No photo available yet

Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Unistat T330w HT Dynamisches

Peter Huber Kältemaschinenbau Unistat T330w HT Dynamisches — Temperature control units.

The Unistat T330w HT is a water-cooled, dynamically temperature-controlled unit with a 24 kW heater and a 65–300 °C range (15–300 °C with water cooling), using a magnetically coupled stainless-steel pump. It has no active refrigeration, so sub-65 °C operation depends on process heat loss or cooling water. It serves high-temperature process loops requiring precise, fast temperature control.

Peter Huber Kältemaschinenbau Unistate Bis 425C Series — Model Comparison & Selection

Model Display resolutionPower supplyPump connectionPump typeTemperature range, °CExpansion volume, m³
Unistat T330w HT Dynamisches Current 0, 01 K400V 3~ 50HzM30x1, 5 AG malemagnetically coupled, st65–3000.024
Chili Dynamisches 0.01200-240V 1~/2~ 50/60HzM24x1,5 AG malePressure pump, variable 65–3000.002
Unistat T305 Dynamisches 0, 01200-240V 1~/2~ 50/60HzM24x1, 5 AG malePressure pump, variable 65–300—
Unistat T305 HT Dynamisches 0, 01200-240V 1~/2~ 50/60HzM24x1, 5 AG malePressure pump, variable 65–300—
Unistat T305w HT Dynamisches 0, 01200-240V 1~/2~ 50/60HzM24x1, 5 AG malePressure pump, variable 65–300—
Unistat T320 Dynamisches 0, 01460V 3~ 60HzM30x1, 5 AG malemagnetically coupled, st65–3000.024
Unistat T320w HT Dynamisches 0, 01400V 3~ 50HzM30x1, 5 AG malemagnetically coupled, st65–3000.024
Unistat T330 HT Dynamisches 0, 01400V 3~ 50HzM30x1, 5 AG malemagnetically coupled, st65–3000.024
Unistat T340 Dynamisches 0, 01460V 3~ 60HzM38x1, 5 AG malemagnetically coupled, st65–3000.056
Unistat T340 HT Dynamisches 0, 01400V 3~ 50HzM38x1, 5 AG malemagnetically coupled, st65–3000.056
Unistat T345 Dynamisches 0, 01400V 3~ 50HzM38x1, 5 AG malemagnetically coupled, st65–3000.056
Unistat T345 HT Dynamisches 0, 01400V 3~ 50HzM38x1, 5 AG malemagnetically coupled, st65–3000.056
Unistat T350 HT Dynamisches 0, 01400V 3~ 50HzM38x1, 5 AG malemagnetically coupled, st65–3000.056
Unistat T402 Dynamisches 0, 01400V 3~N 50/60HzM24x1, 5 AG malePressure pump, variable 80–425—
Unistat TR401 Dynamisches 0, 01200-240V 1~/2~ 50/60HzM24x1, 5 (Flow) M24x1, 5Pressure pump, variable 50–4000.005
Unistat TR402 Dynamisches 0, 01200-240V 1~/2~ 50/60HzM24x1, 5 (Flow) M24x1, 5Pressure pump, variable 80–425—

Full specifications

Core Performance & Functional Specifications
Control output POKO ONE
Expansion volume 24 l
Filling volume 7 l (min)
Heating capacity 24 kW
Pump connection M30x1, 5 AG male
Pump speed adjustable Yes
Pump type magnetically coupled, stainless steel
External sensor connection Pt100
Temperature range 65...300 °C
with water cooling: 15...300 °C
Electrical, Power & Drive Specifications
Power supply 400V 3~ 50Hz
Interfaces, Connections & Control
Controller Pilot ONE
Display resolution 0, 01 K
Digital interface Ethernet, USB (Host u. Device), RS232
Materials, Media & Process Compatibility
Maximum viscosity 50 mm²/s
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Cooling water connection G3/4 male
Cooling water differential pressure 1 bar (min)
Cooling Water Pressure 6 bar (max)
Protection rating IP20
Standards, Safety & General Data
Safety class III / FL

Description

Construction and series positioning

The Unistat T330w HT is a water-cooled high-temperature variant in the Unistat T3xx series. Unlike the T305/T305 HT siblings, it provides 24 kW heating capacity and a 65–300 °C range (15–300 °C with water cooling). The 'w' denotes water cooling; the 'HT' denotes high-temperature capability. The unit uses a magnetically coupled stainless-steel pump with adjustable speed, a Pilot ONE controller with POKO ONE control output, and a Pt100 external sensor input. It has no active refrigeration system, so it cannot actively cool below 65 °C without water cooling or sufficient process heat loss.

Behavior under load and media

Heating capacity is 24 kW. The temperature range is 65–300 °C without water cooling and 15–300 °C with water cooling. Cooling power decreases as cooling water temperature rises, and the required cooling water flow rate may increase. The cooling water exit temperature is limited to 55 °C, and no steam exits when cooling with circulation temperatures over 100 °C. The maximum permissible kinematic viscosity of the thermofluid is 50 mm²/s. The expansion tank capacity is 24 l, and the minimum filling capacity is 7 l.

Installation, connection and control

Cooling water connection is G3/4 male, requiring a minimum differential pressure of 1 bar and maximum pressure of 6 bar; supply temperature must be 5–20 °C, and pipes must be insulated if condensation is possible. Pump connection is M30x1.5 male, requiring ball socket per DIN 3863 and sleeve nut per DIN 3870. Power supply is 400 V 3~ 50 Hz; three-phase devices under 63 A are supplied with cable but without a plug. Leakage current exceeds 3.5 mA. Protection rating is IP20; ambient temperature must be 5–40 °C. The unit must not be installed in an ATEX zone. Transport and store upright only; move only when emptied. Allow about 2 hours acclimation after temperature changes before power-on. For externally closed applications, the expansion vessel must remain unlocked; for externally open applications, it must be locked. Hard-wired power connection must be done by an electrician. Interfaces include Ethernet, USB (Host and Device), and RS232. The controller supports Process Safety mode (requires compressor set to Permanently ON) and Power Failure Auto (resumes temperature control after power outage if active). Shut off cooling water supply even for short downtimes.

Integration & Operating Notes

Process Limits
No active refrigeration below 65 °C without water cooling

The unit cannot actively cool below 65 °C. To reach temperatures down to 15 °C, water cooling must be connected and operating, or the application must provide sufficient heat loss. Exceeding this limit without cooling water risks invalid results or unit damage.

Datasheet, page 2, selection
Cooling & Media
Cooling water must be 5–20 °C and insulated if below dew point

Cooling water supply temperature must be between 5 °C and 20 °C. If the water temperature can drop below the ambient dew point, internal cooling water pipes must be insulated to prevent condensation. Cooling water pressure must be 1–6 bar differential.

Datasheet, page 2, installation
Electrical
Leakage current >3.5 mA requires RCD selection per local code

The unit's leakage current exceeds 3.5 mA. Protective earth and residual current device (RCD) selection must account for this to ensure electrical safety and compliance with local installation codes.

Datasheet, page 2, safety
Electrical
Three-phase units under 63 A supplied without plug

Devices with current consumption less than 63 A are delivered with a cable but no plug. The customer must provide a suitable plug and have the connection made by an electrician. Supply voltage and frequency must match the rating plate.

Datasheet, page 2, installation; Manual, page 37
Mounting
Never install or start in an ATEX zone

The unit must not be installed or started inside an ATEX zone. Explosion protection requires an Ex px cabinet. Ignoring this creates an immediate ignition hazard.

Operation Manual, page 15, safety
Mounting
Transport upright and only when emptied

Transport and store the unit upright only; horizontal transport damages the compressor. Move only an emptied unit to avoid thermal fluid overflow. Casters are not for transport and carry only 25% of total mass symmetrically; use an industrial truck.

Operation Manual, page 22, installation
Process Limits
Expansion vessel lock depends on open or closed application

For externally closed applications, the expansion vessel must remain unlocked; locking it causes overpressure damage. For externally open applications, the expansion vessel must be locked to prevent fluid loss.

Operation Manual, page 33, installation
Control & I/O
Process Safety mode requires compressor set to Permanently ON

When using Process Safety mode, the compressor must be set to Permanently ON to keep cooling active at the over-temperature trigger. This ensures cooling remains available for exothermic process protection.

Operation Manual, page 19, operation
Control & I/O
Power Failure Auto resumes control automatically after outage

If temperature control is active during a power outage, the process will automatically continue after the power outage when Power Failure Auto is enabled. Assess unattended operation risks accordingly.

Operation Manual, page 20, operation
Maintenance
Shut off cooling water even for overnight downtimes

Shut off the cooling water supply to the unit even for shorter downtimes such as overnight. This prevents water damage and unnecessary load on the cooling water circuit.

Operation Manual, page 29, maintenance
Maintenance
Periodically check hoses and connections for leaks and quality

Hoses and hose connections must be checked periodically for leaks and quality, and replaced as needed. This preventive maintenance avoids fluid loss and ensures safe operation.

Operation Manual, page 29, maintenance

Selection & Integration Q&A

When should I choose the Unistat T330w HT over the T305w HT or T305 HT siblings?

Choose the T330w HT when you need 24 kW heating and a 65–300 °C range (15–300 °C with water cooling) for high-temperature processes. The T305 variants have lower heating capacity; select them for smaller loads or lower temperature requirements.

What are the requirements for the cooling water supply and pump connection?

Cooling water: G3/4 male, 5–20 °C, 1–6 bar differential pressure. Pump: M30x1.5 male, requiring ball socket per DIN 3863 and sleeve nut per DIN 3870. Insulate cooling water pipes if below dew point.

What maintenance is required and what accessories are not included?

Periodically check hoses and connections for leaks and quality; replace as needed. Shut off cooling water even overnight. A power plug is not included for three-phase units under 63 A; customer must provide. No other consumables specified.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Unistat T330w HT Technical Data
Datasheet ·18,6 КБ ·2 pp.
View PDF
PDF
Unistat Operation Manual
Manual ·3,7 МБ ·102 pp.
View PDF