Peter Huber Kältemaschinenbau Minichiller 600 OLÉ Kompakter
Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Minichiller 600 OLÉ Kompakter

Peter Huber Kältemaschinenbau Minichiller 600 OLÉ Kompakter — Recirculating chillers with Noise level 56 dB.

The Minichiller 600 OLÉ Kompakter is a compact recirculating chiller with a pressure/suction pump and OLÉ controller, covering -20 to 40 °C with an 80 °C maximum return temperature. It is distinguished within the Minichiller series by its 600-size cooling capacity and OLÉ interface (USB/RS232), while the 1000-series siblings offer larger capacity. It serves as a point-of-use cooling source for laboratory and industrial circuits requiring stable temperature control.

Noise level
56 dB

Peter Huber Kältemaschinenbau Minichiller Series — Model Comparison & Selection

Model Noise level, dBControllerSafety classTemperature range, °CInterfacePower supply
Minichiller 600 OLÉ Kompakter Current 56OLÉI / NFL-20–40USB (Device), RS232 Inte110-120V 1~ 60Hz
Minichiller 1000 OLÉ Kompakter —OLÉI / NFL-20–40USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 1000w-H Kompakter —Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D208-240V 1~/2~ 50/60Hz
Minichiller 1000w-H OLÉ Kompakter —OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 1000w Kompakter —Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D208-240V 1~/2~ 50/60Hz
Minichiller 1200-H OLÉ Kompakter —OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 1200 OLÉ Kompakter —OLÉI / NFL-20–40USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 1200w-H Kompakter —Pilot ONEIII / FL-20–100——
Minichiller 1200w-H OLÉ Kompakter —OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 280 OLÉ Kompakter 53OLÉI / NFL-5–40USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Minichiller 300 OLÉ Kompakter 53OLÉI / NFL-20–40USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Minichiller 300w-H OLÉ Kompakter 51OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Minichiller 300w OLÉ Kompakter 53OLÉI / NFL-20–40USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Minichiller 600-H OLÉ Kompakter 56OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 600 Kompakter —Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D110-120V 1~ 60Hz
Minichiller 600w OLÉ Kompakter —OLÉI / NFL-20–40USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 800 OLÉ Kompakter —OLÉI / NFL-20–40USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Minichiller 800w-H OLÉ Kompakter —OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz

Full specifications

Core Performance & Functional Specifications
Noise level 56 dB(A)
Maximum delivery flow rate 24 l/min (pressure pump; 0, 7 bar)
suction pump; 0, 4 bar: 18 l/min
Pump connection M16x1 AG male
Pump speed adjustable no
Pump type Pressure- and suction pump
Temperature range -20...40 °C
Dimensions, Weight & Mechanical Design
Weight 36 kg
Electrical, Power & Drive Specifications
Power supply 110-120V 1~ 60Hz
Interfaces, Connections & Control
Controller OLÉ
Display resolution 0, 1 K
Digital interface USB (Device), RS232 Interface
Temperature display OLED Display
Materials, Media & Process Compatibility
Refrigerant R-290 (A3, H220) (1st stage)
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Maximum return flow temperature 80 °C
Protection rating IP20
Standards, Safety & General Data
Safety class I / NFL

Description

Construction and positioning

Performance and media

Installation and operation

Integration & Operating Notes

Mounting
Install drip tray and protect cables below unit

Condensation and thermal fluid can escape from the chiller, so a drip tray must be installed below the unit and any electrical lines directly underneath must be protected against liquid ingress to prevent shock hazard.

Minichiller Operation Manual, pages 15 and 28
Process Limits
Return temperature must not exceed 80 °C

The permissible return-line temperature is 80 °C; exceeding this limit can damage the chiller or trip alarms, so the process heat load returned to the unit must be checked against this value.

Minichiller 600 OLÉ Datasheet, page 2
Electrical
Supply must be 110-120 V/60 Hz with 10 A fuse

The unit draws up to 8.5 A and requires a minimum 10 A fuse; voltage tolerance is ±5% only with simultaneous frequency tolerance of ±2%, and certain combinations are not allowed, so site power quality must be verified before connection.

Minichiller 600 OLÉ Datasheet, page 1
Process Limits
Avoid acetone and polyglycols with plastic pump

The standard plastic pump is not resistant to acetone or polyglycols (depending on manufacturer), so these fluids must be avoided or a more resistant pump specified to prevent premature failure and leaks.

Minichiller 600 OLÉ Datasheet, page 2
Cooling & Media
Use only drinking or filtered river/sea water

Only drinking water or filtered river/sea water may be used as cooling water; sea water must not be used. Anti-corrosion agents are mandatory if salts such as chlorides or bromide are added to the water circuit.

Minichiller Operation Manual, page 28
Maintenance
Fill with minimum 2.8 l heat-transfer fluid

The minimum filling capacity is 2.8 l and the expansion tank is 2.2 l; the heat-transfer fluid volume must be set accordingly, and for freeze protection water should be mixed with glysantine or ethylene glycol.

Minichiller 600 OLÉ Datasheet, pages 1-2
Control & I/O
USB and RS232 available for external control

The OLÉ controller provides USB (Device) and RS232 interfaces for integration with external monitoring or control systems; the OLED display shows temperature with 0.1 K resolution.

Minichiller 600 OLÉ Datasheet, page 1

Selection & Integration Q&A

When should I choose the Minichiller 600 OLÉ over the 1000-series siblings?

Choose the 600 OLÉ when your heat load fits its smaller capacity and you need the OLÉ controller with USB/RS232. The 1000 and 1000-H variants offer higher cooling capacity for larger loads; select those if the 600's capacity is insufficient.

What mating parts and supply are required to connect the Minichiller 600 OLÉ to my application?

The pump connection is M16x1 male; hose connector NW12 and sleeve nuts M16x1 are included, so hoses must match this thread. A 110-120 V 1~ 60 Hz supply with 10 A fuse is required, and a country-specific plug must be specified at ordering.

What are the ambient and installation limits for the Minichiller 600 OLÉ?

Ambient temperature must be 5-40 °C, protection is IP20, and the unit must not be installed in an ATEX zone. A drip tray is required below the unit, and electrical lines underneath must be protected from liquid ingress.

What maintenance and accessories are needed beyond the base delivery?

The base delivery includes hose connector NW12 and sleeve nuts M16x1, but not the heat-transfer fluid; minimum filling is 2.8 l. For freeze protection, mix water with glysantine or ethylene glycol. Anti-corrosion agents are mandatory if salts are added to the water circuit.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Minichiller Operation Manual
Manual ·2,9 МБ ·84 pp.
View PDF
PDF
Minichiller 600 OLÉ
Datasheet ·104,1 КБ ·2 pp.
View PDF