Peter Huber Kältemaschinenbau Unimotive 27w
Peter Huber Kältemaschinenbau Unimotive 27w — Temperature control units.
The Unimotive 27w is a water-cooled circulating temperature control unit with a magnetically coupled stainless-steel pump, covering -45 to 95 °C with 24 kW heating capacity. It is the largest of the Unimotive w-series, distinguished by its 35 kW cooling power at 20 °C and 57 A three-phase draw. It serves automotive test benches circulating water-glycol mixtures through external loads.
Peter Huber Kältemaschinenbau Unimotive Series — Model Comparison & Selection
| Model | Display resolution | Heating capacity, W | Power supply | Pump connection | Refrigerant | Safety class |
|---|---|---|---|---|---|---|
| Unimotive 27w Current | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | III / FL |
| Unimotive 10w | 0.01 | 12000 | 400V 3~ 50Hz | M38x1,5 AG male | R-452A (A1, H280) | III / FL |
| Unimotive 10w-XT | 0, 01 | 12000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | I / NFL |
| Unimotive 20w | 0, 01 | 12000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | III / FL |
| Unimotive 20w-XT | 0, 01 | 12000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | I / NFL |
| Unimotive 26w | 0, 01 K | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | III / FL |
| Unimotive 26w-XT | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-452A (A1, H280) | I / NFL |
| Unimotive GL 07w | 0, 01 | 12000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 07w-XT | 0, 01 | 12000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | I / NFL |
| Unimotive GL 10w | 0, 01 | 24000 | 460V 3~ 60Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 10w-XT | 0, 01 | 24000 | 460V 3~ 60Hz | M38x1, 5 AG male | R-744 (A1, H280) | I / NFL |
| Unimotive GL 20w | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 20w-XT | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | I / NFL |
| Unimotive GL 30w | 0, 01 | 24000 | 460V 3~ 60Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 50w | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 50w-XT | 0, 01 | 24000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | I / NFL |
| Unimotive GL 60w | 0, 01 | 48000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | III / FL |
| Unimotive GL 60w-XT | 0, 01 | 48000 | 400V 3~ 50Hz | M38x1, 5 AG male | R-744 (A1, H280) | I / NFL |
Full specifications
| Control output | POKO ONE |
| Heating capacity | 24 kW |
| Pump connection | M38x1, 5 AG male |
| Pump speed adjustable | no |
| Pump type | magnetically coupled, stainless steel |
| External sensor connection | Pt100 |
| Temperature range | -45...95 °C |
| Weight | 456 kg |
| Current consumption | 57 A (max.) |
| Power supply | 400V 3~ 50Hz |
| Controller | Pilot ONE |
| Display resolution | 0, 01 K |
| Digital interface | Ethernet, USB (Host u. Device), RS232 |
| Refrigerant | R-452A (A1, H280) (1st stage) |
| Maximum viscosity | 200 mm²/s |
| Ambient temperature limit | 5...40 °C |
| Cooling water connection | G3/4 male |
| Cooling water consumption | 1530 l/h (at 15°C, flow 0°C) |
| Cooling water differential pressure | 1 bar (min.) |
| Cooling Water Pressure | 6 bar (max.) |
| Protection rating | IP20 |
| Safety class | III / FL |
Description
Construction and series positioning
- Water-cooled refrigeration circuit using R-452A (A1, H280) in the first stage; heat rejection to facility cooling water via G3/4 male connections.
- Magnetically coupled stainless-steel pump, fixed speed (not adjustable), with M38x1.5 male pressure connection.
- Within the Unimotive w-series, the 27w is the largest frame; the 10w and 20w siblings cover lower capacities, and the -XT variants are separate modifications not described here.
- Safety class III / FL; IP20 enclosure, so the unit must be sited in a dry, dust-controlled area.
Thermal behavior and media
- Working range -45 to 95 °C; heating capacity 24 kW.
- Cooling power falls steeply at low temperature: 35 kW at 20 °C down to 2.6 kW at -40 °C, so process heat loads near the cold end must be checked against this curve.
- Intended heat transfer fluid is a water-ethylene glycol mixture with corrosion protection (e.g. Glysantin®) suitable down to -45 °C; maximum permissible kinematic viscosity is 200 mm²/s.
- Cooling water intake must be 5–20 °C; the circuit wetted materials include copper, stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM, which constrains acceptable cooling water chemistry.
Control, connection and operation
- Pilot ONE controller with POKO ONE control output; display resolution 0.01 K; external Pt100 sensor input.
- Interfaces: Ethernet, USB host and device, RS232.
- Electrical supply 400 V 3~ 50 Hz, maximum current 57 A, fusing 3x63 A; delivered with cable but without plug.
- Cooling water consumption 1530 l/h at 15 °C intake with 0 °C flow; minimum differential pressure 1 bar, maximum pressure 6 bar.
- Unit weight 456 kg; a drip tray must be provided below the unit by the responsible body.
Integration & Operating Notes
The unit's leakage current exceeds 3.5 mA, so standard 30 mA residual current devices may nuisance-trip. Earthing and protective-device coordination must be planned by the installing electrician, and the supply must be a socket with protective earth or a hardwired connection made by a certified electrician.
Supply tolerances are ±5% voltage and ±2% frequency, but the combination of -5% voltage with +2% frequency is explicitly not allowed. Verify the actual site supply against this rule before commissioning, since a marginal grid condition can otherwise put the unit outside its permitted operating envelope.
The unit is designed for cooling water intake between 5 °C and 20 °C, with a minimum differential pressure of 1 bar and maximum pressure of 6 bar. Only drinking water or filtered river/sea water is permitted; sea water is prohibited. Pipes must be insulated where surface temperature falls below the condensation point.
Cooling water can flow through the unit even when it is switched off, so the supply must be shut off for shorter downtimes such as overnight. A backflow preventer on the building side is mandatory to protect the drinking water supply, and outdoor siting requires frost-protected lines with cooling water never below 5 °C.
The responsible body must install a condensation water / heat transfer fluid drip tray below the unit. Minimum wall clearances depend on whether the unit is air- or water-cooled and on whether it runs with or without a bath; these clearances govern energy dissipation and must be respected to avoid overheating.
The unit must not be installed or started inside an ATEX zone. It is a Group 1 Class A device per EN55011, intended for industrial EMC environments, so it may not be EMC-compatible in residential or light-industrial settings. Refrigerant charge and room size must be checked during installation to avoid dangerous refrigerant concentration.
For pressure-sensitive applications such as glass reactors, the maximum flow pressure of the unit must be taken into account and an external bypass may be required. Hose inside diameters must at least match the M38x1.5 pump connections, with larger diameters for longer lines to limit pressure drop.
The heat transfer fluid must always be adjusted to room temperature before switching off to avoid overpressure in the system. This applies at the end of every test cycle and before maintenance or draining, and protects both the unit and the connected application from pressure damage.
Selection & Integration Q&A
Pick the 27w when the load needs up to 24 kW heating and high cooling power at moderate temperatures (35 kW at 20 °C), accepting 57 A three-phase draw and 456 kg. The 10w and 20w cover lower capacities; the -XT variants are separate modifications, not substitutes for this frame.
Cooling water at 5–20 °C, 1–4 bar differential (max 6 bar), G3/4 male connections, 1530 l/h at 15 °C intake, with a building-side backflow preventer. Power is 400 V 3~ 50 Hz, 57 A max, 3x63 A fusing; cable supplied without plug, and leakage current above 3.5 mA affects RCD choice.
Indoors in a dry area, 5–40 °C ambient, IP20, never in an ATEX zone; it is Group 1 Class A EMC equipment for industrial environments. A drip tray below the unit is mandatory, wall clearances per the manual apply, and refrigerant charge versus room size must be checked.
The three-phase cable is supplied without a plug, so a suitable plug or hardwired connection by a certified electrician is needed. Mating pump fittings (ball socket per DIN 3863, sleeve nut per DIN 3870) and the drip tray are not part of the unit. Cooling water must be shut off during downtimes.