BINDER MK 240 CO₂
BINDER MK 240 CO₂ — Climate chambers.
The MK 240 CO₂ is a 228 L alternating climate chamber with a CO₂ (R744) refrigeration circuit, extending the MK series range down to -50 °C. It is the CO₂-refrigerant modification of the MK 240, distinguished from the standard MK 240 (-40 °C) by its lower temperature limit and high-pressure refrigerant. It serves rapid temperature-change testing of components and materials under program control.
BINDER MK Series — Model Comparison & Selection
| Model | Temperature, °C | Depth, cm | Height, cm | Interior height, mm | Interior volume, L | Interior width, mm |
|---|---|---|---|---|---|---|
| MK 240 CO₂ Current | -50...180 | 92.5 | 171 | 700 | 228 | 735 |
| MK 1020 | -40–180 | 148 | 200.5 | 1020 | 991 | 1200 |
| MK 1020 CO₂ | -48–180 | 148 | 200.5 | 1020 | 991 | 1200 |
| MK 115 | -40–180 | 86.5 | 172.5 | 480 | 115 | 600 |
| MK 240 | -40–180 | 92.5 | 171 | 700 | 228 | 735 |
| MK 400 | -40–180 | 140 | 171 | 700 | 417 | 735 |
| MK 400 CO₂ | -50...180 | 140 | 171 | 700 | 417 | 735 |
| MK 56 | -40–180 | 77.8 | 144.5 | 420 | 60 | 400 |
| MK 720 | -40–180 | 114 | 200.5 | 1020 | 734 | 1200 |
| MK 720 CO₂ | -48–180 | 114 | 200.5 | 1020 | 734 | 1200 |
Full specifications
| Temperature | -50...180 |
| Interior volume | 228 L |
| Load per rack | 30 kg (MK240CO2-400V, 50 Hz) |
| Nominal power | 5.2 kW |
| Article Number mfr | 9020 |
| Depth | 925 mm (MK240CO2-400V, 50 Hz) |
| Height | 1710 mm (MK240CO2-400V, 50 Hz) |
| Interior height | 700 mm (MK240CO2-400V, 50 Hz) |
| Interior width | 735 mm (MK240CO2-400V, 50 Hz) |
| Width | 1115 mm (MK240CO2-400V, 50 Hz) |
| Net weight of the unit (empty) mfr | 311 kg |
| Power frequency | 50 Hz |
| Rated voltage | 400 V |
| Unit fuse | 16.0 A |
| Phase (Nominal voltage) mfr | 3 N/PE |
| Cooling down time from 180°C to -40°C mfr | 60 min |
| Average heating-up rate according to IEC 60068-3-5 between -40°C and 180°C mfr | 5.5 K/min |
Description
Construction and series positioning
- The MK 240 CO₂ is the 228 L member of the MK (E6) alternating climate chamber series, built around a CO₂ (R744) refrigerating circuit with 1.40 kg charge and a maximum system pressure of 120 bar.
- Within the series it sits between the standard MK 240 (-40 °C) and the larger MK 1020 CO₂; its -50 °C lower limit is the defining difference from the non-CO₂ MK 240.
- Interior dimensions 735 × 700 mm (W × H), net depth 925 mm, net width 1,115 mm, net height 1,710 mm; empty weight 311 kg. Rack load is limited to 30 kg per rack.
Thermal behavior
- Working range -50…180 °C. Temperature uniformity 0.1…1.2 K and fluctuation 0.1…0.4 K, both dependent on set value.
- Average heating rate 5.5 K/min between -40 °C and 180 °C (IEC 60068-3-5); cooling from 180 °C to -40 °C takes 60 min.
- The CO₂ circuit operates at high pressure, so refrigeration-circuit work is restricted to BINDER; the chamber is not field-repairable on the refrigerant side.
Control and operation
- MB2 chamber controller with normal, program and chart-recorder views; fixed-value, timer, time-program and week-program modes with ramp/step setpoints and tolerance ranges.
- Over-temperature protective device class 1 and safety controller class 2.0 (DIN 12880) are standard; an over/under temperature safety device class 2 is optional.
- Options include RS485, zero-voltage switching outputs, analog temperature outputs, flexible Pt 100 object sensor and APT-COM 4 software.
Electrical
- 400 V 3 N/PE 50 Hz variant (Art. 9020-0513): nominal power 5.2 kW, nominal current 8.9 A, unit fuse 16.0 A. A 480 V/60 Hz variant (Art. 9020-0515) also exists.
- IP 20 per EN 60529; supply must be protected by a type B residual current circuit breaker.
Integration & Operating Notes
The chamber may only be operated on a circuit protected by a type B residual current device; a type A or AC RCD in the existing distribution board is not acceptable and must be replaced or supplemented before commissioning.
The 50 Hz variant draws a nominal 8.9 A with 5.2 kW connected load and a 16.0 A unit fuse; the site breaker and cable cross-section must be coordinated with this rather than with the 16 A fuse alone.
Because the refrigerant is CO₂ at up to 120 bar, the installation room volume must be calculated according to EN 378-1:2016+A1:2020 before commissioning; unventilated recesses and damp areas are prohibited and minimum clearances must be kept for heat dispersal.
The chamber temperature must remain below the flash point or sublimation point of the load and no explosive mixture with air may form; verify the material data before setting any program that approaches the 180 °C upper limit.
Maintenance is required at least once a year and an electrical repeat inspection per EN 50678/VDE 0701 and EN 50699/VDE 0702 is required before initial startup, annually, and after any maintenance or repair; refrigeration work must be logged in a service log book.
After 8760 operating hours or two years the controller shows a service message that reappears every two weeks once acknowledged; it can only be reset by BINDER Service, so plan the service visit rather than attempting a controller reset.
Work on the CO₂ circuit may currently only be carried out at BINDER, and any refrigeration maintenance must be performed by personnel trained to EN 13313:2010; on-site repair of the refrigerant side is therefore not an option and a return must be scheduled.
With elevated ambient dust the condenser fan must be cleaned several times a year; inspect the fan grid behind the left maintenance access flap weekly and suction it clean when soiled, and never remove the rear panel or let the chamber become wet.
Selection & Integration Q&A
Pick the MK 240 CO₂ when you need the -50 °C lower limit in a 228 L interior; the standard MK 240 stops at -40 °C. Move to the MK 1020 CO₂ only if the 228 L volume and 30 kg/rack load are insufficient for your specimen batch.
400 V 3 N/PE 50 Hz, 5.2 kW, 8.9 A nominal, 16.0 A unit fuse, and a type B residual current circuit breaker in the site installation; a 480 V/60 Hz variant (Art. 9020-0515) exists for other grids.
Not in unventilated recesses or damp areas; the room volume must be calculated per EN 378-1:2016+A1:2020 for the CO₂ charge, minimum distances must be kept for heat dispersal, and the unit is IP 20 so it must be set up splash-proof.
Annual maintenance, annual electrical repeat inspection per EN 50678/50699, and a service log book are mandatory; RS485, zero-voltage switching outputs, analog temperature outputs, Pt 100 object sensor and APT-COM 4 are options not included in base delivery.