Peter Huber Kältemaschinenbau Unichiller 200Tw-H
Peter Huber Kältemaschinenbau ·Made in Germany · In Active Production

Peter Huber Kältemaschinenbau Unichiller 200Tw-H

Peter Huber Kältemaschinenbau Unichiller 200Tw-H — Recirculating chillers.

The Unichiller 200Tw-H is a water-cooled recirculating chiller with a 20 kW cooling capacity at 15 °C and a -20…100 °C working range, controlled by the Pilot ONE. It is the high-capacity modification in the Unichiller series, distinguished by its 200-size refrigeration circuit and 2 kW heating stage, intended for externally closed process loops requiring stable temperature control.

Peter Huber Kältemaschinenbau Unichiller Series — Model Comparison & Selection

Model Pump typeSafety classTemperature range, °CPower supplyExpansion volume, m³Minimum fill volume, m³
Unichiller 200Tw-H Current D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 110T C3I / NFL-10–40400V 3~ 50Hz0.007—
Unichiller 110T-H C3III / FL-10–100400V 3~ 50Hz0.007—
Unichiller 110Tw C3I / NFL-20–40400V 3~ 50Hz——
Unichiller 130T C3I / NFL-10–40400V 3~ 50Hz0.0390.014
Unichiller 130T-H C3III / FL-10–100400V 3~ 50Hz0.0390.014
Unichiller 130Tw C3I / NFL-20–40400V 3~ 50Hz——
Unichiller 160T C3I / NFL-10–40400V 3~ 50Hz0.0390.014
Unichiller 160T-H C3III / FL-10–100400V 3~ 50Hz0.0390.014
Unichiller 160Tw C3I / NFL-20–40400V 3~ 50Hz0.01—
Unichiller 180-H E1III / FL-20–100400V 3~ 50Hz0.0480.018
Unichiller 180T D3I / NFL-20–40400V 3~ 50Hz0.0390.014
Unichiller 180T-H D3III / FL-20–100400V 3~ 50Hz0.0390.014
Unichiller 180Tw D3I / NFL-20–40460V 3~ 60Hz0.0220.015
Unichiller 180Tw-H D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 180w E1I / NFL-20–40400V 3~ 50Hz0.0480.018
Unichiller 180w-H E1III / FL-20–100400V 3~ 50Hz0.0480.018
Unichiller 200T D3I / NFL-20–40460V 3~ 60Hz0.0390.014
Unichiller 210T D3I / NFL-20–40400V 3~ 50Hz0.0390.014
Unichiller 210T-H D3III / FL-20–100400V 3~ 50Hz0.0390.014
Unichiller 210Tw D3I / NFL-20–40400V 3~ 50Hz0.0220.015
Unichiller 230-H E1III / FL-20–100400V 3~ 50Hz0.0480.018
Unichiller 230w E1I / NFL-20–40400V 3~ 50Hz0.0480.018
Unichiller 230w-H E1III / FL-20–100460V 3~ 60Hz0.0480.018
Unichiller 250T D3I / NFL-20–40400V 3~ 50Hz0.0390.014
Unichiller 250T-H D3III / FL-20–100400V 3~ 50Hz0.0390.014
Unichiller 250Tw-H D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 260T D3I / NFL-20–40460V 3~ 60Hz0.0390.014
Unichiller 260T-H D3III / FL-20–100400V 3~ 50Hz0.0390.014
Unichiller 260Tw D3I / NFL-20–40400V 3~ 50Hz0.0220.015
Unichiller 260Tw-H D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 300T D3I / NFL-20–40400V 3~ 50Hz0.0390.014
Unichiller 300T-H D3III / FL-20–100460V 3~ 60Hz0.0390.014
Unichiller 300Tw D3I / NFL-20–40460V 3~ 60Hz0.0220.015
Unichiller 300Tw-H D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 350T D3I / NFL-20–40460V 3~ 60Hz0.0390.014
Unichiller 350Tw-H D3III / FL-20–100400V 3~ 50Hz0.0220.015
Unichiller 500Tw D3I / NFL-20–40400V 3~ 50Hz0.007—
Unichiller 600Tw D3I / NFL-20–40400V 3~ 50Hz0.007—
Unichiller 600Tw-H D3III / FL-20–100400V 3~ 50Hz0.007—
Unichiller 700Tw D3I / NFL-20–40400V 3~ 50Hz0.007—
Unichiller 800Tw D3I / NFL-20–40400V 3~ 50Hz0.007—
Unichiller GL 1000w Pressure pump, speed notI / NFL-20–40460V 3~ 60Hz0.05—
Unichiller GL 200w Pressure pump, speed notI / NFL-20–40460V 3~ 60Hz0.03—
Unichiller GL 250w Pressure pump, speed notI / NFL-20–40460V 3~ 60Hz0.03—
Unichiller GL 300w Pressure pump, speed notI / NFL-20–40400V 3~ 50Hz0.03—
Unichiller GL 400w Pressure pump, speed notI / NFL-20–40400V 3~ 50Hz0.03—
Unichiller GL 750w Pressure pump, speed notI / NFL-20–40400V 3~ 50Hz0.05—
Unichiller P180 E2I / NFL-20–40—0.0480.018
Unichiller P180-H E2III / FL-20–100400V 3~ 50Hz0.0480.018
Unichiller P180w E2I / NFL-20–40400V 3~ 50Hz0.0480.018
Unichiller P180w-H E2III / FL-20–100460V 3~ 60Hz0.0480.018
Unichiller P230 E2I / NFL-20–40460V 3~ 60Hz0.0480.018
Unichiller P230-H E2III / FL-20–100460V 3~ 60Hz0.0480.018

Full specifications

Core Performance & Functional Specifications
Expansion volume 22 l
Heating capacity 2 kW
Minimum fill volume 15 l
Pump connection G1 1/4 AG male
Pump speed adjustable no
Pump type D3
External sensor connection Pt100
Temperature range -20...100 °C
Dimensions, Weight & Mechanical Design
Weight 374 kg
Electrical, Power & Drive Specifications
Power supply 400V 3~ 50Hz
Interfaces, Connections & Control
Controller Pilot ONE
Digital interface Ethernet, USB (Host u. Device), RS232
Operating Conditions, Environment & Protection
Ambient temperature limit 5...40 °C
Cooling capacity 20 kW (at 15 °C)
at 0 °C: 11 kW · at -10 °C: 5 kW · at -20 °C: 3 kW
Cooling water connection G3/4 male
Cooling water consumption 445 l/h (cooling water at 15 °C, flow at -20 °C)
cooling water at 15 °C, flow at -10 °C: 610 l/h · cooling water at 15 °C, flow at 0 °C: 860 l/h · cooling water at 15 °C, flow at 15 °C: 725 l/h
Cooling water differential pressure 1 bar (min)
Cooling Water Pressure 6 bar (max)
Protection rating IP20
Standards, Safety & General Data
Safety class III / FL

Description

Construction and series positioning

Performance and load behavior

Installation, control and operation

Integration & Operating Notes

Process Limits
Cooling water inlet must stay between 5 and 20 °C

Operating with cooling water outside this window risks reduced capacity or condensation; if the cooling water temperature falls below the dew point, the internal cooling-water pipes must be insulated to prevent condensate damage.

Unichiller 200Tw-H Datasheet, page 2
Process Limits
External circuit must be closed and sized for 15 l minimum

The unit is designed exclusively for externally closed applications; an open bath will cause fluid loss and unsafe operation. The external loop must hold at least 15 l, and the 22 l expansion volume must be accommodated in the circuit design.

Unichiller Operation Manual, page 34; Datasheet page 2
Electrical
Do not combine -5% voltage with +2% frequency

The supply must remain within ±5% voltage and ±2% frequency, but the specific combination of -5% voltage and +2% frequency is explicitly prohibited and may cause malfunction or damage to the compressor and controls.

Unichiller 200Tw-H Datasheet, page 2
Electrical
Three-phase unit supplied with cable but no plug

Because the current draw is below 63 A, the unit arrives with a power cable but without a plug; a suitable 400 V 3~ plug must be procured and fitted on site by a qualified electrician before commissioning.

Unichiller 200Tw-H Datasheet, page 2
Mounting
Maintain 50–200 cm wall clearance on either side

Free-standing installation requires this clearance for maintenance access and airflow; failing to provide it will obstruct service work on the refrigeration circuit and may affect heat rejection from the water-cooled condenser.

Unichiller Operation Manual, page 25
Mounting
Indoor use only, at least 300 lx illuminance

The unit is not explosion-protected and must not be installed in an ATEX zone. It is restricted to indoor locations with a minimum illuminance of 300 lx and a maximum altitude of 2000 m; ambient temperature must remain between 5 and 40 °C.

Unichiller Operation Manual, pages 13, 25; Datasheet page 2
Mounting
Activate leveling feet and parking brakes before start-up

Before switching on, the casters' parking brakes must be applied and/or the leveling feet unscrewed to stabilize the 374 kg unit; otherwise vibration or accidental movement during operation can cause crushing injuries or connection leaks.

Unichiller Operation Manual, page 31
Control & I/O
Configure Process Safety mode for exothermic reactions

In Process Safety mode, the controller releases maximum cooling capacity when the adjustable overtemperature trigger is reached instead of cutting all poles; this prevents runaway temperatures in exothermic processes but requires the OT trigger to be set appropriately for the application.

Unichiller Operation Manual, page 18
Control & I/O
Select power-failure response matching process risk

The Pilot ONE can be set to OFF/Standby, ON, or Power Failure Auto after a mains interruption; the choice determines whether the process restarts automatically or remains safe, and must be aligned with the process hazard analysis.

Unichiller Operation Manual, page 19
Maintenance
Refrigerant circuit work only by approved contractors

Any intervention on the R-449A circuit (2.35 kg, 3.3 t CO₂e) must be performed by certified refrigeration/air-conditioning contractors; unauthorized work risks refrigerant release and voids compliance with H280 safety obligations.

Unichiller Operation Manual, page 17; Datasheet page 1
Maintenance
Shut off cooling water even for overnight downtime

The cooling water supply must be closed during short idle periods to prevent water damage and corrosion inside the unit; this is especially important for water-cooled models where residual pressure can cause leaks.

Unichiller Operation Manual, page 28

Selection & Integration Q&A

When should I choose the Unichiller 200Tw-H over the smaller 110T/110Tw siblings?

Choose the 200Tw-H when you need up to 20 kW cooling at 15 °C and a 2 kW heating stage for externally closed loops; the 110T/110Tw siblings offer lower capacity and are air-cooled (110T) or water-cooled (110Tw) without the -H heating option. The 200Tw-H is the high-capacity water-cooled variant.

What are the requirements for the cooling water supply and the process loop connections?

Cooling water: 5–20 °C inlet, 1–6 bar differential pressure, G3/4 male connections; flow required up to 860 l/h at 0 °C process. Process loop: G1 1/4 AG male pump connections, minimum 15 l fill, 22 l expansion volume, and the loop must be externally closed.

What ambient and installation limits apply to the 200Tw-H?

Indoor use only, 5–40 °C ambient, at least 300 lx illuminance, max 2000 m altitude, IP20 (dry location). Maintain 50–200 cm wall clearance per side for maintenance. Not for ATEX zones. Leveling feet and parking brakes must be engaged before start-up.

What maintenance and accessories are required beyond the base unit?

A 400 V 3~ plug must be procured (cable supplied without plug). Refrigerant circuit work requires approved contractors. Cooling water must be shut off during downtime. No external sensor is included; a Pt100 can be connected. Regular maintenance per manual; no consumables listed in base delivery.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
Unichiller 200Tw-H Datasheet
Datasheet ·79,8 КБ ·2 pp.
View PDF
PDF
Unichiller Operation Manual
Manual ·2,8 МБ ·82 pp.
View PDF