Peter Huber Kältemaschinenbau Unimotive GL 10w-XT
Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Unimotive GL 10w-XT

Peter Huber Kältemaschinenbau Unimotive GL 10w-XT — Temperature control units.

The Unimotive GL 10w-XT is a water-cooled, magnetically coupled stainless-steel pump temperature control unit for water-ethylene glycol mixtures down to -45 °C and up to 150 °C, rated 24 kW heating on a 460 V 3~ 60 Hz supply. It is the extended-temperature (XT) variant of the 10w platform, distinguished from the 20w siblings by its smaller capacity class. It serves automotive test benches and process loops requiring sub-zero glycol temperature control with Pilot ONE regulation.

Peter Huber Kältemaschinenbau Unimotive Series — Model Comparison & Selection

Model Display resolutionHeating capacity, WPower supplyPump connectionRefrigerantSafety class
Unimotive GL 10w-XT Current 0, 0124000460V 3~ 60HzM38x1, 5 AG maleR-744 (A1, H280)I / NFL
Unimotive 10w 0.0112000400V 3~ 50HzM38x1,5 AG maleR-452A (A1, H280)III / FL
Unimotive 10w-XT 0, 0112000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)I / NFL
Unimotive 20w 0, 0112000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)III / FL
Unimotive 20w-XT 0, 0112000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)I / NFL
Unimotive 26w 0, 01 K24000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)III / FL
Unimotive 26w-XT 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)I / NFL
Unimotive 27w 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-452A (A1, H280)III / FL
Unimotive GL 07w 0, 0112000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 07w-XT 0, 0112000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)I / NFL
Unimotive GL 10w 0, 0124000460V 3~ 60HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 20w 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 20w-XT 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)I / NFL
Unimotive GL 30w 0, 0124000460V 3~ 60HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 50w 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 50w-XT 0, 0124000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)I / NFL
Unimotive GL 60w 0, 0148000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)III / FL
Unimotive GL 60w-XT 0, 0148000400V 3~ 50HzM38x1, 5 AG maleR-744 (A1, H280)I / NFL

Full specifications

Core Performance & Functional Specifications
Control output POKO ONE
Heating capacity 24 kW
Pump connection M38x1, 5 AG male
Pump speed adjustable no
Pump type magnetically coupled, stainless steel
External sensor connection Pt100
Temperature range -45...150 °C
Dimensions, Weight & Mechanical Design
Weight 600 kg
Electrical, Power & Drive Specifications
Current consumption 47 A (max)
Power supply 460V 3~ 60Hz
Interfaces, Connections & Control
Controller Pilot ONE
Display resolution 0, 01 K
Digital interface Ethernet, USB (Host u. Device), RS232
Materials, Media & Process Compatibility
Refrigerant R-744 (A1, H280) (1st stage)
Maximum viscosity 200 mm²/s
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Cooling water connection G3/4 male
Cooling water consumption 2100 l/h (at 15°C, flow 0°C)
Cooling water differential pressure 1 bar (min)
Cooling Water Pressure 6 bar (max)
Protection rating IP20
Standards, Safety & General Data
Safety class I / NFL

Description

Construction and series positioning

Working range and media behavior

Installation, control and operation

Integration & Operating Notes

Electrical
Provide a UL 489 branch breaker and a site disconnect

The 460 V 3~ 60 Hz unit draws up to 47 A and requires 3x63A fusing with external branch circuit protection according to UL 489. Because three-phase devices under 63 A are delivered with cable but without a plug, the installer must supply a matching receptacle or hardwired disconnect; hardwiring must be performed by a certified electrician.

Datasheet, Specifications; Operation Manual, Section Electrical Connection
Electrical
Do not combine -5% voltage with +2% frequency

Voltage tolerance is ±5% and frequency tolerance ±2%, but the datasheet explicitly forbids the unfavorable combination (e.g. -5% voltage together with +2% frequency). Verify the actual site supply envelope before ordering, since a supply at the edge of both bands simultaneously is outside the permitted operating window.

Datasheet, Specifications
Cooling & Media
Cooling water 5...20 °C, 1...4 bar differential, 6 bar max

The cooling water intake must stay between 5 °C and 20 °C, with a minimum differential pressure of 1 bar and a maximum supply pressure of 6 bar. Consumption is 2100 l/h at 15 °C cooling water with 0 °C flow temperature; higher cooling water temperatures reduce cooling power and may increase required flow, so the site loop must be sized with margin.

Datasheet, Specifications
Cooling & Media
Use only drinking or filtered water, never sea water

The cooling water circuit contains copper, stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM. Only drinking water or filtered river/sea water is permitted, and sea water is explicitly prohibited. A building-side backflow preventer is required to protect the drinking water supply, and cooling water must be shut off during downtimes because flow can occur even with the unit switched off.

Operation Manual, Section Cooling Water Connection
Process Limits
Fluid must be water-glycol with viscosity below 200 mm²/s

The unit is constructed for water-ethylene glycol mixtures with corrosion protection down to -45 °C. The maximum permissible kinematic viscosity is 200 mm²/s, which limits how cold and how concentrated the mixture may be at the pump. Other fluid families are not covered by the datasheet and should not be assumed compatible with the stainless-steel magnetic pump and EPDM seals.

Datasheet, Overview and Specifications
Mounting
Install a drip tray and respect wall clearances

The responsible body must install a condensation water/heat transfer fluid drip tray below the unit. Minimum wall clearances depend on whether the unit is air- or water-cooled and on operation with or without a bath; insufficient clearance prevents adequate energy dissipation. The 600 kg weight also requires a load-rated floor at the installation point.

Operation Manual, Section Installation
Mounting
No ATEX zone; check refrigerant charge against room volume

The unit must not be installed or started inside an ATEX zone. Because the refrigerant is R-744 (A1, H280) with a 3.3 kg charge, the room size must be checked against the charge during installation to avoid dangerous refrigerant concentration. The unit is Group 1 Class A (EN 55011) and is intended for industrial EMC environments only.

Operation Manual, Sections Installation and EMC
Process Limits
Bring fluid to room temperature before switching off

The heat transfer fluid must always be adjusted to room temperature before switching off to avoid overpressure in the system. For pressure-sensitive applications such as glass reactors, the maximum flow pressure of the unit must be taken into account and an external bypass may be needed. Hose inside diameters must at least match the M38x1.5 pump connections, with larger diameters for longer lines.

Operation Manual, Section Normal Operation
Maintenance
Plan an 8.9 l minimum fill and 19.9 l expansion volume

Commissioning requires a minimum filling capacity of 8.9 l with a 19.9 l expansion tank, so the fluid charge and expansion allowance must be planned before start-up. Cooling water lines must be frost-protected if the unit is sited outdoors, and the cooling water temperature must never fall below 5 °C.

Datasheet, Specifications; Operation Manual, Section Commissioning

Selection & Integration Q&A

When should I choose the GL 10w-XT rather than a 20w or non-XT Unimotive sibling?

Pick the 10w-XT when the duty fits the smaller 10w capacity class but the process needs the extended -45...150 °C range with water-glycol. Move to a 20w sibling when heating/cooling demand exceeds the 24 kW heating class; the non-XT 10w if the extended cold end is not required.

What must the site provide for power and cooling water to integrate this unit?

A 460 V 3~ 60 Hz supply at 47 A max with 3x63A fusing and a UL 489 breaker plus a site disconnect (no plug shipped). Cooling water at 5...20 °C, 1...4 bar differential, 6 bar max, 2100 l/h at 15 °C, with a backflow preventer and a drip tray.

What environment and duty-cycle limits apply to installation?

Indoor, non-ATEX, 5...40 °C ambient, IP20, Group 1 Class A EMC environment. Respect wall clearances for energy dissipation, check R-744 charge against room volume, and shut off cooling water during downtimes since flow can occur with the unit off.

What is not included in base delivery and what must be procured for commissioning?

No plug for the 460 V three-phase cable, no UL 489 breaker, no drip tray, no backflow preventer, and no M38x1.5 pump fittings or G3/4 cooling water hoses. The heat transfer fluid (water-glycol with corrosion protection) and the minimum 8.9 l charge are also site-supplied.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Unimotive GL 10w-XT
Datasheet ·97,0 КБ ·2 pp.
View PDF
PDF
Unimotive Operation Manual
Manual ·2,8 МБ ·82 pp.
View PDF