Elmo Rietschle 2BH1430
Elmo Rietschle 2BH1430 — Side-Channel / Regenerative Ring Blowers with Max. differential pressure 100 mbar, Motor power 0.95 kW, Noise level 61 dB.
The 2BH1430 is a side-channel blower from the G-BH1 series, driven by a 1.60 kW IE3/NP motor for 60 Hz operation (230 YY / 460 Y) and 1.30 kW for 50 Hz (190–210 V). It delivers a maximum differential pressure of -190 mbar in vacuum and 170 mbar in pressure at 60 Hz, with continuous operation permitted across the entire performance curve. This modification is positioned as a mid-range unit within the series, suited for pneumatic conveying, suction holding, or aeration duties where a compact, UL/CSA-approved blower is required.
Elmo Rietschle G-BH1 Series — Model Comparison & Selection
| Model | Motor power, kW | Noise level, dB | Weight, kg | Max. differential pressure, mbar | Current, A | Protection rating |
|---|---|---|---|---|---|---|
| 2BH1430 Current | 1.1 | 64 | 16 | 110 | 4.2 | IP55 |
| 2BH1009 | — | — | — | — | — | — |
| 2BH1014 | 0.32 | 57 | 11 | -55 | 3.2–6.5 | IP55 |
| 2BH1015 | 1.3 | 64 | 21 | -180 | 8–16 | IP55 |
| 2BH1023 | 1.75 | 69 | 69 | -190 | 10–20 | IP55 |
| 2BH1035 | 2.2 | 64 | 70 | -140 | 14.3–27 | IP55 |
| 2BH1100 | 0.2 | 53 | 10 | -120 | 1.39 Δ / 0.80 Y | IP 55 |
| 2BH1200 | 0.29 | 40 | 57 | -40 | 1.38 0.8 Y | IP55 |
| 2BH1300 | 0.29 | 100 | 51 | -100 | 1.9 | IP 55 |
| 2BH1310 | 0.7 | 56 | 16 | -250 | 3.8 Δ / 2.20 Y | IP55 |
| 2BH1330 | 0.29 | 80 | 51 | — | 1.74 Δ / 1.0 Y | IP55 |
| 2BH1400 | 0.95 | 61 | 16 | -180 | 5.6 | IP55 |
| 2BH1410 | 2 | 65 | 28 | -300 | 6.9 | IP55 |
| 2BH1490 | 0.95 | 61 | 16 | -140 | 4.8 VV | IP55 |
| 2BH1500 | 0.95 | 65 | 21 | -90 | 4.2 | IP55 |
| 2BH1510 | 4 | 71 | 48 | -400 | 7.6–15.2 | IP55 |
| 2BH1530 | 1.6 | 69 | 25 | -90 | 4.7 | IP55 |
| 2BH1590 | 1.3 | 61 | 21 | -190 | 2.75 | IP55 |
| 2BH1600 | 1.75 | 72 | 31 | 130 | 9.9 | IP55 |
| 2BH1610 | 2.5 | 75 | 48 | 160 | 6 | IP55 |
| 2BH1630 | 2.5 | 64 | 36 | -160 | 17.1 | IP55 |
| 2BH1640 | 4.6 | 65 | 65 | -240–260 | 17.1 | IP55 |
| 2BH1690 | 2.5 | 64 | 34 | -200 | 9.9 | IP55 |
| 2BH1800 | 5.8 | 77 | 131 | 260 | 11–22 | IP55 |
| 2BH1810 | 9.9 | 74 | 188 | -460 | 30.8 | IP55 |
| 2BH1830 | 5.8 | 75 | 133 | -160 | 19.4 | IP55 |
| 2BH1900 | 8.6 | 71 | 183 | -190 | 30.8 | IP55 |
| 2BH1910 | 12.6 | 76 | 295 | -220 | 26.4 | IP55 |
| 2BH1930 | 8.6 | 75 | 212 | -80 | 17.6–35.2 | IP55 |
| 2BH1940 | 19.9 | 73 | 303 | -150 | 63.1 | IP55 |
| 2BH1943 | 17.3 | 77 | 330 | -160 | 72.2 UU / 36.1 U | IP55 |
Full specifications
| Max. differential pressure | 110 mbar (50 Hz) 60 Hz: 100 mbar |
| Motor power | 0.95 kW (50 Hz) 60 Hz: 1.10 kW |
| Noise level | 61 dB (50 Hz) 60 Hz: 64 dB |
| Series mfr | G-BH 1 N |
| Product type mfr | Side channel blower with IE3-motors |
| Operation modes mfr | Vacuum pump and compressor, continuous operation |
| Approvals mfr | UL and CSA approved; UL 1450 and CAN/CSA C22.2 N |
| Performance curve basis mfr | Air at 15 °C and atmospheric pressure 1013 mbar, |
| Total pressure difference validity mfr | Suction and ambient temperature up to 25 °C |
| Type No. mfr | 2BH1430-0AK26 |
| Max. differential pressure Vacuum mfr | -190 mbar (60 Hz) |
| Max. differential pressure Vacuum mfr | -100 mbar (50 Hz) |
| Vacuum mfr | -110 mbar (50 Hz) |
| Vacuum mfr | -100 mbar (60 Hz) |
| Order No. mfr | 2BH1430-0AK11 (50/60 Hz) |
| Approval mfr | UL 1450 and CAN/CSA C22.2 No. 68-09 (certificate |
| Weight | 16 kg |
| Number of stages | 1 |
| Current | 4.2 A (50 Hz) 60 Hz: 4.8 / 2.4 A |
| Frequency | 50/60 Hz |
| Power supply | 3~ 50/60 Hz |
| Voltage | 190-210 V (50 Hz) 60 Hz: 190-210 / 380-420 V |
| Voltage tolerance (three phase motors) mfr | ±10 % |
| Frequency tolerance mfr | ±2 % |
| Efficiency class mfr | NP (60 Hz) |
| Efficiency class mfr | IE3 (50 Hz) |
| Voltage tolerance mfr | +/-10 % (three phase motors) |
| Frequency tolerance mfr | +/- 2 % (maximum) |
| Voltage (alt 60 Hz) mfr | 200 V (60 Hz) |
| Protection rating | IP55 |
| Sound pressure level mfr | 64 dB(A) (60 Hz) |
| Sound pressure level mfr | 61 dB(A) (50 Hz) |
| Sound pres. Level mfr | 61 dB(A) (50 Hz) |
| Sound pres. Level mfr | 64 dB(A) (60 Hz) |
| Converter input voltage suitability (standard motor insulation) mfr | up to 500 V |
| Motor efficiency standard mfr | NEMA MG1-12; NP=NEMA Premium; NEMA Premium inclu |
Description
Construction and series positioning
- The 2BH1430 is a side-channel (regenerative) blower with an IE3/NEMA Premium motor, IP55 protection, and insulation class F. It is part of the G-BH 1 N series, which includes smaller siblings such as the 2BH1009, 2BH1014, 2BH1015, and 2BH1023. The 2BH1430 offers higher power and pressure capability than these smaller models, making it the choice when the duty point requires up to 190 mbar vacuum or 170 mbar pressure at 60 Hz.
- The motor is approved to UL 1450 and CAN/CSA C22.2 No. 68-09 (certificate E225239), and the blower is suitable for continuous operation in both vacuum and compressor modes.
Behavior under load and media
- Performance curves are based on air at 15 °C and 1013 mbar, with a tolerance of ±10%. The total pressure difference is valid for suction and ambient temperatures up to 25 °C. At 60 Hz, the maximum differential pressure is -190 mbar (vacuum) and 170 mbar (pressure); at 50 Hz, these values reduce to -100 mbar and 100 mbar respectively. The blower can be operated continuously over the entire curve range, but the actual achievable pressure depends on the inlet air temperature and the system's resistance.
- The sound pressure level is 64 dB(A) at 60 Hz and 61 dB(A) at 50 Hz, measured under standard conditions. No curve points are provided, so the engineer must refer to the published performance curve for the specific model to determine flow at a given pressure.
Installation, connection, and control
- The motor is designed for three-phase supply with a voltage tolerance of ±10% and frequency tolerance of ±2%. It can be connected to a converter with input voltage up to 500 V when using standard motor insulation. The terminal box allows connection for 230 V (YY) or 460 V (Y) at 60 Hz, and 190–210 V at 50 Hz. The blower is not supplied with a built-in overload protection; external motor protection must be provided according to the motor current (5.5 A at 60 Hz, 5.6 A at 50 Hz).
- The blower is typically mounted horizontally, but the installation manual should be consulted for orientation and clearance requirements. The IP55 rating allows operation in dusty and humid environments, but the motor cooling air must be clean and unobstructed. The blower can be used as either a vacuum pump or a compressor; the direction of rotation determines the mode, and the suction and discharge ports must be connected accordingly.
Integration & Operating Notes
The blower motor does not include internal thermal protection. The engineer must install a contactor or overload relay set to the rated current (5.5 A at 60 Hz, 5.6 A at 50 Hz) to prevent winding damage from overload or phase loss. The UL/CSA approval covers the motor only when protected according to the manual.
The published maximum differential pressures (-190 mbar vacuum, 170 mbar pressure at 60 Hz) are based on air at 15 °C and are valid only when suction and ambient temperatures do not exceed 25 °C. Higher temperatures reduce the achievable pressure and may cause motor overload due to reduced air density. For hot gas applications, derate the blower or consult the manufacturer.
The IP55 motor relies on free convection over its fins. Install the blower with the motor axis horizontal and provide at least 100 mm clearance around the cooling air inlet and outlet. Avoid recirculation of hot discharge air into the motor cooling intake, which can cause overheating. Secure the blower to a rigid base to minimize vibration.
The blower uses grease-lubricated bearings and contact seals. Under normal operating conditions, inspect bearings every 10,000 hours and replace if noise or vibration increases. Check the seal between the impeller and housing for wear if performance drops. Keep the cooling fins clean to maintain heat dissipation.
Selection & Integration Q&A
Choose the 2BH1430 when your duty point requires up to 190 mbar vacuum or 170 mbar pressure at 60 Hz, or when the higher 1.6 kW power is needed for a given flow. The smaller siblings like 2BH1023 deliver lower maximum pressure and are better suited for lower-demand applications, saving space and energy.
The motor can be connected to a 3-phase supply with ±10% voltage tolerance and ±2% frequency tolerance. For converter operation, input voltage must not exceed 500 V with standard insulation. Use a motor overload relay set to 5.5 A (60 Hz) or 5.6 A (50 Hz). Ensure the supply can handle the starting current, which may be several times the rated current.
The blower is rated for continuous operation over the entire performance curve, but the maximum differential pressure is valid only when suction and ambient temperatures are up to 25 °C. Above this, derate the pressure or reduce the duty cycle to avoid motor overheating. The IP55 rating allows dusty or humid environments, but cooling air must be clean.
The base delivery includes the blower only. You must provide motor protection (contactor/overload), electrical cables, and mating flanges for suction and discharge ports. No spare parts, filters, or silencers are included. Periodic maintenance includes bearing inspection every 10,000 hours and seal replacement if performance degrades.