Operating Instructions — C-VLR 401 vacuum pump (BA 886-70-FU, EN)
Technical Reference Summary
Covered Models & Document Scope
Abarca las bombas de vacío de garras de funcionamiento sin contacto C-VLR 401 y C-VLR 501 con convertidor de frecuencia integrado (VSD, Fxxx). La versión estándar maneja gases secos; la versión "XD" dispone de recubrimiento protector contra la corrosión y purga de condensado para gases con humedad de agua. Documento BA 886-70-FU-EN, edición 1.0, 10.2017.
Section-by-Section Technical Breakdown
Describe la disposición de la máquina, las placas de características, el principio de funcionamiento y los límites de aplicación. La bomba es una bomba de pistón rotativo de garras secas de doble eje con lubricación por aceite de engranajes, válvula antirretorno, microfiltro y convertidor de frecuencia integral para velocidad infinitamente variable. Se permite el funcionamiento continuo entre 700 mbar (abs.) y 200 mbar (abs.) de presión de aspiración.
- Connection flange on inlet side, exhaust silencer on pressure side; non-return valve prevents ventilation of the evacuated system after stop.
- Counter-rotating claw rotors synchronised by oil-lubricated gear pair; gearbox and compression chamber separated by special seals.
- Cooling air drawn between machine and insulating hood by drum fan; cooling air inlet and outlet must be at least 30 cm from adjacent walls.
- Continuous operation at any pressure between 700 mbar (abs.) and 200 mbar (abs.) inlet pressure.
- When evacuating closed systems, volume to be evacuated must be no more than 2 % of nominal suction capacity.
- Suction capacity with unrestricted suction: 380 m3/h (C-VLR 401) and 495 m3/h (C-VLR 501) at 50 Hz.
- Version "XD" suitable for water-moist gases (water vapour); standard version for non-explosive, non-inflammable, non-aggressive, non-poisonous dry gases and gas-air mixtures.
- Ambient and suction temperature range 5 to 40 °C; contact manufacturer outside this range.
- Frequent switching (about 10 times per hour) or high ambient/intake temperatures may exceed motor winding and bearing temperature limits.
Abarca la preparación, la instalación mecánica, la conexión de tuberías, el llenado de aceite y la conexión eléctrica del accionamiento. La máquina debe instalarse horizontalmente sobre una base nivelada y recta capaz de soportar su peso; las entradas/salidas de aire de refrigeración requieren al menos 30 cm de espacio libre. La instalación eléctrica debe ser realizada por un electricista cualificado según EN 60204, y el convertidor de frecuencia debe conectarse conforme a sus propias instrucciones de funcionamiento.
- Machine freely accessible from all sides; ventilation grids and holes must not be closed.
- Oil filling point, oil sight glass and oil outlets must be easily accessible.
- Cooling air inlets and outlets at least 30 cm away from adjacent walls; discharged cooling air must not be re-sucked.
- Machine may only be operated when set up horizontally; foundation level and straight and able to take machine weight.
- Installation on a firm base without anchoring is possible; on a substructure, fixing with flexible buffers is recommended.
- Power reduction noticeable above 1000 m above sea level; contact manufacturer.
- C-VLR 501 must not be operated without covering plates.
- Pipes must only be screwed in by hand; exhaust air must not be restricted (max. pressure difference 50 mbar).
- Fill lubricating oil up to the middle of the sight glasses.
- Frequency converter supply: 3 AC 400 V -15 % to 480 V +10 %, input frequency 47 to 63 Hz, network configurations TN/TT.
- For IP 65, suitable cable glands or shutters must be provided.
Abarca la primera puesta en marcha, la comprobación del sentido de giro, la recomendación de postfuncionamiento, la parada/almacenamiento y la nueva puesta en marcha. El ventilador del motor debe girar en sentido antihorario visto desde el ventilador; se utiliza un indicador de secuencia de fases para verificar el campo giratorio horario. Se recomienda un postfuncionamiento a 700 mbar (abs.) durante aproximadamente 15 a 30 minutos para eliminar la humedad y las impurezas.
- Intended direction of rotation shown by rotary direction arrow; when looking at the motor fan it must rotate anti-clockwise.
- Start motor briefly (max. two seconds) to check direction of rotation; use a phase sequence indicator (clockwise rotating field).
- Post-run at 700 mbar (abs.) for approximately 15 to 30 minutes to remove accrued dampness and impurities.
- Version "XD": drain condensate periodically from the silencer depending on application; do not drain at operating temperature.
- Machine must only be switched on again after it stops.
- Surface temperatures on marked components may exceed 70 °C at operating temperature.
- Decommissioning: switch off, close cut-off devices, disconnect from electricity, depressurise slowly, remove pipes, drain condensate (XD), seal connections with adhesive foil.
Define los intervalos de mantenimiento y los procedimientos para los cambios de aceite, la limpieza del filtro de aire, la inspección del acoplamiento y el convertidor de frecuencia integrado. El aceite debe cambiarse cada 20.000 horas de funcionamiento con aceite ISO VG 150 / CLP HC 150; el filtro de malla se limpia o se sustituye según la carga de suciedad; el piñón del acoplamiento se comprueba al menos una vez al año.
- Monthly: check pipes and screws for leaks and proper seating; check terminal box and cable inlet holes for leaks; clean ventilation slots and motor cooling ribs; check oil level.
- Depending on application, at least monthly: drain condensate from silencer (version "XD").
- Every 20,000 operating hours: change oil.
- Clean intake air filter depending on how dirty the discharged medium is.
- At least once a year: check coupling wear.
- Oil viscosity must comply with ISO VG 150 per DIN 51519; designation per DIN 51502: CLP HC 150; recommended GEAR-LUBE 150 or equivalent.
- Change oil at operating temperature in an atmospherically ventilated area; if not completely emptied, refill amount is reduced.
- If changing oil type, completely empty oil removing device housing and oil cooler.
- Coupling sprocket subject to wear; defective sprocket may lead to rotor shaft breaking.
- Frequent starting and high ambient temperature reduce coupling sprocket service life.
- For repairs, a fully completed, signed declaration of harmlessness must accompany each machine sent to an Elmo Rietschle Service centre.
- Only use original spare parts or parts approved by the manufacturer.
Enumera los datos mecánicos y acústicos clave para C-VLR 401 y C-VLR 501. Se indican el nivel de presión sonora, el peso, las dimensiones, los tamaños de conexión y la cantidad de aceite; más datos en la hoja de datos D 886-60.
- Sound pressure level (max.) per EN ISO 3744, tolerance ±3 dB(A): C-VLR 401 79 dB(A) at 50 Hz, 82 dB(A) at 60 Hz.
- Weight: C-VLR 401 470 kg, C-VLR 501 510 kg (may differ depending on motor manufacturer).
- Length: C-VLR 401 1169 mm, C-VLR 501 1143 mm; width 598 mm; height 963 mm.
- Vacuum connection G 3; exhaust air outlet G 3; condensate drain silencer G ½.
- Correct amount of oil: C-VLR 401 1.75 l, C-VLR 501 1.8 l.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Funcionamiento continuo permitido a cualquier presión entre 700 mbar (abs.) y 200 mbar (abs.) de presión de aspiración. p.14 ↗ | Select and set the process operating window within this range; operation outside may be outside designated use. | C-VLR 401 and C-VLR 501 |
| Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad de aspiración nominal. p.14 ↗ | Size evacuated volumes accordingly to avoid excessive evacuation times or pump overload. | C-VLR 401 and C-VLR 501 |
| Capacidad de aspiración con aspiración sin restricciones de 380 m3/h (C-VLR 401) y 495 m3/h (C-VLR 501) a 50 Hz. p.14 ↗ | Use these values for preliminary sizing; refer to data sheet D 886-60 for suction capacity versus intake pressure. | C-VLR 401 and C-VLR 501 |
| La temperatura ambiente y de aspiración debe estar entre 5 y 40 °C. p.7 ↗ | Install in a location and process where both ambient and intake temperatures remain within this range; contact manufacturer outside. | C-VLR 401 and C-VLR 501 |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.15 ↗ | Maintain clearance during installation to ensure adequate cooling and avoid recirculation of heated air. | C-VLR 401 and C-VLR 501 |
| El aire de escape no debe restringirse; no debe haber sistemas de bloqueo en el tubo de escape, diferencia de presión máx. 50 mbar. p.16 ↗ | Design exhaust piping without valves or restrictions exceeding 50 mbar differential; check exhaust pipe regularly for impurities. | C-VLR 401 and C-VLR 501 |
| Tensión de entrada del convertidor de frecuencia 3 AC 400 V -15 % a 480 V +10 %, frecuencia de entrada 47 a 63 Hz, configuraciones de red TN/TT. p.17 ↗ | Verify site supply and earthing system match these values before connecting the drive. | C-VLR 401 and C-VLR 501 VSD |
| Para la protección IP 65, deben preverse prensaestopas o obturadores adecuados. p.17 ↗ | Select and install cable entries rated for IP 65 to maintain the frequency converter enclosure rating. | C-VLR 401 and C-VLR 501 VSD |
| El ventilador del motor debe girar en sentido antihorario visto desde el ventilador; utilice un indicador de secuencia de fases para verificar el campo giratorio horario. p.19 ↗ | Check rotation direction before commissioning; wrong direction damages the machine. | C-VLR 401 and C-VLR 501 |
| Postfuncionamiento recomendado a 700 mbar (abs.) durante aproximadamente 15 a 30 minutos. p.19 ↗ | Use post-run to remove dampness and impurities and reduce risk of deposits preventing restart. | C-VLR 401 and C-VLR 501 |
| Intervalo de cambio de aceite cada 20.000 horas de funcionamiento con operaciones limpias. p.22 ↗ | Plan maintenance intervals accordingly; use oil meeting ISO VG 150 / CLP HC 150. | C-VLR 401 and C-VLR 501 |
| La viscosidad del aceite debe cumplir ISO VG 150 según DIN 51519; designación según DIN 51502: CLP HC 150; recomendado GEAR-LUBE 150 o equivalente. p.22 ↗ | Select only compatible lubricants; if changing oil type, completely empty oil removing device housing and oil cooler. | C-VLR 401 and C-VLR 501 |
| Cantidad de aceite correcta: 1,75 l (C-VLR 401), 1,8 l (C-VLR 501). p.28 ↗ | Fill to middle of sight glass; use quantity as reference for oil changes. | C-VLR 401 and C-VLR 501 |
| El piñón del acoplamiento debe comprobarse al menos una vez al año; un piñón defectuoso puede provocar la rotura del eje del rotor. p.24 ↗ | Include annual coupling inspection in maintenance plan; replace worn or damaged sprocket. | C-VLR 401 and C-VLR 501 |
| Nivel de presión sonora (máx.) según EN ISO 3744, tolerancia ±3 dB(A): 79 dB(A) a 50 Hz y 82 dB(A) a 60 Hz. p.28 ↗ | Use ear protectors for prolonged presence near the running machine. | C-VLR 401 and C-VLR 501 |
| Conexión de vacío G 3, salida de aire de escape G 3, silenciador de purga de condensado G ½. p.28 ↗ | Select mating pipework and fittings accordingly; screw pipes in by hand only. | C-VLR 401 and C-VLR 501 |
| Peso 470 kg (C-VLR 401) y 510 kg (C-VLR 501); longitud 1169 mm y 1143 mm; anchura 598 mm; altura 963 mm. p.28 ↗ | Foundation and lifting equipment must be sized for these masses and dimensions; weight/length may differ depending on motor manufacturer. | C-VLR 401 and C-VLR 501 |
| Reducción de potencia apreciable cuando se instala a más de 1000 m sobre el nivel del mar. p.15 ↗ | Contact manufacturer for installation at altitude above 1000 m. | C-VLR 401 and C-VLR 501 |
| C-VLR 501 no debe funcionar sin placas de cubierta. p.15 ↗ | Ensure covering plates are fitted before commissioning the C-VLR 501. | C-VLR 501 |
| Condiciones ambientales de almacenamiento: humedad relativa 0 % a 80 %, temperatura de almacenamiento -20 °C a +70 °C; no almacenar durante más de 6 meses. p.11 ↗ | Respect storage limits before installation; refer to machine storage guidelines I 150 for longer storage. | C-VLR 401 and C-VLR 501 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Maschine does not run or the frequency converter shows an error message p.27 ↗ | Technical fault of the integrated frequency converter | see enclosed operating instructions 610.00260.40.000 Section 8 | Section 8 |
| Suction capacity is insufficient p.27 ↗ | The mesh filter is dirty | Clean or replace the filter | Section 7.2.2, Section 7.4 |
| Suction capacity is insufficient p.27 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.27 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Machine gets too hot p.27 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.27 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.27 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| The machine makes an abnormal noise p.27 ↗ | Deposits on the rotary piston | Clean the working space and the rotary piston | Elmo Rietschle Service |