Operating Instructions — C-VLR 401 vacuum pump (BA 886-EN, ed. 1.1 12.04.2021, EN)
Technical Reference Summary
Covered Models & Document Scope
Cubre las bombas de vacío de garra de funcionamiento sin contacto C-VLR 401 y C-VLR 501 (serie C), incluidos el diseño estándar CD y el diseño de protección contra la corrosión XD. Documento BA 886-EN, edición 1.1, 12.04.2021.
Section-by-Section Technical Breakdown
Describe las C-VLR 401 y C-VLR 501 como bombas de vacío de pistón rotativo de doble eje con rotores de garra de funcionamiento en seco sin contacto, sincronizados mediante un par de engranajes lubricados con aceite. La caja de engranajes y la cámara de compresión están separadas por sellos especiales; la bomba dispone de brida de aspiración, silenciador de escape, filtro de aspiración de malla, válvula antirretorno integrada y válvula de alivio de vacío. La refrigeración se realiza mediante un ventilador de tambor que aspira aire entre el compresor y la campana de aislamiento.
- Double-shaft rotary piston (claw) design, contact-free and dry running
- Gear pair in oil-filled gearbox synchronises counter-rotating rotors
- Integral non-return valve prevents ventilation of evacuated system after stop
- Vacuum relief valve incorporated into the machine
- Insulation hood with drum fan for cooling air; driven via coupling by flanged three-phase standard motor
- XD model has corrosion-protective coating and condensate drain (Fig. 2/B2)
Define el funcionamiento continuo entre 700 mbar (abs.) y una presión de aspiración de 200 mbar (abs.). Para la evacuación de sistemas cerrados, el volumen no debe superar el 2 % de la capacidad nominal de bombeo. La capacidad de bombeo de aspiración libre es de 380 m3/h y 495 m3/h a 50 Hz. El diseño XD es adecuado para gases con humedad de agua (vapor de agua).
- Continuous operation at any pressure between 700 mbar (abs.) and 200 mbar (abs.) inlet pressure
- Closed-system volume to be evacuated ≤ 2% of nominal pumping capacity
- Free intake pumping capacity: 380 m3/h (C-VLR 401) and 495 m3/h (C-VLR 501) at 50 Hz
- XD design suitable for conveying water-damp gases (water vapour)
- Frequent switching (approx. 10 times per hour) or high ambient/inlet temperatures may exceed motor winding and bearing temperature limits — contact manufacturer
- Outdoor installation requires protection from environmental influences (e.g. protective roof)
Cubre la preparación, la instalación mecánica, la conexión de tuberías, la comprobación del aceite y la conexión eléctrica. La máquina debe instalarse horizontalmente con una inclinación máxima de 8° en todas las direcciones, con al menos 50 cm de espacio de mantenimiento y 30 cm de separación de las paredes para el aire de refrigeración. La instalación eléctrica debe ser realizada por un electricista cualificado según EN 60204, con interruptor de protección del motor e interruptor principal proporcionados por el usuario.
- Max. inclination 8° in all directions; floor must be plane and even
- Maintenance space at least 50 cm around machine
- Cooling air inlets/outlets at least 30 cm from adjacent walls; exhaust air must not be re-sucked
- Ambient temperature min. +5 °C, max. +40 °C
- Maximum permissible back pressure +50 mbar; exhaust air opening must not be closed or restricted
- Only screw in pipes by hand; use flexible connections/compensators if necessary
- Oil level filled to middle of sight glass
- Electrical installation per EN 60204 by qualified electrician; main switch and motor protection switch provided by user
- Permissible tolerances: ±5% voltage deviation, ±2% frequency deviation
- Motor protection class IP 55, insulation class F, per DIN EN 60034
La puesta en marcha requiere una comprobación de la instalación y una comprobación del sentido de giro. El motor debe girar en sentido antihorario visto desde el ventilador del motor; utilice un indicador de secuencia de fases y mantenga una distancia de 1 m desde la aspiración/escape. Antes de la puesta fuera de servicio o de una parada >2 horas, haga funcionar la bomba a 700 mbar (abs.) con aire seco durante 15–30 minutos para eliminar la humedad y la suciedad.
- Installation check: no transport damage, horizontal safe standing, leak-tight pipe connections, tight screw/flange connections, correct electrical installation, adequate ventilation, oil filled and level checked, pump and pipelines cleaned
- Check rotation direction with phase sequence indicator; brief start max. 2 seconds; motor blower must rotate counter-clockwise
- Keep 1 m distance from outlet and inlet connections during rotation check
- Before shutdown >2 hours or decommissioning: run at 700 mbar (abs.) with dry air for at least 15–30 minutes
- XD model: regularly discharge condensate from silencer through condensate drain; wear protective gloves
- Decommissioning: drain condensate, switch off, allow to cool, close cut-off devices, disconnect power, depressurise slowly, remove pipes, seal connections with adhesive foil
El mantenimiento incluye la limpieza de la bomba de vacío, la comprobación/relleno del aceite lubricante, el cambio de aceite, la limpieza/sustitución de los filtros de aire (filtro de malla y filtro de aspiración opcional) y las comprobaciones del motor/acoplamiento. Los intervalos de limpieza y cambio de aceite dependen de la carga y del tipo de aceite. Los trabajos de reparación solo deben ser realizados por especialistas autorizados; piezas de repuesto según la lista E 886.
- Disconnect power and secure against accidental switching before maintenance
- Allow machine to cool down before maintenance; surfaces may exceed 70 °C
- Safety devices and guards on motor fans and ventilators must not be removed
- Cleaning and oil change intervals depend on operating time, operating conditions and oil type
- Oil change and suitable oil types per chapter 7.5.2
- Air filter: clean/replace mesh filter; intake filter is an accessory
- Repair works only by authorised specialists; use original spare parts
Tabla de solución de problemas que cubre disparos del interruptor de protección del motor, capacidad de aspiración insuficiente, no alcanzar la presión final, sobrecalentamiento y ruidos extraños. Enumera causas y remedios con referencias a los capítulos correspondientes. Para otras anomalías, contacte con Elmo Rietschle Service.
- Never restart pump after automatic shut-off without finding and remedying the cause
- Motor protection switch must have overload-dependent turn-off delay considering short excess current at start-up (VDE 0660 Part 102 or IEC 60947-4-1)
- Insufficient suction capacity causes: polluted air filter, inlet pipe too long/narrow, leaking machine/system
- Final pressure not reached causes: leaking machine/system, polluted air filter
- Overheating causes: ambient/inlet temperatures too high, obstructed cooling air supply
- Strange noise cause: deposits on rotary piston — clean working space and rotary piston
Capítulo de datos técnicos al que se hace referencia para el peso, el nivel de presión sonora y otros datos de rendimiento. Los valores específicos se proporcionan en la hoja de datos D 890.
- Technical data per chapter 10 and data sheet D 890
- Sound pressure level per EN ISO 3744
- Weight and bearing surface load per chapter 10
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Funcionamiento continuo permitido a cualquier presión entre 700 mbar (abs.) y una presión de aspiración de 200 mbar (abs.). p.16 ↗ | Select pump for applications within this inlet pressure range; operation outside requires consultation with manufacturer. | C-VLR 401 and C-VLR 501 |
| Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad nominal de bombeo de la bomba de vacío. p.16 ↗ | Size closed-system evacuation volumes accordingly to avoid excessive evacuation times or pump overload. | C-VLR 401 and C-VLR 501 |
| La capacidad de bombeo de aspiración libre es de 380 m3/h (C-VLR 401) y 495 m3/h (C-VLR 501) a 50 Hz. p.16 ↗ | Use these values for initial sizing; actual capacity depends on intake pressure per data sheet D 890. | C-VLR 401 and C-VLR 501 |
| La contrapresión máxima admisible es de +50 mbar. p.8 ↗ | Exhaust lines must be sized and routed to avoid exceeding +50 mbar back pressure; do not install blocking devices. | C-VLR 401 and C-VLR 501 |
| La temperatura ambiente y de aspiración debe estar entre 5 °C y 40 °C. p.8 ↗ | Ensure installation room ventilation and process conditions stay within this range; contact manufacturer for temperatures outside range. | C-VLR 401 and C-VLR 501 |
| La máquina solo puede funcionar horizontalmente con una inclinación máxima de 8° en todas las direcciones. p.17 ↗ | Mount on a plane, even floor; secure against tipping and falling. | C-VLR 401 and C-VLR 501 |
| Las entradas y salidas de aire de refrigeración deben estar a al menos 30 cm de las paredes adyacentes; el aire de refrigeración que sale no debe volver a aspirarse. p.17 ↗ | Maintain clearance for adequate cooling and prevent hot air recirculation to avoid overheating. | C-VLR 401 and C-VLR 501 |
| Para los trabajos de mantenimiento, prever un espacio de al menos 50 cm alrededor de la máquina. p.17 ↗ | Plan installation layout with sufficient access for maintenance and pipe removal. | C-VLR 401 and C-VLR 501 |
| Desviación de tensión admisible ±5 %, desviación de frecuencia ±2 %. p.19 ↗ | Verify mains supply quality at installation location against motor data plate before connection. | C-VLR 401 and C-VLR 501 |
| Los motores cumplen con DIN EN 60034, clase de protección IP 55, clase de aislamiento F. p.19 ↗ | Suitable for dusty and damp environments per IP 55; verify environmental conditions. | C-VLR 401 and C-VLR 501 |
| El motor debe girar en sentido antihorario visto desde el ventilador del motor; comprobar con un indicador de secuencia de fases y un arranque breve máximo de 2 segundos. p.21 ↗ | Wrong rotation direction can damage machine and cause injury; verify before commissioning. | C-VLR 401 and C-VLR 501 |
| Antes de una parada >2 horas o de la puesta fuera de servicio, hacer funcionar la bomba a 700 mbar (abs.) con aire seco durante al menos 15–30 minutos. p.22 ↗ | Prevents condensate and impurity deposits on rotors and casing that could prevent restart. | C-VLR 401 and C-VLR 501 |
| El nivel de aceite debe llenarse hasta la mitad del visor de aceite. p.18 ↗ | Check oil level through sight glass before commissioning and top up at oil filling point as needed. | C-VLR 401 and C-VLR 501 |
| Rango de temperatura de almacenamiento: -20 °C a +70 °C; humedad relativa del aire máxima 80 %; almacenamiento no superior a 6 meses. p.13 ↗ | Store in dry, dust-free, vibration-free, sun-protected area with openings sealed air-tight. | C-VLR 401 and C-VLR 501 |
| Reducción de potencia notable cuando se instala a más de 1000 m sobre el nivel del mar. p.18 ↗ | Contact manufacturer for high-altitude installations to account for reduced pumping capacity. | C-VLR 401 and C-VLR 501 |
| El modelo XD es adecuado para transportar gases con humedad de agua (vapor de agua) y dispone de un drenaje de condensado en el silenciador. p.8 ↗ | Select XD variant for humid or water-vapour applications; regularly discharge condensate. | XD model |
| El interruptor de protección del motor debe tener un retardo de desconexión dependiente de la sobrecarga que considere la breve corriente excesiva en el arranque (VDE 0660 Parte 102 o IEC 60947-4-1). p.19 ↗ | Prevents nuisance tripping during cold starts; select motor protection circuit breaker accordingly. | C-VLR 401 and C-VLR 501 |
| La válvula antirretorno integrada impide la ventilación del sistema evacuado después de la parada de la bomba y no debe desmontarse. p.15 ↗ | Do not remove non-return valve during installation or maintenance. | C-VLR 401 and C-VLR 501 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.30 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.30 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.30 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.30 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent turn-off delay that considers the short excess current at start up (version with short circuit and overload trigger as per VDE 0660 Part 102 or IEC 60947-4-1) | |
| Suction capacity is insufficient p.30 ↗ | Air filter is polluted | Clean/replace air filter | Chapter 7.6, Chapter 7.9 |
| Suction capacity is insufficient p.30 ↗ | The inlet pipe is too long or too narrow | Check the hose and/or the pipe | Chapter 5.3 |
| Suction capacity is insufficient p.30 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and check for tight fit | Chapter 5.3 |
| Final pressure (max. vacuum) is not reached p.30 ↗ | Machine or system leaking | Check the pipework and screw connections for leaks and check for tight fit | Chapter 5.3 |
| Final pressure (max. vacuum) is not reached p.30 ↗ | Air filter is polluted | Clean/replace air filter | Chapter 7.6, Chapter 7.9 |
| Machine gets too hot p.30 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.4 |
| Machine gets too hot p.30 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Machine gets too hot p.30 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.4 |
| The machine makes a strange noise p.30 ↗ | Deposits on the rotary piston | Clean the working space and the rotary piston | Elmo Rietschle Service |