Operating Instructions — C-VLR 62 vacuum pump (BA 882-PC, ed. 1.0 28.03.2019, EN)
Technical Reference Summary
Covered Models & Document Scope
Abarca las bombas de vacío de garra sin contacto C-VLR 62 y C-VLR 122 con refrigeración pasiva, incluido el modelo estándar (CD) y el modelo con recubrimiento protector contra la corrosión (XD). El documento es el manual de instrucciones BA 882-PC-GB, edición 1.0 de fecha 28.03.2019.
Section-by-Section Technical Breakdown
Describe la construcción y el principio de funcionamiento de las bombas de vacío de garra C-VLR 62 y C-VLR 122. Las bombas son máquinas de pistón rotativo de doble eje con rotores de garra sin contacto y funcionamiento en seco, sincronizados mediante un par de engranajes lubricados con aceite. El documento identifica componentes, conexiones, campos de la placa de características, campos de aplicación y accesorios disponibles.
- C-VLR 62: vacuum connection G 1 1/2, exhaust air outlet, inlet flange with non-return valve, cooling air inlet/outlet, oil filling point, oil sight glass, oil discharge point, exhaust silencer, vacuum relief valve (ZUV).
- C-VLR 122: same as C-VLR 62 plus exhaust air outlet G 1 and condensate drain X.
- Data plate includes type/size, serial number, year of construction, data matrix barcode, item number, speed 50/60 Hz, motor output 50/60 Hz, recommended oil type, operating mode, pumping capacity 50/60 Hz, final pressure (abs.) 50/60 Hz.
- Fields of application: evacuation of closed systems or continuous vacuum within inlet pressure range 400–1000 mbar (abs.); maximum suction capacity 62 m3/h or 120 m3/h at 50 Hz.
- XD model has corrosion-protective coating and is suitable for water-damp gases (water vapour).
- Accessories: intake filter (paper or polyester) and vacuum relief valve (ZUV) set at factory for lowest permissible final pressure.
Proporciona los requisitos para la preparación del lugar de instalación, la instalación mecánica, la conexión de tuberías, la comprobación del nivel de aceite y la conexión eléctrica. Incluye límites de inclinación, espacio libre para el aire de refrigeración, contrapresión y tolerancias eléctricas.
- Machine must be set up horizontally; maximum inclination 8° in all directions.
- Cooling air inlets and outlets must be at least 30 cm away from adjacent walls.
- Maximum permissible back pressure: +50 mbar.
- Only screw in pipes by hand; use flexible connections if necessary.
- Oil level must be checked through the oil sight glass and topped up to the middle of the sight glass.
- Electrical installation by qualified electrician per EN 60204; motor protection circuit breaker required.
- Permissible voltage deviation ±5%, frequency deviation ±2%.
- Motors comply with DIN EN 60034, protection class IP 55, insulation class F.
Abarca las comprobaciones de arranque, la verificación del sentido de giro, el procedimiento de postfuncionamiento, los pasos de puesta fuera de servicio y la puesta en servicio de nuevo. Incluye advertencias de seguridad para superficies calientes, peligros de aspiración y ruido.
- Check rotation direction with phase sequence indicator; when looking at motor blower, it must rotate counter-clockwise.
- Start motor briefly (max. two seconds) to check direction of rotation.
- Before putting out of operation for more than 2 hours, run pump at -700 mbar (abs.) for at least 15–30 minutes with dry air.
- Drain condensate from silencer (VLR 122) before decommissioning.
- Decommissioning: switch off, allow to cool, close cut-off devices, disconnect power, depressurise slowly, remove pipes, drain condensate, seal connections.
Define los intervalos de mantenimiento y los procedimientos para el cambio de aceite, la limpieza/sustitución del filtro de aire y la inspección del acoplamiento. Incluye instrucciones de seguridad e información para el pedido de piezas de repuesto.
- Monthly: check pipes and screws for leaks, clean ventilation slots, check oil level, check/clean/replace air filters, drain condensate (VLR 122).
- Oil change every 20,000 operating hours; extreme load can reduce oil life to 5,000 hours.
- Oil type: Elmo Rietschle GEAR-LUBE 150 synthetic oil, viscosity ISO VG 150 per DIN 3448.
- Check couplings for wear at least once per year.
- General overhaul at 40,000 hours by Elmo Rietschle Service.
- Mesh filter: clean or replace monthly by washing or blowing off.
- Intake filter cartridge: clean monthly, replace every six months.
Tabla de resolución de problemas que enumera fallos, causas probables y acciones correctivas. Abarca disparos del interruptor de protección del motor, capacidad de aspiración insuficiente, no alcanzar la presión final, sobrecalentamiento y ruidos anómalos.
- Machine switched off by motor protection switch: check mains voltage/frequency, motor terminal connection, motor protection switch setting.
- Suction capacity insufficient: clean/replace air filter, check inlet pipe length/diameter, check for leaks.
- Final pressure not reached: check for leaks, clean/replace air filter.
- Machine gets too hot: check ambient/inlet temperatures, cooling air supply, clean ventilation slots.
- Strange noise: clean working space and rotary piston; contact Elmo Rietschle Service.
Enumera las especificaciones técnicas para C-VLR 62 y C-VLR 122, incluidos nivel de presión sonora, peso, dimensiones, conexiones, volumen de aceite, tensión, corriente y potencia del motor.
- C-VLR 62: sound pressure level 79 dB(A) at 50 Hz, 82 dB(A) at 60 Hz; sound power level 85 dB(A).
- C-VLR 62: weight 70 kg, length 707 mm, width 439 mm, height 277 mm.
- C-VLR 122: weight 90 kg, length 776 mm, width 378 mm, height 277 mm.
- Vacuum connection G 1 1/2; oil filled volume 0.43 l.
- Rated voltage 3~: 230/400 V ±10% at 50 Hz; 265/460 V ±10% at 60 Hz.
- Current consumption C-VLR 62: 4.89/2.81 A at 50 Hz; 4.84/2.79 A at 60 Hz.
- Motor output C-VLR 62: 1.25 kW at 50 Hz; 1.5 kW at 60 Hz.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Inclinación máxima para el funcionamiento: 8° en todas las direcciones. p.16 ↗ | Machine must be installed horizontally; ensure floor is plane and even. | C-VLR 62 and C-VLR 122 |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.16 ↗ | Ensure sufficient clearance for cooling air flow to prevent overheating. | C-VLR 62 and C-VLR 122 |
| Contrapresión máxima admisible: +50 mbar. p.17 ↗ | Do not close or restrict exhaust air openings; prevent liquid accumulation in exhaust line. | C-VLR 62 and C-VLR 122 |
| Desviación de tensión admisible: ±5%; desviación de frecuencia: ±2%. p.18 ↗ | Verify mains supply matches motor data plate before connection. | C-VLR 62 and C-VLR 122 |
| Protección del motor: IP 55, clase de aislamiento F, según DIN EN 60034. p.18 ↗ | Use motor protection circuit breaker with delayed switch off to accommodate temporary excess current at cold start. | C-VLR 62 and C-VLR 122 |
| Intervalo de cambio de aceite: 20.000 horas de funcionamiento; una carga extrema puede reducirlo a 5.000 horas. p.23 ↗ | Use Elmo Rietschle approved oil (GEAR-LUBE 150, ISO VG 150) to maintain interval. | C-VLR 62 and C-VLR 122 |
| Volumen de aceite llenado: 0,43 l. p.31 ↗ | Fill oil to middle of sight glass; if changing oil type, empty tank completely. | C-VLR 62 and C-VLR 122 |
| Aceite recomendado: aceite sintético GEAR-LUBE 150, viscosidad ISO VG 150 según DIN 3448. p.25 ↗ | Use only approved oil to maintain warranty and performance. | C-VLR 62 and C-VLR 122 |
| Procedimiento de postfuncionamiento: funcionar a -700 mbar (abs.) durante al menos 15–30 minutos con aire seco antes de la parada >2 horas. p.20 ↗ | Prevents condensate and impurity deposits that can damage machine. | C-VLR 62 and C-VLR 122 |
| Comprobación del sentido de giro: arrancar el motor brevemente (máx. 2 segundos); visto desde el ventilador del motor, debe girar en sentido antihorario. p.20 ↗ | Wrong rotation can damage machine and cause injury; use phase sequence indicator. | C-VLR 62 and C-VLR 122 |
| Capacidad de aspiración máxima: 62 m3/h o 120 m3/h a 50 Hz. p.15 ↗ | Select model based on required pumping speed; inlet pressure range 400–1000 mbar (abs.). | C-VLR 62 (62 m3/h) and C-VLR 122 (120 m3/h) |
| Nivel de presión sonora: 79 dB(A) a 50 Hz, 82 dB(A) a 60 Hz (C-VLR 62); tolerancia ±3 dB(A). p.31 ↗ | Use ear protection when spending long time near running machine. | C-VLR 62 |
| Peso: C-VLR 62 = 70 kg; C-VLR 122 = 90 kg. p.31 ↗ | Ensure bearing surface can carry weight; secure machine against tipping. | C-VLR 62 and C-VLR 122 |
| Tensión nominal 3~: 230/400 V ±10% a 50 Hz; 265/460 V ±10% a 60 Hz. p.31 ↗ | Verify motor data plate matches mains network. | C-VLR 62 |
| Potencia del motor: 1,25 kW a 50 Hz; 1,5 kW a 60 Hz (C-VLR 62). p.31 ↗ | Size motor protection and supply accordingly. | C-VLR 62 |
| Rango de temperatura ambiente y de entrada: 5 a 40 °C. p.7 ↗ | Contact manufacturer for temperatures outside this range. | C-VLR 62 and C-VLR 122 |
| Condiciones de almacenamiento: humedad relativa 0–80%, temperatura -10 a +60 °C, máx. 6 meses. p.11 ↗ | Store in dry, dust-free, vibration-free environment. | C-VLR 62 and C-VLR 122 |
| La rueda dentada del acoplamiento debe comprobarse en busca de desgaste al menos una vez al año. p.28 ↗ | Frequent starting and high ambient temperature reduce sprocket lifetime. | C-VLR 62 and C-VLR 122 |
| El cartucho del filtro de aspiración debe sustituirse cada seis meses. p.27 ↗ | Clean monthly by blowing off from inside to outside; separation efficiency deteriorates with cleaning. | C-VLR 62 and C-VLR 122 with intake filter accessory |
| Revisión general a las 40.000 horas por Elmo Rietschle Service. p.23 ↗ | Plan for service intervention at this interval. | C-VLR 62 and C-VLR 122 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| The machine is switched off by the motor protection switch p.30 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Get it checked by an electrician | Chapter 5.5 |
| The machine is switched off by the motor protection switch p.30 ↗ | Connection to motor terminal board is not correct | Get it checked by an electrician | Chapter 5.5 |
| The machine is switched off by the motor protection switch p.30 ↗ | Motor protection switch is not set correctly | Get it checked by an electrician | Chapter 5.5 |
| Motor protection switch is triggered too quickly p.30 ↗ | Motor protection switch is not set correctly | Use a motor protection switch with an overload-dependent turn-off delay that considers the short excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 102 or IEC 60947-4-1) | |
| Suction capacity is insufficient p.30 ↗ | Air filter is polluted | Clean / replace the air filter | Chapter 7.2.2, Chapter 7.4 |
| Suction capacity is insufficient p.30 ↗ | The inlet pipe is too long or too narrow | Check the hose and/or the pipe | Chapter 5.3 |
| Suction capacity is insufficient p.30 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Final pressure (max. vacuum) is not reached p.30 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Final pressure (max. vacuum) is not reached p.30 ↗ | Air filter is polluted | Clean / replace the air filter | Chapter 7.2.2, Chapter 7.4 |
| Machine gets too hot p.30 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.3 |
| Machine gets too hot p.30 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Machine gets too hot p.30 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.2 |
| The machine makes a strange noise p.30 ↗ | Deposits on the rotary piston | Clean the working space and the rotary piston | Elmo Rietschle Service |