Peter Huber Kältemaschinenbau Unichiller P010 OLÉ
Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Unichiller P010 OLÉ

Peter Huber Kältemaschinenbau Unichiller P010 OLÉ — Recirculating chillers with Noise level 57 dB.

The Unichiller P010 OLÉ is an air-cooled, CFC/HCFC-free recirculating chiller with a plastic pump and G3/4 male connections, rated for -20 to 40 °C. Its 'P' designation targets high-pressure-drop circuits, where flow falls from 21 l/min at 0.5 bar to 6 l/min at 2.0 bar. It serves closed-loop process cooling with the OLÉ controller and USB/RS232 interfaces.

Noise level
57 dB

Peter Huber Kältemaschinenbau Unichiller Series — Model Comparison & Selection

Model Noise level, dBControllerSafety classTemperature range, °CInterfacePower supply
Unichiller P010 OLÉ Current 57OLÉI / NFL-20–40USB (Device), RS232 Inte110-120V 1~ 50/60Hz
Unichiller 015 63Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 015-H 63Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~/2~ 50Hz
Unichiller 015-H OLÉ 63OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 015w-H 54Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 015w-H OLÉ 54OLÉI / NFL-20–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 017T 64Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 017T-H 64Pilot ONEI / NFL-10–100Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 017Tw-H 64Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D208V 2~ 60Hz
Unichiller 020T —Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 020T-H —Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D208V 2~ 60Hz
Unichiller 020Tw 60Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 020Tw-H 60Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 022-H 65Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 022-H OLÉ 65OLÉI / NFL-10–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 022 OLÉ 65OLÉI / NFL-10–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 022w 60Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 022w-H —Pilot ONEIII / FL-10–100——
Unichiller 022w OLÉ 60OLÉI / NFL-10–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 025-H 64Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 025-H OLÉ 64OLÉIII / FL-10–100USB (Device), RS232 Inte208-230V 1~/2~ 60Hz
Unichiller 025 OLÉ 64OLÉI / NFL-10–40USB (Device), RS232 Inte208-230V 1~/2~ 60Hz
Unichiller 025T 74Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 025T-H 74Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 025Tw-H —Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D230V 1~ 50Hz
Unichiller 025w 60Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller 025w-H OLÉ 60OLÉIII / FL-10–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller 025w OLÉ 60OLÉI / NFL-10–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P007 58Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D208-240V 1~/2~ 50/60Hz
Unichiller P007-H —Pilot ONEIII / FL-20–100——
Unichiller P007-H OLÉ 58OLÉIII / FL-20–100USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Unichiller P007 OLÉ 58OLÉI / NFL-20–40USB (Device), RS232 Inte208-240V 1~/2~ 50/60Hz
Unichiller P010 57Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D208V 2~ 60Hz
Unichiller P010-H 57Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~/2~ 50/60Hz
Unichiller P010-H OLÉ 57OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Unichiller P010w —Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D220-240V 1~/2~ 50/60Hz
Unichiller P010w-H —Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~/2~ 50/60Hz
Unichiller P012 59Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D208V 2~ 60Hz
Unichiller P012-H 59Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~/2~ 50/60Hz
Unichiller P012-H OLÉ 59OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Unichiller P012 OLÉ 59OLÉI / NFL-20–40USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Unichiller P012w-H —Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~/2~ 50/60Hz
Unichiller P012w-H OLÉ —OLÉIII / FL-20–100USB (Device), RS232 Inte208V 2~ 60Hz
Unichiller P012w OLÉ —OLÉI / NFL-20–40USB (Device), RS232 Inte220-240V 1~/2~ 50/60Hz
Unichiller P015 63Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D220-240V 1~/2~ 50Hz
Unichiller P015-H 63Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P015-H OLÉ 63OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P015 OLÉ 63OLÉI / NFL-20–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P015w 54Pilot ONEI / NFL-20–40Ethernet, USB (Host u. D220-240V 1~/2~ 50Hz
Unichiller P015w-H 54Pilot ONEIII / FL-20–100Ethernet, USB (Host u. D208-230V 1~/2~ 60Hz
Unichiller P015w-H OLÉ 54OLÉIII / FL-20–100USB (Device), RS232 Inte220-240V 1~/2~ 50Hz
Unichiller P022 65Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P022-H 65Pilot ONEI / NFL-10–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P022-H OLÉ 65OLÉI / NFL-10–100USB (Device), RS232 Inte208-230V 1~/2~ 60Hz
Unichiller P022 OLÉ 65OLÉI / NFL-10–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P022w 60Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D208-230V 1~/2~ 60Hz
Unichiller P022w-H 60Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P022w OLÉ 60OLÉI / NFL-10–40USB (Device), RS232 Inte208-230V 1~/2~ 60Hz
Unichiller P025 64Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P025-H 64Pilot ONEIII / FL-10–100Ethernet, USB (Host u. D220-240V 1~ 50Hz
Unichiller P025-H OLÉ 64OLÉIII / FL-10–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P025 OLÉ 64OLÉI / NFL-10–40USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P025w 60Pilot ONEI / NFL-10–40Ethernet, USB (Host u. D208-230V 1~/2~ 60Hz
Unichiller P025w-H OLÉ 60OLÉIII / FL-10–100USB (Device), RS232 Inte220-240V 1~ 50Hz
Unichiller P025w OLÉ 60OLÉI / NFL-10–40USB (Device), RS232 Inte208-230V 1~/2~ 60Hz

Full specifications

Core Performance & Functional Specifications
Noise level 57 dB(A)
Pump connection G3/4 AG male
Pump speed adjustable no
Pump type B
Temperature range -20...40 °C
Dimensions, Weight & Mechanical Design
Weight 59 kg (net)
Electrical, Power & Drive Specifications
Current consumption 13 A (max)
Fuse rating 16 A
Power supply 110-120V 1~ 50/60Hz
Interfaces, Connections & Control
Controller OLÉ
Display resolution 0, 1 K
Digital interface USB (Device), RS232 Interface
Temperature display OLED Display
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Protection rating IP20
Standards, Safety & General Data
Safety class I / NFL

Description

Construction and series positioning

The P010 OLÉ is a single-phase, air-cooled chiller in the Unichiller series, distinguished by the 'P' in its model code, which the manual identifies as particularly suitable for applications requiring high pressure drops. It uses a plastic pump (type B, non-adjustable speed) with G3/4 male connections and is rated IP20. Compared with sibling Unichiller 015 variants (63 dB(A)), this model is quieter at 57 dB(A). The refrigerant is R-449A (A1, H280) with a charge corresponding to 0.4 t CO2 equivalent.

Thermal and hydraulic behavior

Cooling capacity is strongly temperature-dependent: 1 kW at 15 °C, 0.8 kW at 0 °C, 0.5 kW at -10 °C and 0.15 kW at -20 °C, valid at 20 °C room temperature. Pump flow also depends on external pressure drop: 21 l/min at 0.5 bar, 17 l/min at 1.0 bar, 11 l/min at 1.5 bar and 6 l/min at 2.0 bar. The minimum filling capacity is 3.8 l and the expansion tank is 1.7 l. The unit is intended for externally closed applications only.

Installation, control and operation

Electrical supply is 110-120 V single-phase 50/60 Hz, max current 13 A, with a 16 A fuse; voltage tolerance is ±5% with simultaneous frequency tolerance of ±2%, and combined worst-case deviations are not permitted. The OLÉ controller provides an OLED display with 0.1 K resolution and USB (Device) and RS232 interfaces. The unit must be installed indoors at 5–40 °C ambient, at least 300 lx illuminance and up to 2000 m altitude, with 50–200 cm wall clearance per side for maintenance. Leveling feet or parking brakes must be secured before start-up. The power-failure response is configurable (OFF/Standby, ON, Power Failure Auto), and Process Safety mode releases maximum cooling capacity when the overtemperature trigger is reached.

Integration & Operating Notes

Process Limits
Cooling capacity collapses at low setpoints

At -20 °C the unit delivers only 0.15 kW, versus 1 kW at 15 °C. Processes requiring sustained low-temperature duty must either reduce heat load or select a larger model; the capacity figures are valid at 20 °C room temperature and drop further if ambient rises.

Unichiller P010 OLÉ Technical Data, page 1
Process Limits
High-pressure-drop circuits reduce available flow

The pump delivers 21 l/min at 0.5 bar but only 6 l/min at 2.0 bar. The external circuit's pressure drop must be calculated against this curve; if the required flow cannot be met at the circuit's backpressure, undercooling or poor temperature stability will result.

Unichiller P010 OLÉ Technical Data, page 1
Cooling & Media
Plastic pump incompatible with acetone and polyglycols

The standard plastic pump is not resistant to acetone or polyglycols (depending on manufacturer). Fluid selection must avoid these media or a more resistant pump must be specified; for freeze protection, water should be mixed with glysantine or ethylene glycol.

Unichiller P010 OLÉ Technical Data, page 2
Electrical
Supply tolerance is narrow and non-cumulative

Voltage tolerance is ±5% only with a simultaneous frequency tolerance of ±2%; combined worst-case deviations are not allowed. The circuit must be sized for 13 A max current and protected with a 16 A fuse. Verify site supply quality before commissioning.

Unichiller P010 OLÉ Technical Data, page 2
Mounting
Indoor installation with strict ambient and clearance rules

The unit is IP20 and must be installed indoors at 5–40 °C ambient, at least 300 lx illuminance and up to 2000 m altitude. A wall clearance of 50–200 cm per side is required for maintenance. It must not be installed or started inside an ATEX zone.

Unichiller Operation Manual, pages 13 and 25
Mounting
Secure leveling feet and parking brakes before start-up

Before the unit is put into operation, parking brakes must be activated at the casters (if any) and/or leveling feet unscrewed/activated. This prevents movement and crushing injuries during operation.

Unichiller Operation Manual, page 31
Control & I/O
Configure power-failure response for process safety

The power-failure response can be set to OFF/Standby, ON, or Power Failure Auto via the Pilot ONE. For exothermic processes, Process Safety mode releases maximum cooling capacity when the overtemperature trigger is reached instead of switching off all poles.

Unichiller Operation Manual, pages 18–19
Maintenance
Refrigerant circuit work restricted to approved contractors

Work on the coolant circuit must be carried out by approved refrigeration/air-conditioning system contractors. The refrigerant is R-449A (A1, H280) with 0.4 t CO2 equivalent, which may trigger F-gas leak-check and documentation obligations.

Unichiller Operation Manual, page 17; Technical Data, page 1

Selection & Integration Q&A

When should I choose the P010 OLÉ over a Unichiller 015 variant?

Choose the P010 OLÉ for high-pressure-drop circuits (the 'P' designation) and where 57 dB(A) is preferred over the 63 dB(A) of the 015 series. The 015 variants may be considered when higher cooling capacity or different configurations are needed, but verify capacity at your setpoint.

What are the requirements for connecting the external circuit to the pump?

The pump connection is G3/4 male, so hoses and fittings must match this thread. Maximum tightening torques must not be exceeded and connections must be counterheld. The circuit must be externally closed, and the loop volume plus thermal expansion must be checked against the 3.8 l minimum filling capacity and 1.7 l expansion tank.

What mounting and duty-cycle limits apply from the manual?

Install indoors at 5–40 °C ambient, at least 300 lx illuminance, up to 2000 m altitude, with 50–200 cm wall clearance per side. Secure leveling feet or parking brakes before start-up. Do not install in an ATEX zone. Cooling capacity is valid at 20 °C room temperature and drops if ambient rises.

What maintenance and consumables are required, and what is not included in base delivery?

Refrigerant circuit work must be done by approved refrigeration contractors. For freeze protection, water should be mixed with glysantine or ethylene glycol; these fluids and hoses/fittings are not included. The plastic pump is not resistant to acetone or polyglycols. No specific service interval is stated in the provided digests.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Unichiller P010 OLÉ Technical Data
Datasheet ·111,0 КБ ·2 pp.
View PDF
PDF
Unichiller Operation Manual
Manual ·2,8 МБ ·82 pp.
View PDF