number, speed 50/60 Hz, motor output 50/60 Hz, operating mode, pumping capacity 50/60 Hz, final pressure (abs.) 50/60 Hz
pp. 16
Campos de aplicación

Define el rango de funcionamiento admisible: funcionamiento continuo entre 700 mbar (abs.) y 200 mbar (abs.) de presión de entrada, evacuación de sistemas cerrados limitada al 2% de la capacidad de bombeo nominal, y capacidades de bombeo con aspiración libre a 50 Hz. Indica la reducción de prestaciones por encima de 1000 m de altitud y las restricciones sobre la frecuencia de conmutación y la temperatura ambiente/de entrada.

  • Suitable for air or other gases with oxygen content by volume above 21%
  • Continuous operation permitted at any pressure between 700 mbar (abs.) and 200 mbar (abs.) inlet pressure
  • Volume of closed systems to be evacuated must be no more than 2% of nominal pumping capacity
  • Free-intake pumping capacity at 50 Hz: 380 m³/h (VLR 401), 495 m³/h (VLR 501), 650 m³/h (VLR 651)
  • Pumping capacity vs. intake pressure per data sheet D 886-OXY
  • Frequent switching (approx. 10 times per hour) or high ambient/inlet temperatures may exceed motor winding and bearing temperature limits — contact manufacturer
  • Observe motor protection class on motor data plate; protect outdoor installation from environmental influences
pp. 17-20
Instalación

Cubre la preparación de la instalación, el montaje mecánico, la conexión de tuberías, la comprobación del aceite lubricante, la conexión eléctrica y la monitorización de presión. Especifica la ventilación para mantener el oxígeno en la sala ≤21% en volumen, el montaje horizontal con una inclinación máx. de 8°, las distancias mínimas, el límite de contrapresión, el tipo de aceite y los requisitos de protección eléctrica.

  • Sufficiently vent installation room; oxygen content by volume in room air may not exceed 21%
  • Machine freely accessible from all sides; do not close ventilation grids and holes
  • Provide at least 50 cm space around machine for maintenance
  • Operate only when set up horizontally; max. inclination 8° in all directions
  • Secure machine against tipping over and falling; floor must be plane and even
  • Cooling air inlets and outlets at least 30 cm from adjacent walls; cooling air must not be recirculated
  • Ambient temperature min. +5 °C, max. +40 °C
  • Maximum permissible back pressure +50 mbar; exhaust air opening must not be closed or restricted
  • Only screw in pipes by hand; use flexible connections/compensators if necessary
  • Use only oil type OXY-GEAR-LUBE 160
  • Electrical installation by qualified electrician per EN 60204; main switch and motor protection switch provided by user
  • Motor protection switch with overload-dependent turn-off delay recommended
  • Pressure monitoring system not included in scope of delivery; user must install it and switch off pump if minimum permissible pressure is undershot
pp. 21-23
Puesta en marcha y puesta fuera de servicio

Describe las comprobaciones de arranque, la verificación del sentido de giro, el funcionamiento incluyendo la descarga de condensado, y la puesta fuera de servicio/almacenamiento/puesta en servicio de nuevo. Enfatiza la pureza del aceite (solo OXY-GEAR-LUBE 160), el reinicio solo tras la parada y el secado de la bomba antes de la parada.

  • Installation check: no transport/assembly damage, safe horizontal standing, correct and leak-tight pipe connections, tight screw/flange connections, electrical installation per connection diagram, adequate ventilation, oil filled and level checked, pump and pipelines cleaned, optional accessories functional
  • Check rotation direction with phase sequence indicator (clockwise); brief start max. two seconds; when looking at motor blower it must rotate counter-clockwise
  • Keep a distance of 1 m to outlet and inlet connections during rotation check
  • Do not discharge condensate manually; allow machine to cool and wear protective gloves
  • Before shutdown >2 hours or decommissioning, run pump at 700 mbar (abs.) for at least 15–30 minutes with dry air to remove moisture and pollution
  • Restart only after machine has stopped completely
  • If lubricating oil may have been mixed with organic substances, replace immediately; if machine polluted with organic substances, put out of operation and clean by specialist personnel authorised by Elmo Rietschle
pp. 24-30
Mantenimiento y reparación

Cubre la seguridad operativa, la tabla de mantenimiento, la limpieza, el rellenado y cambio de aceite lubricante, el filtro de aire, el motor y el acoplamiento, la reparación/servicio y las piezas de repuesto. Especifica el tipo de aceite OXY-GEAR-LUBE 160 y hace referencia a la lista de piezas de repuesto E 886-OXY.

  • Only oil type OXY-GEAR-LUBE 160 permitted for lubrication
  • Check oil level through oil sight glass and top up if necessary
  • Air filter to be replaced when polluted (see Chapter 7.6)
  • Spare parts per spare parts list E 886-OXY
  • Repairs only by authorised workshops using original spare parts
pp. 31
Errores

Tabla de resolución de problemas (Tab. 4) que enumera fallos, causas y medidas de eliminación, con referencias a capítulos para la conexión eléctrica, conexión de tuberías, filtro de aire, uso previsto y limpieza. Advierte de no reiniciar nunca una bomba tras una parada automática sin determinar y subsanar la causa.

  • Never put pump back into operation after automatic shut-off without unequivocally finding out the reason and remedying it
  • Malfunctions covered: motor protection switch trip, insufficient suction capacity, final pressure not reached, machine overheating, strange noise
  • Contact Elmo Rietschle Service for other malfunctions or those that cannot be eliminated
pp. 33
Datos técnicos

El capítulo 10 contiene los datos técnicos; los valores detallados están en la hoja de datos D 886-OXY. El manual hace referencia al capítulo 10 para el peso, el nivel de presión sonora y otros datos.

  • Technical data and characteristic curves in data sheet D 886-OXY
  • Weight per chapter 10
  • Sound pressure level per chapter 10

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
La temperatura ambiente y de entrada debe estar entre 5 °C y 40 °C. p.8 ↗ Operation outside this range requires consultation with the manufacturer; ensure installation room ventilation and cooling air supply. C-VLR 401 | 501 | 651 OXY
La contrapresión máxima admisible es +50 mbar. p.8 ↗ Exhaust line must not be restricted or blocked; higher process back pressures require manufacturer consultation. C-VLR 401 | 501 | 651 OXY
Solo se puede utilizar el tipo de aceite OXY-GEAR-LUBE 160 para la lubricación. p.8 ↗ Wrong oil creates acute fire risk in oxygen service; oil mixed with organic substances must be replaced immediately. C-VLR 401 | 501 | 651 OXY
Funcionamiento continuo permitido a cualquier presión entre 700 mbar (abs.) y 200 mbar (abs.) de presión de entrada. p.16 ↗ Process must remain within this inlet pressure band for continuous duty. C-VLR 401 | 501 | 651 OXY
Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2% de la capacidad de bombeo nominal. p.16 ↗ Size the evacuated volume relative to pump capacity to avoid inadmissible operating conditions. C-VLR 401 | 501 | 651 OXY
Capacidad de bombeo con aspiración libre a 50 Hz: 380 m³/h (VLR 401), 495 m³/h (VLR 501), 650 m³/h (VLR 651). p.16 ↗ Use these values for preliminary sizing; actual capacity depends on intake pressure per data sheet D 886-OXY. C-VLR 401, C-VLR 501, C-VLR 651
La inclinación máxima durante el funcionamiento es de 8° en todas las direcciones; la máquina debe instalarse horizontalmente. p.17 ↗ Mount on a plane, even floor and secure against tipping and falling. C-VLR 401 | 501 | 651 OXY
Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes; el aire de refrigeración no debe recircularse. p.18 ↗ Maintain clearance and prevent hot exhaust air from other machines being drawn into the cooling system. C-VLR 401 | 501 | 651 OXY
Deje al menos 50 cm de espacio alrededor de la máquina para trabajos de mantenimiento. p.17 ↗ Layout installation to allow access to oil filling point, oil sight glass and oil drain. C-VLR 401 | 501 | 651 OXY
El contenido de oxígeno en volumen en el aire de la sala no puede superar el 21% cuando la bomba sopla libremente. p.17 ↗ Install sufficient ventilation; the OXY pump is not gas-tight and can enrich room air with oxygen. C-VLR 401 | 501 | 651 OXY
Desviación de tensión admisible ±5% del valor nominal y desviación de frecuencia ±2%. p.20 ↗ Verify mains conditions against motor data plate before connection. C-VLR 401 | 501 | 651 OXY
Los motores cumplen con DIN EN 60034, clase de protección IP 55 y clase de aislamiento F. p.20 ↗ Suitable for the specified environment; observe motor data plate for actual motor data. C-VLR 401 | 501 | 651 OXY
Las máquinas con motores de CA >1,7 kVA, motores trifásicos >5,2 kVA o motores con corrientes de arranque >60 A no están diseñadas para arranque directo. p.20 ↗ Use star-delta starting, soft starter or frequency converter for such motors; reduce mechanical load during start. C-VLR 401 | 501 | 651 OXY
El sistema de monitorización de presión no está incluido en el alcance de suministro y debe ser instalado por el usuario. p.20 ↗ Install a pressure monitoring device (e.g. pressure switch) that switches off the pump if minimum permissible pressure is undershot; permissible pressure is on the data plate. C-VLR 401 | 501 | 651 OXY
Compruebe el sentido de giro arrancando brevemente el motor (máx. dos segundos); visto desde el ventilador del motor, debe girar en sentido antihorario. p.22 ↗ Use a phase sequence indicator; keep 1 m distance from inlet and outlet connections during the check. C-VLR 401 | 501 | 651 OXY
Antes de una parada superior a 2 horas o de la puesta fuera de servicio, haga funcionar la bomba a 700 mbar (abs.) durante al menos 15–30 minutos con aire seco. p.22 ↗ Removes moisture and pollution that could otherwise prevent restart or damage the machine. C-VLR 401 | 501 | 651 OXY
Temperatura de almacenamiento -20 °C a +70 °C, humedad relativa del aire máx. 80%, sin polvo, seco, sin vibraciones, protegido de la radiación solar; almacenamiento no superior a 6 meses. p.13 ↗ Close openings air-tight during storage; observe storage guidelines I 100 and I 150. C-VLR 401 | 501 | 651 OXY
Reducción de rendimiento notable cuando se instala a más de 1000 m sobre el nivel del mar. p.18 ↗ Contact manufacturer for high-altitude installations. C-VLR 401 | 501 | 651 OXY
Las temperaturas superficiales de los componentes pueden superar los 70 °C a temperatura de funcionamiento. p.21 ↗ Do not touch hot surfaces; wear protective gloves if necessary; provide guarding. C-VLR 401 | 501 | 651 OXY
La máquina no dispone de parada de emergencia ni desconexión de emergencia propias; esto debe ser implementado por el usuario. p.11 ↗ Integrate the machine into the user's safety concept. C-VLR 401 | 501 | 651 OXY

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Machine is switched off by the motor protection switch p.31 ↗ Mains voltage/ Frequency does not correspond with the motor data Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.31 ↗ Connection to motor terminal board is not correct Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.31 ↗ Motor protection switch is not set correctly Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.31 ↗ Motor protection switch is triggered too quickly Use a motor protection switch with an overload-dependent turn-off delay that considers the short excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 102 or IEC 60947-4-1)
Suction capacity is insufficient p.31 ↗ Air filter is polluted Replace air filter Chapter 7.6
Suction capacity is insufficient p.31 ↗ The inlet pipe is too long or too narrow Check the hose and/or the pipe Chapter 5.3
Suction capacity is insufficient p.31 ↗ Machine or system leaking Check the pipework and screw connections for leaks and check for tight fit Chapter 5.3
Final pressure (max. vacuum) is not reached p.31 ↗ Machine or system leaking Check the pipework and screw connections for leaks and check for tight fit Chapter 5.3
Final pressure (max. vacuum) is not reached p.31 ↗ Air filter is polluted Replace air filter Chapter 7.6
Machine gets too hot p.31 ↗ Ambient or inlet temperatures too high Ensure proper use Chapter 2.4
Machine gets too hot p.31 ↗ Cooling air supply is obstructed Check ambient conditions Chapter 5.1
Machine gets too hot p.31 ↗ Cooling air supply is obstructed Clean ventilation slots Chapter 7.4
The machine makes a strange noise p.31 ↗ Deposits on the rotary piston Clean the working space and the rotary piston Elmo Rietschle Service