Agilent Technologies Flexible HPLC/UHPLC, Prime Analytical-Scale Purification System
Agilent Technologies Flexible HPLC/UHPLC, Prime Analytical-Scale Purification System — Liquid chromatography.
The Agilent InfinityLab analytical-scale purification system is a flexible HPLC/UHPLC platform configured for 1–3 inch id Load & Lock columns in DAC or SAC mode. It delivers 40,606 N/m plate count at 1 mL/min with 15.18 min retention and 1.27 asymmetry, distinguishing it from fixed-configuration siblings. It serves as the purification bridge between analytical method development and preparative-scale isolation.
Agilent Technologies Preparative HPLC Systems Series — Model Comparison & Selection
Full specifications
| Plate Count | 40606 Nth/meter |
| Retention Time | 15.18 min |
| Typical Flow Rate | 1 mL/min |
| Productivity range mfr | Micrograms Micrograms |
| Asymmetry mfr | 1.27 |
| Column Inner Diameter | 1...3 in |
Description
Construction and series positioning
- The system is built around Agilent Load & Lock columns with inside diameters from 1 to 3 inches (27 to 75 mm), available in both dynamic axial compression (DAC) and static axial compression (SAC) modes.
- Standard stainless steel water jackets are part of the column hardware; mobile packing stations exist for 1, 2 and 3 inch id columns.
- Within the InfinityLab purification portfolio, this analytical-scale modification sits below the 1260/1290 Infinity II Preparative LC Systems and is distinguished from the 1220 Infinity II, 1260 Infinity Bio-Inert, and 1260 Infinity II Manual Preparative siblings by its flexible HPLC/UHPLC prime configuration and 1–3 inch column range.
Behavior under load
- At a typical flow of 1 mL/min the system yields 40,606 plates per meter with a retention time of 15.18 min and asymmetry of 1.27, indicating symmetric peaks at analytical-scale flow.
- The productivity range is expressed in micrograms, consistent with analytical-scale purification rather than gram-scale preparative work.
- No digitized curve points were supplied; load behavior across the 1–3 inch column range must be established empirically per method.
Installation, connection and control
- The brochure digest lists preparative modules including column organizer, column compartment, manual injector, open-bed sampler/collector, detectors, fraction collectors and LC/MSD XT; the specific module set for this configuration is not itemized in the verified facts.
- Column packing requires the matching mobile packing station for the chosen 1, 2 or 3 inch id column; DAC and SAC modes impose different packing procedures.
- Water-jacketed columns require a temperature-control fluid connection; no jacket pressure or flow ratings are provided in the verified facts.
Integration & Operating Notes
The system is specified for Load & Lock columns from 1 to 3 inches id (27 to 75 mm). Fitting a column outside this range invalidates the plate-count and asymmetry performance and may not mate with the packing station or column organizer.
Dynamic axial compression and static axial compression are distinct operating modes for the same column hardware. The packing station and procedure must be selected for the intended mode before the column is installed; switching modes after packing is not described in the verified documentation.
Standard stainless steel water jackets are part of the column construction. A temperature-control fluid circuit must be available at the installation site; the verified facts do not state jacket pressure, flow or temperature ratings, so these must be confirmed against the column datasheet.
Mobile packing stations are offered separately for 1, 2 and 3 inch id columns. Using a station sized for a different id will not correctly pack the column; confirm the station model against the column id before ordering or scheduling packing.
The portfolio includes column organizer, column compartment, manual injector, open-bed sampler/collector, detectors, fraction collectors and LC/MSD XT. The exact modules delivered with this configuration are not itemized in the verified facts; confirm the module list against the order configuration before designing the workflow.
Selection & Integration Q&A
Choose this system when the workflow needs flexible HPLC/UHPLC operation with 1–3 inch id Load & Lock columns in DAC or SAC mode at analytical-scale flow (1 mL/min typical). The 1220 Infinity II is the lower-tier analytical-scale option; the 1260 Infinity II Manual Preparative system targets manual preparative operation rather than this flexible prime configuration.
A mobile packing station sized to the column id (1, 2 or 3 inch) is required for DAC or SAC packing, plus a temperature-control fluid supply for the stainless steel water jackets. Detection and fractionation depend on the selected module set (detectors, fraction collectors, LC/MSD XT); confirm the module list against the order configuration.
Columns must be within the 1–3 inch id range and matched to the correct packing station for their id. DAC and SAC modes use different packing procedures, so the mode must be fixed before packing. The verified facts give no jacket pressure, flow or temperature ratings; confirm these against the column datasheet before installation.
Mobile packing stations for 1, 2 and 3 inch id columns are separate items, as are the preparative columns and supplies listed in the portfolio brochure. Detectors, fraction collectors and LC/MSD XT are modules whose inclusion depends on configuration. The verified facts contain no service-interval schedule; maintenance intervals must be taken from the instrument manual.